Signed-off-by: Wolfgang Denk <wd@denx.de>

The editenv command can be used to edit an environment variable.
Editing an environment variable is useful when one wants to tweak an
existing variable, for example fix a typo or change the baudrate in the
'bootargs' environment variable.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>

Breaks building on many boards, and no really clean fix available yet.

This reverts commit 6dab6add2d8ee80905234b326abc3de11be1d178.

Simply add some defines, and adjust TLBe setup to include some
space for eLBC NAND.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

eSDHC is mutually exlusive with UART0 (in 4-bits mode) and I2C2
(in 1-bit mode). When eSDHC is used, we should switch u-boot console to
UART1, and make the proper device-tree fixups.

Because of an erratum in prototype boards it is impossible to use eSDHC
without disabling UART0 (which makes it quite easy to 'brick' the board
by simply issung 'setenv hwconfig esdhc', and not able to interact with
U-Boot anylonger).

So, but default we assume that the board is a prototype, which is a most
safe assumption. There is no way to determine board revision from a
register, so we use hwconfig.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

This change has 3 goals:
- Have secondary cores be released into spin loops at their 'true'
  address in SDRAM.  Previously, secondary cores were put into spin
  loops in the 0xfffffxxx address range which required that boot page
  translation was always enabled while cores were in their spin loops.

- Allow the TLB window that the primary core uses to access the
  secondary cores boot page to be placed at any address.  Previously, a
  TLB window at 0xfffff000 was always used to access the seconary cores'
  boot page.  This TLB address requirement overlapped with other
  peripherals on some boards (eg XPedite5370).  By default, the boot
  page TLB will still use the 0xfffffxxx address range, but this can be
  overridden on a board-by-board basis by defining a custom
  CONFIG_BPTR_VIRT_ADDR.  Note that the TLB used to map the boot page
  remains in use while U-Boot executes.  Previously it was only
  temporarily used, then restored to its initial value.

- Allow Boot Page Translation to be disabled on bootup.  Previously,
  Boot Page Translation was always left enabled after secondary cores
  were brought out of reset.  This caused the 0xfffffxxx address range
  to somewhat "magically" be translated to an address in SDRAM.  Some
  boards may not want this oddity in their memory map, so defining
  CONFIG_MPC8xxx_DISABLE_BPTR will turn off Boot Page Translation after
  the secondary cores are initialized.

These changes are only applicable to 85xx boards with CONFIG_MP defined.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Originally written by Jason Jin and Mingkai Hu for mpc8536.

When QorIQ based board is configured as a PCIe agent, then unlock/enable
inbound PCI configuration cycles and init a 4K inbound memory window;
so that a PCIe host can access the PCIe agents SDRAM at address 0x0

* Supported in fsl_pci_init_port() after adding pcie_ep as a param
* Revamped copyright in drivers/pci/fsl_pci_init.c
* Mods in 85xx based board specific pci init after this change

Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>