u-boot.git/include, branch v2011.06-rc2

armv7: Add support for ST-Ericsson U8500 href platform

2011-06-01T17:31:03+00:00

Minimal platform support to boot linux from SD.

Supported devices/hw limited to external MMC/SD slot,
GPIO, I2C and minimal PRCMU.

Signed-off-by: John Rigby 
CC: Albert Aribaud

Kirkwood: boards cleanup for deprecated CONFIG_CMD_AUTOSCRIPT

2011-05-31T21:51:55+00:00

arm/km: update mgcoge3un board support

2011-05-31T17:46:19+00:00

We change default settings for egiga on mgcoge3un.
The reason we need this is that we have the gig port on mgcoge3un
connected using a back-to-back pair of PHYs. There are no magnetics and
because of that the port has to be run with a fixd configuration and
auto-negotiation must be disabled. In the default mode the egiga driver
uses autoneg to determine port speed - which defaults to 1G (we need
100M full duplex).

Add wait for the GPIO line connected to mgcoge3ne before
starting mgcoge3un. A board specific ethernet present function
was added, because on this board ethernet is always present.
The BOCO FPGA access was enhanced and changed to use register
definitions.

Signed-off-by: Holger Brunck 
Signed-off-by: Valentin Longchamp 
Acked-by: Heiko Schocher 
cc: Wolfgang Denk 
cc: Detlev Zundel 
cc: Prafulla Wadaskar

arm/km: rename mgcoge2un to mgcoge3un

2011-05-31T17:45:59+00:00

The mgcoge2un target was only an intermediate step to mgcoge3un.
For this reason the mgcoge2un support was moved to mgcoge3un,
because it isn't needed to support both targets.

We add the BootROM init file for the mgcoge3un memphis RAM.

We also move the suen3 and suen8 boards into the correct category
in the MAINTAINERS file.

Signed-off-by: Valentin Longchamp 
Signed-off-by: Holger Brunck 
Acked-by: Heiko Schocher 
cc: Wolfgang Denk 
cc: Detlev Zundel 
cc: Prafulla Wadaskar

arm/km: add second serial interface for kirkwood

2011-05-31T17:45:54+00:00

Signed-off-by: Holger Brunck 
Signed-off-by: Valentin Longchamp 
Acked-by: Heiko Schocher 
cc: Wolfgang Denk 
cc: Detlev Zundel 
cc: Prafulla Wadaskar

arm/km: disable ls (through jffs2 support)

2011-05-31T17:45:34+00:00

This is not supported on our km-arm boards since we have defined
CONFIG_SYS_NO_FLASH for our NAND Flash chip.

With CONFIG_CMD_JFFS2, the ls command is present and works very badly
on our km-arm boards.

Signed-off-by: Valentin Longchamp 
Signed-off-by: Holger Brunck 
Acked-by: Heiko Schocher 
Acked-by: Prafulla Wadaskar 
cc: Wolfgang Denk 
cc: Detlev Zundel

arm/km: introduce bootcount env variable and clean km_arm

2011-05-31T17:45:27+00:00

This environment variable is used to set the bootcount address
for the kernel.

last_stage_init is not available for arm platforms. So the
calls to set_km_var and set_bootcount_addr are done in
misc_init_r.

Additionally some unneeded printouts were removed.

Signed-off-by: Valentin Longchamp 
Signed-off-by: Holger Brunck 
Acked-by: Heiko Schocher 
cc: Wolfgang Denk 
cc: Detlev Zundel 
cc: Prafulla Wadaskar

arm/km: move CONFIG_EXTRA_ENV_SETTINGS from board to km_arm file

2011-05-31T17:45:24+00:00

Since all the boards define the same env settings, this simplifies
the board files.

Signed-off-by: Valentin Longchamp 
cc: Holger Brunck 
cc: Heiko Schocher 
cc: Wolfgang Denk 
cc: Detlev Zundel 
cc: Prafulla Wadaskar

arm/km: remove CONFIG_SYS_KWD_CONFIG from keymile-common.h

2011-05-31T17:45:02+00:00

This define is marvell specific, so it should be present in km_arm.
It is however not needed there either, since we set it to the default
value that is already set in include/asm/arch-kirkwood/config.h

Signed-off-by: Valentin Longchamp 
cc: Holger Brunck 
cc: Prafulla Wadaskar 
cc: Heiko Schocher 
cc: Wolfgang Denk 
cc: Detlev Zundel

ARMV7: Add support for Samsung SMDKV310 Board

2011-05-26T10:33:44+00:00

SMDKV310 board is based on Samsung S5PV310 SOC. This SOC is very much
similar to S5PC210.

Signed-off-by: Chander Kashyap 
Signed-off-by: Tushar Behera 
Signed-off-by: Minkyu Kang