u-boot.git/include, branch v2012.10-rc2

lib: add gzip lib function callback

2012-09-29T14:26:08+00:00

Signed-off-by: Lei Wen

lib: zlib: include deflate into zlib build

2012-09-29T14:26:08+00:00

Add a new config CONFIG_GZIP_ENABLED, if enabled, the uboot bin would
include zlib's deflate method which could be used for compressing.

Signed-off-by: Lei Wen

Merge branch 'master' of git://git.denx.de/u-boot-net

2012-09-27T19:06:07+00:00

SPL: SPI: Enhance spi_spl_load to match the other load functions

2012-09-27T18:20:27+00:00

Signed-off-by: Tom Rini

SPL: Add option to skip copying of the mkimage header

2012-09-27T18:20:27+00:00

On some system (e.g. powerpc), the load-address and entry-point is
located at address 0. So the current approach to load the image
(payload) including the header to the address "load-address - 64"
can't work here.

This patch adds an flag to skip this copying including header to
the SPL framework. By setting SPL_COPY_PAYLOAD_ONLY, only the
playload will be copied. This will be used by the SPL NOR flash
driver on powerpc.

Signed-off-by: Stefan Roese 
Signed-off-by: Tom Rini

SPL: Add NOR flash booting support

2012-09-27T18:20:27+00:00

SPL NOR flash booting support is quite simple. Only copying of the
images is needed.

On MPC5xxx we need to make sure to only use the standard memcpy()
implementation and not the MPC5xxx specific one. As the MPC5xxx
version has some complexity which is not needed for this SPL
booting.

Signed-off-by: Stefan Roese 
Signed-off-by: Tom Rini

hawkboard: Update config file to work with common spl framework

2012-09-27T18:20:26+00:00

The common spl framework expects the u-boot payload size through
CONFIG_SYS_MONITOR_LEN. Define the macro with the u-boot's size. With
this change, CONFIG_SYS_NAND_U_BOOT_SIZE is no longer required. Delete
the same.

Signed-off-by: Tom Rini 
Signed-off-by: Sughosh Ganu

ARM: SPL: Convert davinci to CONFIG_SPL_FRAMEWORK

2012-09-27T18:20:10+00:00

- Convert the non-relocation part of board_init_f to spl_board_init, turn on CONFIG_SPL_BOARD_INIT in the configs.
- Remove duplicated code.
- Add spl_boot_device() that returns the statically chosen boot device.

Signed-off-by: Tom Rini

net/phy: support the mv88e6352 switch

2012-09-27T17:21:56+00:00

This patch add support for the configuration of an external switch from
the 88E6xxx series from Marvell trough an MDIO link using indirect
adressing. This can be used if we do not want to use an EEPROM for the
configuration.

This driver is not generic and was not tested on other switches than the
88e6352. This is proposed as a first implementation that is somewhat
limited but works and that can be used as a basis for further
developments for this switch family.

Signed-off-by: Valentin Longchamp 
cc: Holger Brunck 
cc: Prafulla Wadaskar 
cc: Joe Hershberger

SPL: Create arch/arm/lib/spl.c for board_init_f and jump_to_image_linux

2012-09-27T16:49:59+00:00

In SPL (CONFIG_SPL_FRAMEWORK) board_init_f must setup the stack pointer,
clear the BSS and call board_init_r.  We mark this as weak as some
platforms may need to perform additional initalization at this point.
We provide a gd that we know will be in a usable location, once the BSS
has been cleared to help with this as well.  Finally, we no longer call
relocate_code so remove that from the armv7 version.

Next, both board_init_f and jump_to_image_linux are going to be
inherently arch-specific, so move these versions to arch/arm/lib/spl.c

Signed-off-by: Tom Rini