Small conflict over DRA7XX updates and adding SRAM_SCRATCH_SPACE_ADDR

Conflicts:
	arch/arm/include/asm/arch-omap5/omap.h

Signed-off-by: Tom Rini <trini@ti.com>

LP-8x4x is a programmable automation controller by ICP DAS. It is
shipped with outdated U-Boot v1.3.0

This patch adds enough supports to boot the board:
 - 128M of 128M SDRAM
 - 32M of 48M NOR Flash memory
 - 1 of 4 Serial consoles (PXA FFUART)
 - 2 of 2 Ethernet controllers (DM9000)

Signed-off-by: Sergey Yanovich <ynvich@gmail.com>
Series-to: u-boot
Series-cc: marex

This patch adds support to both Faraday FUSBH200 and FOTG210,
the differences between Faraday EHCI and standard EHCI are
listed bellow:

1. The PORTSC starts at 0x30 instead of 0x44.
2. The CONFIGFLAG(0x40) is not only un-implemented, and
   also has its address space removed.
3. Faraday EHCI is a TDI design, but it doesn't
   compatible with the general TDI implementation
   found at both U-Boot and Linux.
4. The ISOC descriptors differ from standard EHCI in
   several ways. But since U-boot doesn't support ISOC,
   we don't have to worry about that.

Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Marek Vasut <marex@denx.de>

Use unaligned access to fetch wMaxPacketSize in usb_endpoint_maxp()
api.
In its absence we see following data abort message:
==============================================================
data abort

    MAYBE you should read doc/README.arm-unaligned-accesses

pc : [<bf794e24>]          lr : [<bf794e1c>]
sp : bf37c7b0  ip : 0000002f     fp : 00000000
r10: 00000000  r9 : 00000002     r8 : bf37fecc
r7 : 00000001  r6 : bf7d8931     r5 : bf7d891c  r4 : bf7d8800
r3 : bf7d65b0  r2 : 00000002     r1 : bf7d65b4  r0 : 00000027
Flags: nZCv  IRQs off  FIQs off  Mode SVC_32
Resetting CPU ...

resetting ...
==============================================================

Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Ilya Yanok <ilya.yanok@cogentembedded.com>
Cc: Marek Vasut <marex@denx.de>

The flash_info_t->start[] field is limited in size by CONFIG_SYS_MAX_FLASH_SECT
macro, which is set to 19 for this board in the board config file. If we inspect
the board/ppmc7xx/flash.c closely, especially the flash_get_size() function, we
can notice the "switch ((long)flashtest)" at around line 80 having a few results
which will set flash_info_t->sector_count to value higher than 19, for example
"case AMD_ID_LV640U" will set it to 128. Notice that right underneath, iteration
over flash_info_t->start[] happens and the upper bound for the interation is
flash_info_t->sector_count. Now if the sector_count is 128 as it is for the
AMD_ID_LV640U case, but the CONFIG_SYS_MAX_FLASH_SECT limiting the start[] is
only 19, an access past the start[] array much happen. Moreover, during this
iteration, the field is written to, so memory corruption is inevitable.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Richard Danter <richard.danter@windriver.com>

C99's strict aliasing rules are insane to use in low-level code such as a
bootloader, but as Wolfgang has rejected -fno-strict-aliasing in the
past, add a union so that 16-bit accesses can be performed.

Compile-tested only.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Wolfgang Denk <wd@denx.de>

Move pinmux configurations for the DA830 SoCs from board file
to the arch tree so that it can be used for all da830 based devices.
Also, avoids duplicate pinmuxing in case of NAND.

Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Christian Riesch <christian.riesch@omicron.at>