u-boot.git/include, branch v2015.04-rc5

Merge branch 'master' of git://git.denx.de/u-boot-atmel

2015-03-31T23:15:59+00:00

ARM: at91: sama5: move the common part of configurations to at91-sama5_common.h

2015-03-31T23:04:32+00:00

Create a new configuration file: at91-sama5_common.h. Which includes the
configurations that reused by all SAMA5 chips.

at91-sama5_common.h includes:
- hw macros (clock, text_base and etc.)
- default commands.
- BOOTARGS
- U-Boot common configs.
NOTE: NOR flash definition should be put before including the common header.

For sama5d3-xplained:
- add CMD_SETEXPR

For sama5d3xek:
- add CMD_SETEXPR
- change CONFIG_SYS_MALLOC_LEN to (4*1024*1024)

Signed-off-by: Josh Wu

ARM: atmel: at91sam9n12ek: enable spl support

2015-03-31T23:04:31+00:00

Enable SPL support for at91sam9n12ek boards, now it supports
boot up from NAND flash, serial flash.

Signed-off-by: Bo Shen

ARM: atmel: at91sam9x5ek: enable spl support

2015-03-31T23:04:31+00:00

Enable SPL support for at91sam9x5ek board. Now, it supports
boot up from NAND flash and SPI flash.

Signed-off-by: Bo Shen

ARM: atmel: at91sam9m10g45ek: enable spl support

2015-03-31T23:04:30+00:00

Supports boot up from NAND flash with software ECC eanbled.
And supports boot up from SD/MMC card with FAT file system.

As the boot from SD/MMC card with FAT file system, the BSS
segment is too big to fit into SRAM, so, use the lds to put
it into SDRAM.

Signed-off-by: Bo Shen

ARM: at91: at91sam9n12ek: save the environment to a fat file in MMC card

2015-03-31T23:04:29+00:00

Insteading in mmc's raw sectors, this patch will save the environment
in a fat file (uboot.env) in mmc card's first FAT patition by default.

If you want to save in mmc's raw sectors, you only need to define
CONFIG_ENV_IS_IN_MMC.

Signed-off-by: Josh Wu 
Acked-by: Bo Shen

arm, at91: corvus: move MACH_TYPE to defconfig

2015-03-31T23:04:28+00:00

move MACH_TYPE into defconfig

Signed-off-by: Heiko Schocher

Merge git://git.denx.de/u-boot-nand-flash

2015-03-31T21:17:06+00:00

Merge branch 'master' of git://git.denx.de/u-boot-imx

2015-03-31T15:45:36+00:00

nand: yaffs: Remove the "nand write.yaffs" command

2015-03-31T04:24:39+00:00

This command is only enabled by one board, complicates the NAND code,
and doesn't appear to have been functioning properly for several
years.  If there are no bad blocks in the NAND region being written
nand_write_skip_bad() will take the shortcut of calling nand_write()
which bypasses the special yaffs handling.  This causes invalid YAFFS
data to be written. See
http://lists.denx.de/pipermail/u-boot/2011-September/102830.html for
an example and a potential workaround.

U-Boot still retains the ability to mount and access YAFFS partitions
via CONFIG_YAFFS2.

Signed-off-by: Peter Tyser