Since commit 09c3280754f8 (mtd, nand: Move common functions from
cmd_nand.c to common place), NAND commands would not work at all
on large devices.

    => nand read 80000000 10000 10000

    NAND read: Offset exceeds device limit
    => nand erase 100000 100000

    NAND erase: Offset exceeds device limit

The type of the "size" of "struct mtd_info" is uint64_t, while
mtd_arg_off_size() and mtd_arg_off() treat chipsize as int type.
The chipsize is wrapped around if the argument is given with 2GB
or larger.

Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

This patch enabled the USB/EHCI support for the Marvell
DB-88F6820-GP eval board.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>

Configure and enable the SATA/SCSI (AHCI) support for the Marvell
DB-88F6820-GP eval board.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>

This patch adds support for the common AHCI controller on the Marvell
Armada 38x.

Tested on the Marvell DB-88F6820-GP eval board.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>

This patch adds MMC/SDIO support to the Marvell DB-88F6820-GP board
configuration. Including support for the common partitions and
filesystems.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>

When compling under 64bit platforms, there are lots of warnings,
like:

drivers/block/ahci.c:114:18: warning: cast to pointer from integer
 of different size [-Wint-to-pointer-cast]
  u8 *port_mmio = (u8 *)probe_ent->port[port].port_mmio;
                  ^
drivers/block/ahci.c: In function ?.hci_host_init?.
drivers/block/ahci.c:218:49: warning: cast from pointer to integer
 of different size [-Wpointer-to-int-cast]
   probe_ent->port[i].port_mmio = ahci_port_base((u32) mmio, i);

......

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>

Baltos has USB0 connected to a USB hub and thus is host-only. USB1
is connected to microUSB connector and thus should use OTG mode.

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>

Because it is possible for the MTD number to change, causing a
filesystem mount failure, we should use the volume name instead
of the MTD number and let Linux resolve the correct one.

Signed-off-by: Mike Scherban <m-scherban@ti.com>

On STM32F429 gpio PC6/PC7 can be allocated for USART6, as
reported in the comment.
But current code in
	drivers/serial/serial_stm32.c
uses a different gpio mapping (PG14/PG9) for USART6.

Fix the comment to match current code in the driver.

Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
To: u-boot@lists.denx.de
To: Kamil Lulko <rev13@wp.pl>
Cc: Tom Rini <trini@konsulko.com>