Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>

Between v2015.07-rc1 and v2015.07-rc2 this board started
silent boot failure.  A bisect led to commit 6eed3786c68c8a49d
("net: Move the CMD_NET config to defconfigs").  This commit
looks harmless in itself, but it did implicitly add a feature
to the image which led to this:

 u-boot$git describe 6eed3786c68c8a49d
 v2015.07-rc1-412-g6eed3786c68c
              ^^^

 u-boot$ls -l ../41*/u-boot.bin
 -rwxrwxr-x 1 paul paul 261476 Oct 16 16:47 ../411/u-boot.bin
 -rwxrwxr-x 1 paul paul 266392 Oct 16 16:43 ../412/u-boot.bin
 u-boot$bc
 bc 1.06.95
 Copyright 1991-1994, 1997, 1998, 2000, 2004, 2006 Free Software Foundation, Inc.
 This is free software with ABSOLUTELY NO WARRANTY.
 For details type `warranty'.
 256*1024
 262144

i.e. we finally broke through the 256k monitor size.  Jump it
up to 384k and fix the hard coded value used in the env offset
at the same time.

We were probably flirting with the 256k size issue without
knowing it when testing on different baselines in earlier
commits, but since this is all board specific, a rebase or
reorder to put this commit 1st is of little value.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>

When debugging an env fail due to too small a malloc pool, it
was noted that the env write was 256k.  But the device sector
size is 1/2 that, as can be seen from "fli" output:

Bank # 1: CFI conformant flash (16 x 16)  Size: 16 MB in 131 Sectors
  Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x1888
  Erase timeout: 4096 ms, write timeout: 1 ms
  Buffer write timeout: 2 ms, buffer size: 64 bytes

  Sector Start Addresses:
  FF000000 E RO   FF020000 E RO   FF040000 E RO   FF060000 E RO   FF080000 E RO
  FF0A0000 E RO   FF0C0000 E RO   FF0E0000 E RO   FF100000 E RO   FF120000 E RO
  [...]
  FFF00000   RO   FFF20000   RO   FFF40000   RO   FFF60000   RO   FFF80000   RO
  FFFA0000   RO   FFFC0000   RO   FFFE0000 E RO   FFFE8000   RO   FFFF0000 E RO
  FFFF8000   RO
=>

The desired env sector is FFF40000->FFF60000, or 0x20000 in length,
just after the 256k u-boot image which starts @ FFF00000.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>

Currently the board fails to save its env, since the env size
is much smaller than the sector size, and the malloc fails for
the pad buffer, giving the user visible symptom of:

Unable to save the rest of sector (253952)

Allow for 1M malloc pool, the same as used on the sbc8548 board.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>

It is just too painful to use interactively without it.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>

Used NAND chips requires at least 4-bit error correction, so use BCH8
as it is what kernel uses.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Javier Martinez Canillas <javier@osg.samsung.com>

Juno comes with 8GB RAM, but U-Boot only passes 2GB to the kernel.
Declare a secondary memory bank and set the sizes correctly.

Signed-off-by: Liviu Dudau <Liviu.Dudau@foss.arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>

The default dockstar configuration for U-Boot currently causes it to
overrun the environment area, so that a "saveenv" command bricks the
device.  This patch moves the environment to a higher address to avoid
that.

Signed-off-by: Eric Cooper <ecc@cmu.edu>