u-boot.git/include, branch v2026.04-rc1

power: regulator: add AXP318W support

2026-01-25T23:29:32+00:00

The PMIC is also known as AXP819 in vendor pmu code

For DCDC6, 8, 9, the underlying hardware support more than two levels
voltage step tuning, but for now only first two levels are implemented
in this driver, hence highest voltage will be limited at seccond level.
It actual meets board requirement in current design, and we've verified
it in Radxa Cubie A7A board.

Following are detail explanation of voltage tuning stpes for those DCDCs:

DCDC | voltage range  | units | steps | implemented
 6   | 0.5   -  1.2   | 10 mV | 71    | Y
 .   | 1.22  -  1.54  | 20 mV | 17    | Y
 .   | 1.8   -  2.4   | 20 mV | 31    | N
 .   | 2.44  -  2.76  | 40 mV | 9     | N
 --------------------------------------------------
 8/9 | 0.5   -  1.2   | 10 mV | 71    | Y
 .   | 1.22  -  1.84  | 20 mV | 32    | Y
 .   | 1.9   -  3.4   | 100mV | 16    | N

Signed-off-by: Yixun Lan 
Reviewed-by: Andre Przywara

arm: Remove remainder of ARCH_ORION5X

2026-01-21T18:05:15+00:00

With commit 5663b137e682 ("arm: Remove edminiv2 board") the last
ARCH_ORION5X platform was removed. Remove the rest of the architecture
code which is now unused.

Reviewed-by: Tony Dinh 
Signed-off-by: Tom Rini

Merge tag 'xilinx-for-v2026.04-rc1-v2' of https://source.denx.de/u-boot/custodians/u-boot-microblaze

2026-01-19T19:08:48+00:00

AMD/Xilinx/FPGA changes for v2026.04-rc1 v2

microblaze:
- Fix spl_boot_list order

versal2:
- Fix EMMC distro boot setup
- Align distro boot variables with memory layout

zynqmp-phy:
- Sync with Linux kernel driver

zynqmp:
- Add verify_auth command
- DT sync
- Add placing variables to FAT/EXT4
- Enable PCIe driver by default

pcie - xilinx-nwl:
- Fix Link down crash

ufs:
- Align clock/reset with DT binding

# -----BEGIN PGP SIGNATURE-----
#
# iHUEABYIAB0WIQSXAixArPbWpRanWW+rB/7wTvUR9QUCaW3p3wAKCRCrB/7wTvUR
# 9VkwAP4jPRALpM34VpTimNe/iwigIx8hAHxbvkUU0oJ/DW6W8AEAhCSL+ydgreuv
# kKCyNiOF1sm8IrOh4TdtMIFn37d4Dwg=
# =AkKK
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 19 Jan 2026 02:22:55 AM CST
# gpg:                using EDDSA key 97022C40ACF6D6A516A7596FAB07FEF04EF511F5
# gpg: Can't check signature: No public key

ARM: imx: Enable boot from both USB controllers on all i.MX6 DHSOM

2026-01-17T18:00:42+00:00

Enable boot from both USB controller 0 and 1 on all i.MX6 DHSOM.

Signed-off-by: Marek Vasut

Merge branch 'qcom-main' of https://source.denx.de/u-boot/custodians/u-boot-snapdragon

2026-01-16T21:14:37+00:00

We have been getting a lot more patches from Qualcomm engineers, largely
focusing on IoT, router, and automotive platforms (those with QCS, IPQ,
and SA prefixes specifically).

Quite a variety of changes here:
- Watchdog overflow fix
- Hardcoded fastboot buffer addresses for a few board (hoppefully
  temporary until fastboot is updated to read $fastboot_addr_r)
- Enable memory protection (MMU_MGPROT) for ARCH_SNAPDRAGON
- pinctrl support for the QCS615 soc
- various USB/phy fixes including phy config for msm8996/qcs615
- mmc and i2c clock configuration fixes
- significant fixes for rpmh and regulator drivers
- added config fragment for pixel devices
- sa8775p clock fixes
- support for "flattened" dwc3 DT that recently landed upstream for
  sc7280 (qcs6490) and a few other platforms

configs: mt8365: remove empty header file

2026-01-16T19:04:16+00:00

Remove the empty include/configs/mt8365.h header file as it is not
needed. The Kconfig entry that referenced it is also removed.

Signed-off-by: David Lechner

Merge patch series "video: simple_panel support for am335x evm panel"

2026-01-16T15:53:57+00:00

Markus Schneider-Pargmann (TI.com)  says:

This series adds the capability to define hardcoded panel settings to
the simple_panel driver similar to the Linux Kernel and adds the panel
used on am335x evm. panel-uclass.c is extended to support get_modes()
for panels and drm_display_mode conversion. In a second step the tilcdc
is extended to support OF graph to be able to connect to the simple
panel devicetree node.

Link: https://lore.kernel.org/r/20260105-topic-am33-evm-lcd-v2026-01-v4-0-7617591b8159@baylibre.com

panel: Lightweight support of get_modes()

2026-01-16T15:07:28+00:00

Linux uses get_modes() to fetch all available panel modes from the
driver. This is also used to fetch the modes from Linux's simple panel
implementation where a list of drm_display_mode structs is used to
define the different possible panels.

To make our work easier, create a compatible way of fetching and
defining these modes in u-boot. get_modes() fetches the available modes
from the panel driver. The get_display_timing() call maps the
drm_display_mode properties to the display_timing struct. This call now
uses whatever panel operation is available, get_display_timing() or
get_modes().

Reviewed-by: Fabio Estevam 
Signed-off-by: Markus Schneider-Pargmann (TI.com)

panel: Add missing comment for the timing argument

2026-01-16T15:07:28+00:00

For completeness add it.

Signed-off-by: Markus Schneider-Pargmann (TI.com)

net: lwip: nfs: Port the NFS code to work with lwIP

2026-01-15T10:09:28+00:00

After the preparatory patches moved most of the NFS code into common
files we now add the code to enable NFS support with lwIP.

Signed-off-by: Andrew Goodbody 
Acked-by: Jerome Forissier