u-boot.git/lib/asm-offsets.c, branch v2018.09

SPDX: Convert all of our single license tags to Linux Kernel style

2018-05-07T13:34:12+00:00

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini

ARMv8: get new GD address from gd->new_gd directly

2017-10-08T20:19:56+00:00

the new GD address is calculated via board data BD currently
it require the new GD area locates below BD tightly, so a strict
constraint is imposed on memory layout which maybe make special
platform unpleasant.

fix it by getting new GD address from gd->new_gd directly.

Signed-off-by: zijun_hu 
Reviewed-by: Simon Glass

spl: make SPL and normal u-boot stage use independent SYS_MALLOC_F_LEN

2017-07-27T12:59:03+00:00

Some platforms have very limited SRAM to run SPL code, so there may
not be the same amount space for a malloc pool before relocation in
the SPL stage as the normal U-Boot stage.

Make SPL and (the full) U-Boot stage use independent SYS_MALLOC_F_LEN,
so the size of pre-relocation malloc pool can be configured memory
space independently.

Signed-off-by: Andy Yan 
Reviewed-by: Tom Rini 
Acked-by: Philipp Tomsich 
Reviewed-by: Philipp Tomsich 
[fixed up commit-message:]
Signed-off-by: Philipp Tomsich

lib/asm-offsets - make GD_RELOCADDR, GD_RELOC_OFF & GD_START_ADDR_SP available for all architectures

2015-03-06T01:50:28+00:00

GD_RELOCADDR, GD_RELOC_OFF & GD_START_ADDR_SP are generic members of
global data structure so why don't we allow architectures other than ARM
to use it.

Signed-off-by: Alexey Brodkin 
Cc: Simon Glass 
Cc: Tom Rini 
Acked-by: Simon Glass

x86: Clean up asm-offsets

2014-12-14T05:32:04+00:00

Move GD_BIST from lib/asm-offsets.c to arch/x86/lib/asm-offsets.c
as it is x86 arch specific stuff. Also remove GENERATED_GD_RELOC_OFF
which is not referenced anymore.

Signed-off-by: Bin Meng 
Acked-by: Simon Glass

x86: Save the BIST value on reset

2014-11-21T06:24:10+00:00

The built in self test value is available in register eax on start-up. Save
it so that it can be accessed later. Unfortunately we must wait until the
global_data is available before we can do this, so there is a little bit of
shuffling to keep it around.

Signed-off-by: Simon Glass 
Reviewed-by: Bin Meng

Add a simple malloc() implementation for pre-relocation

2014-07-23T13:05:40+00:00

If we are to have driver model before relocation we need to support some
way of calling memory allocation routines.

The standard malloc() is pretty complicated:

1. It uses some BSS memory for its state, and BSS is not available before
relocation

2. It supports algorithms for reducing memory fragmentation and improving
performace of free(). Before relocation we could happily just not support
free().

3. It includes about 4KB of code (Thumb 2) and 1KB of data. However since
this has been loaded anyway this is not really a problem.

The simplest way to support pre-relocation malloc() is to reserve an area
of memory and allocate it in increasing blocks as needed. This
implementation does this.

To enable it, you need to define the size of the malloc() pool as described
in the README. It will be located above the pre-relocation stack on
supported architectures.

Note that this implementation is only useful on machines which have some
memory available before dram_init() is called - this includes those that
do no DRAM init (like tegra) and those that do it in SPL (quite a few
boards). Enabling driver model preior to relocation for the rest of the
boards is left for a later exercise.

Signed-off-by: Simon Glass

Add GPL-2.0+ SPDX-License-Identifier to source files

2013-07-24T13:44:38+00:00

Signed-off-by: Wolfgang Denk 
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini

arm: move C runtime setup code in crt0.S

2013-01-08T21:14:50+00:00

Move all the C runtime setup code from every start.S
in arch/arm into arch/arm/lib/crt0.S. This covers
the code sequence from setting up the initial stack
to calling into board_init_r().

Also, rewrite the C runtime setup and make functions
board_init_*() and relocate_code() behave according to
normal C semantics (no jumping across the C stack any
more, etc).

Some SPL targets had to be touched because they use
start.S explicitly or for some reason; the relevant
maintainers and custodians are cc:ed.

Signed-off-by: Albert ARIBAUD

Small coding style fix in lib/asm-offsets.c

2011-01-17T21:55:58+00:00

Signed-off-by: Stefan Roese 
Acked-by: Michal Simek