Move this header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>

If "object=" is specified in "keydir" when using the pkcs11 engine do
not append another "object=<key-name-hint>". This makes it possible to
use object names other than the key name hint. These two string
identifiers are not necessarily equal.

Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Bastian Krause <bst@pengutronix.de>
Reviewed-by: George McCollister <george.mccollister@gmail.com>

Better than crashing later if it is missing.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>

stdlib.h is the header for malloc since at least c89/c90.
There is no system malloc.h on OpenBSD and trying to use malloc.h here
falls back to the U-Boot malloc.h breaking the build of qemu_arm64.

Fixes: 336d4615f8 ("dm: core: Create a new header file for 'compat' features")
Signed-off-by: Jonathan Gray <jsg@jsg.id.au>

To fill the exponent field of the rsa_public_key struct, rsa_mod_exp_sw
did a cast to uint64_t of the key_prop->public_exponent field.
But that alignment is not guaranteed in all cases.

This came to light when in my spl-fit-signature the key-name exceeded
a certain length and with it the verification then started failing.
(naming it "integrity" worked fine, "integrity-uboot" failed)

key_prop.public_exponent itself is actually a void-pointer, fdt_getprop()
also just returns such a void-pointer and inside the devicetree the 64bit
exponent is represented as 2 32bit numbers, so assuming a 64bit alignment
can lead to false reads.

So just use the already existing rsa_convert_big_endian() to do the actual
conversion from the dt's big-endian to the needed uint64 value.

Fixes: fc2f4246b4b3 ("rsa: Split the rsa-verify to separate the modular exponentiation")
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Xilinx changes for v2020.07

common:
- Align ENV_FAT_INTERFACE
- Fix MAC address source print log
- Improve based autodetection code

xilinx:
- Enable netconsole

Microblaze:
- Setup default ENV_OFFSET/ENV_SECT_SIZE

Zynq:
- Multiple DT updates/fixes
- Use DEVICE_TREE environment variable for DTB selection
- Switch to single zynq configuration
- Enable NOR flash via DM
- Minor SPL print removal
- Enable i2c mux driver

ZynqMP:
- Print multiboot register
- Enable cache commands in mini mtest
- Multiple DT updates/fixes
- Fix firmware probing when driver is not enabled
- Specify 3rd backup RAM boot mode in SPL
- Add SPL support for zcu102 v1.1 and zcu111 revA
- Redesign debug uart enabling and psu_init delay
- Enable full u-boot run from EL3
- Enable u-boot.itb generation without ATF with U-Boot in EL3

Versal:
- Enable distro default
- Enable others SPI flashes
- Enable systems without DDR

Drivers:
- Gem:
  - Flush memory after freeing
  - Handle mdio bus separately
- Watchdog:
  - Get rid of unused global data pointer
  - Enable window watchdog timer
- Serial:
  - Change reinitialization logic in zynq serial driver

Signed-off-by: Tom Rini <trini@konsulko.com>

These are used in multiple places so update them to use a shared #define.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>

This function, and hence rsa_verify(), will perform RSA verification
with two essential parameters for a RSA public key in contract of
rsa_verify_with_keynode(), which requires additional three parameters
stored in FIT image.

It will be used in implementing UEFI secure boot, i.e. image authentication
and variable authentication.

Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

In the current implementation of FIT_SIGNATURE, five parameters for
a RSA public key are required while only two of them are essential.
(See rsa-mod-exp.h and uImage.FIT/signature.txt)
This is a result of considering relatively limited computer power
and resources on embedded systems, while such a assumption may not
be quite practical for other use cases.

In this patch, added is a function, rsa_gen_key_prop(), which will
generate additional parameters for other uses, in particular
UEFI secure boot, on the fly.

Note: the current code uses some "big number" routines from BearSSL
for the calculation.

Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>

In the next couple of commits, under new CONFIG_RSA_VERIFY_WITH_PKEY,
rsa_verify() will be extended to be able to perform RSA decryption without
additional RSA key properties from FIT image, i.e. rr and n0inv.

Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>