u-boot.git/nand_spl, branch v2009.01

Align end of bss by 4 bytes

2008-11-18T22:13:16+00:00

Most of the bss initialization loop increments 4 bytes
at a time. And the loop end is checked for an 'equal'
condition. Make the bss end address aligned by 4, so
that the loop will end as expected.

Signed-off-by: Selvamuthukumar 
Signed-off-by: Wolfgang Denk

Make Freescale local bus registers available for both 83xx and 85xx.

2008-10-29T16:12:53+00:00

- Rename lbus83xx_t to fsl_lbus_t and move it to asm/fsl_lbc.h so that it
  can be shared by both 83xx and 85xx
- Remove lbus83xx_t and replace it with fsl_lbus_t in all 83xx boards
  files which use lbus83xx_t.
- Move FMR, FIR, FCR, FPAR, LTESR from mpc83xx.h to asm/fsl_lbc.h so that
  85xx can share them.

Signed-off-by: Jason Jin 
Signed-off-by: Haiying Wang 
Signed-off-by: Scott Wood

rename CFG_ macros to CONFIG_SYS

2008-10-18T19:54:03+00:00

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD

ARM: Add support for S3C6400 based SMDK6400 board

2008-08-30T22:39:47+00:00

SMDK6400 can only boot U-Boot from NAND-flash. This patch adds a nand_spl
driver for it too. The board can also boot from the NOR flash, but due to
hardware limitations it can only address 64KiB on it, which is not enough
for U-Boot. Based on the original sources by Samsung for U-Boot 1.1.6.

Signed-off-by: Guennadi Liakhovetski

NAND: Remove delay from nand_boot_fsl_elbc.c.

2008-08-21T18:44:17+00:00

It was for debugging purposes, and shouldn't have been left in.

Signed-off-by: Scott Wood

Coding Style cleanup, update CHANGELOG

2008-08-14T12:41:06+00:00

Signed-off-by: Wolfgang Denk

nand_spl: Support page-aligned read in nand_load, use chipselect

2008-08-12T16:31:32+00:00

Supporting page-aligned reads doesn't incure any sinificant overhead, just
a small change in the algorithm. Also replace in_8 with readb, since there
is no in_8 on ARM.

Signed-off-by: Guennadi Liakhovetski 
Signed-off-by: Scott Wood

NAND boot: Update large page support for current API.

2008-08-12T16:31:31+00:00

Also, remove the ctrl variable in favor of passing the constants
directly, and remove redundant (u8) casts.

Signed-off-by: Scott Wood

NAND boot: MPC8313ERDB support

2008-08-12T16:31:31+00:00

Note that with older board revisions, NAND boot may only work after a
power-on reset, and not after a warm reset.  I don't have a newer board
to test on; if you have a board with a 33MHz crystal, please let me know
if it works after a warm reset.

Signed-off-by: Scott Wood

NAND: Update nand_spl driver to match updated nand subsystem

2008-08-12T16:31:23+00:00

This patch changes the NAND booting driver nand_spl/nand_boot.c to match
the new infrastructure from the updated NAND subsystem. This NAND
subsystem was recently synced again with the Linux 2.6.22 MTD/NAND
subsystem.

Signed-off-by: Stefan Roese