u-boot.git/net/eth-uclass.c, branch v2019.07

net: eth-uclass: Support device tree MAC addresses

2019-06-01T18:33:17+00:00

Add the standard Ethernet device tree bindings (imported from v5.0 of
the Linux kernel) and implement support for reading the MAC address for
Ethernet devices in the Ethernet uclass. If the "mac-address" property
exists, the MAC address will be parsed from that. If that property does
not exist, the "local-mac-address" property will be tried as fallback.

MAC addresses from device tree take precedence over the ones stored in
a network interface card's ROM.

Acked-by: Joe Hershberger 
Reviewed-by: Grygorii Strashko 
Signed-off-by: Thierry Reding

net: eth-uclass: Write MAC address to hardware after probe

2019-06-01T18:33:16+00:00

In order for the device to use the proper MAC address, which can have
been configured in the environment prior to the device being registered,
ensure that the MAC address is written after the device has been probed.
For devices that are registered before the network stack is initialized,
this is already done during eth_initialize(). If the Ethernet device is
on a bus that is not initialized on early boot, such as PCI, the device
is not available at the time eth_initialize() is called, so we need the
MAC address programming to also happen after probe.

Acked-by: Joe Hershberger 
Signed-off-by: Thierry Reding

net: remove CONFIG_MCAST_TFTP

2019-01-24T17:35:30+00:00

No mainline board enables CONFIG_MCAST_TFTP and there have been
compilation issues with the code for some time. Additionally, it has a
potential buffer underrun issue (reported as a side note in
CVE-2018-18439).

Remove the multicast TFTP code but keep the driver API for the future
addition of IPv6.

Cc: Simon Goldschmidt 
Signed-off-by: Chris Packham 
Acked-by: Joe Hershberger

net: eth-uclass: Fix for DM USB ethernet support

2018-08-21T14:21:37+00:00

When a USB ethernet device is halted, the device driver is removed. When
this happens the uclass private memory is freed and uclass_priv is set to
NULL. This causes a data abort when uclass_priv->state is then set to
ETH_STATE_PASSIVE.

Fix it by checking if uclass_priv is NULL before setting uclass_priv->state

Signed-off-by: Jean-Jacques Hiblot 
Acked-by: Joe Hershberger

net: Only call halt on a driver that has been init'ed

2018-07-26T19:08:17+00:00

With driver model, we were not checking if the state of the device was
marked as active before calling the halt function. Check that the device
is probed and also marked as active. This avoids the case where we were
calling halt on the first device in net_init() and the driver would
operate on bogus data structures causing problems. In this case, the
priv was all 0, so halt() would close STDIN.

Signed-off-by: Joe Hershberger 
Reviewed-by: Simon Glass

net: Initialize as many ethernet devices as possible

2018-06-13T18:54:15+00:00

On devices that have their first network interface provided by a FPGA,
the initialization of further interfaces will fail if the FPGA is not
yet programmed. This leads to problems during factory setup when the
data is supposed to be loaded over secondary netowork interfaces.

To avoid this, use the uclass_{first,next}_device_check functions to
initialize as many ethernet devices as possible.

Signed-off-by: Mario Six 
Acked-by: Joe Hershberger

SPDX: Convert all of our single license tags to Linux Kernel style

2018-05-07T13:34:12+00:00

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini

net: Only access network devices after init

2018-03-22T20:05:31+00:00

In the efi_loader main loop we call eth_rx() occasionally. This rx function
might end up calling into devices that haven't been initialized yet,
potentially resulting in a lot of transfer timeouts.

Instead, let's make sure the ethernet device is actually initialized before
reading from or writing to it.

Signed-off-by: Alexander Graf 
Acked-by: Joe Hershberger

env: Rename eth_getenv_enetaddr() to eth_env_get_enetaddr()

2017-08-16T12:30:44+00:00

Rename this function for consistency with env_get().

Signed-off-by: Simon Glass

env: Rename getenv/_f() to env_get()

2017-08-16T12:30:24+00:00

We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.

Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.

Suggested-by: Wolfgang Denk 
Signed-off-by: Simon Glass