Use IS_ENABLED() instead, to reduce the number of build paths.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

This converts the following to Kconfig:
   CONFIG_BOOTP_SERVERIP

Signed-off-by: Simon Glass <sjg@chromium.org>

This converts the following to Kconfig:
   CONFIG_TIMESTAMP

Signed-off-by: Simon Glass <sjg@chromium.org>

This converts the following to Kconfig:
   CONFIG_UDP_CHECKSUM

Signed-off-by: Simon Glass <sjg@chromium.org>

This converts the following to Kconfig:
   CONFIG_KEEP_SERVERADDR

Drop the preprocessor usage also.

Signed-off-by: Simon Glass <sjg@chromium.org>

Pull request doc-2022-04-rc1

Replace @return by Return: in code comments.

Sphinx expects Return: and not @return to indicate a return value.

find . -name '*.c' -exec \
sed -i 's/^\(\s\)\*\(\s*\)@return\(\s\)/\1*\2Return:\3/' {} \;

find . -name '*.h' -exec \
sed -i 's/^\(\s\)\*\(\s*\)@return\(\s\)/\1*\2Return:\3/' {} \;

Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>

Xilinx changes for v2022.04-rc1

gpio:
- Add modepin driver

net:
- Save random mac addresses to eth variable

zynqmp gem:
- Add support for mdio bus DT description
- Add support for reset and SGMII phy configuration
- Reduce timeout for MDIO accesses

zynqmp clk:
- Fix clock handling for gem and usb

phy:
- Add zynqmp phy/serdes driver

serial:
- Add one missing compatible string

microblaze:
- Symbol alignement
- SPL fixups
- Code cleanups

zynqmp:
- Various dt changes, DP pre-reloc, gem resets, gem clocks
- Switch SOM to shared psu configuration
- Move dcache handling to firmware driver
- Workaround gmii2rgmii DT description issue
- Enable broadcasts again
- Change firmware enablement logic
- Small adjustement in firmware driver

versal:
- Support new mmc@ DT nodes
- Fix run time variable handling
- Add missing I2C_PMC ID for power domain

The fastboot protocol uses per default the UDP port 5554. In some cases
it might be needed to change the used port. The fastboot utility provides
a way to specifiy an other port number to use already.

  fastboot -s udp:192.168.1.76:1234 boot fastboot.img

Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

If the DSA API is going to allow drivers to do things such as:

- phy_config in dsa_ops :: port_probe
- phy_startup in dsa_ops :: port_enable

then it would actually be good if the ->port_probe() method would
actually be called in all cases before the ->port_enable() is.

Currently this is true for user ports, but not true for the CPU port,
because the CPU port does not have a udevice registered for it (this is
all part of DSA's design). So the current issue is that after
phy_startup has finished for the CPU port, its phydev->speed is an
uninitialized value, because phy_config() was never called for the
priv->cpu_port_fixed_phy, and it is precisely phy_config() who copies
the speed into the phydev in the case of the fixed PHY driver.

So we need to simulate a probing event for the CPU port by manually
calling the driver's ->port_probe() method for the CPU port.

Fixes: 8a2982574854 ("net: dsa: introduce a .port_probe() method in struct dsa_ops")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>