This can be used for device tree size reduction similar as
CONFIG_OF_SPL_REMOVE_PROPS option. Some boards must pass the
built-in DTB unchanged to the kernel, thus we may not cut it
down unconditionally. Therefore enable the property removal
list option only if CONFIG_OF_DTB_PROPS_REMOVE is selected.

Signed-off-by: Anatolij Gustschin <agust@denx.de>

In order to apply an overlay to a DTB. The DTB must have been generated
with the option '-@'.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

When device-tree compilation fails it is sometimes tricky to see which
line is broken, since the input file to dtc is a pre-processed version
of the device tree.

Add a line that points to the file that needs to be checked:

When the error is in the main .dts file, output is something like this:

   output: 'Error: arch/x86/dts/.chromebook_coral.dtb.pre.tmp:478.46-47
	syntax error
   FATAL ERROR: Unable to parse input tree

but in fact looking at that file shows nothing useful:

   PAD_CFG_NF_IOSSTATE_IOSTERM(GPIO_157, UP_20K, DEEP, NF1, HIZCRX1, DISPUPD)

Instead we need to look at the preprocessed file, which shows:

   163 ((1U << 30) | (1 << 10)) ((0xb << 10) | PAD_CFG1_IOSSTATE_HIZCRX1)

Here it is clear that PAD_CFG1_IOSSTATE_HIZCRX1 is not defined and so is
not being resolved by the preprocessor.

This commit adds an additional useful message:

   Check arch/x86/dts/.chromebook_coral.dtb.dts.tmp for errors

Note that if the error is reported in an included file, such as
u-boot.dtsi then the output is the following:

   Error: arch/x86/dts/u-boot.dtsi:137.14-15 syntax error
   FATAL ERROR: Unable to parse input tree

But again, if the error is due to a preprocessor failure, like this:

   filename = CONFIG_IFW_INPUT_FILE;

then you can't tell what the problem is by looking at the source. All you
see is the original code:

	intel-ifwi {
		filename = CONFIG_IFW_INPUT_FILE;
		...
		};
	};
	intel-fsp-m {
		filename = CONFIG_FSP_FILE_M;
	};

Everything looks fine. But looking at the output of the preprocessor:

 intel-ifwi {
  filename = CONFIG_IFW_INPUT_FILE;
  ...
 };
 intel-fsp-m {
  filename = "fsp_m.bin";
 };

This shows that the filename (normally "fitimage.bin") has not been
inserted the preprocess, leading to the realisation that the value should
be CONFIG_IFWI_INPUT_FILE.

If the above does not make sense, I encourage people to try introducing
errors in the device tree preprocessed values.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

At present the iasl tool (Intel ACPI (Advanced Configuration and Power
Interface) Source Language Compiler) is called in such a way that it uses
the source directory for its temporary files.

This means we end up with these files when building x86 boards:

   board/dfi/dfi-bt700/dsdt.aml
   board/dfi/dfi-bt700/dsdt.asl.tmp

Update the code to put temporary files in the target directory instead.

The iasl tool is quite confusing since it generates files with different
extensions and does not allow these to be individually specified. Add some
documentation to help with this.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: remove dsdt.hex from 'make clean' rules and correct U-Boot spelling]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>

When changing the architecture without calling 'make clean' a subsequent
make fails with
lib/efi_loader/efi_crt0.o: file not recognized: File format not recognized

Force efi_crt0.o to be always rebuild.

Reported-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

We can remove the pre reloc property in SPL and TPL device-tree:
- u-boot,dm-pre-reloc
- u-boot,dm-spl
- u-boot,dm-tpl
As only the needed node are kept by fdtgrep (1st pass).

The associated function (XXX_pre_reloc) are simple for SPL/TPL:
return always true.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>

Since commit f51a226436a87 ("efi_loader: provide freestanding library") in
parallel builds errors

    lib/efi_selftest/../efi_loader/efi_freestanding.o:
    file not recognized: File truncated

occur. Obviously make cannot correctly sequence parallel builds with a
dependency like ../efi_loader/efi_freestanding.o.

Fixes: f51a226436a87 ("efi_loader: provide freestanding library")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

*.dts are processed using a custom command, then the C pre-processor is
run on them, then they are compiled using dtc. Thus, the dependency
files generated by both cpp and dtc reference a temporary file name
rather than the actual source file. While this information isn't used
for any purpose by the build system, and hence this causes no functional
issue, it does cause the dependency files to contain invalid and
confusing data, which is unhelpful while debugging build problems. Fix
this using sed.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Take the first prerequisite (dts overlay file) instead of standard
input.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Symbolic links are not supported on all file systems, e.g. not on FAT. So
it is not wise to use them in our source tree.

Use a qualified path to refer to lib/efi_loader/efi_freestanding.c in
scripts/Makefile.lib instead.

Reported-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[agraf: Fix build with O=]
Signed-off-by: Alexander Graf <agraf@suse.de>