- Bug fixes and updates on ls2088a,ls1028a, ls1046a, ls1043a, ls1012a - lx2-watchdog support - layerscape: pci-endpoint support, spin table relocation fixes and cleanups - fsl-crypto: RNG support and bug fixes
binman support for FIT new UCLASS_SOC patman switch 'test' command minor fdt fixes patman usability improvements
The eSDHC adapter card identification and multiplexing configuration through FPGA had been implemented in both common mmc driver and fsl_esdhc driver. However it is proper to move these code to board files and do it during board initialization. The FPGA registers are also board specific. This patch is to move eSDHC adapter card identification and multiplexing configuration from mmc driver to specific board files. And the option CONFIG_FSL_ESDHC_ADAPTER_IDENT is no longer needed. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> [Rebased, Removed T1040QDS change as board does not exist] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add Kconfig entries for the dc2114x driver and convert various boards. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Ramon Fried <rfried.dev@gmail.com>
If the pylibfdt shared-object file is detected, then Python assumes that the libfdt.py file exists also. Sometimes when an incremental build aborts, the shared-object file is built but the libfdt.py is not. The only way out at this point is to use 'make mkproper', or similar. Fix this by removing the .so file before it is built. This seems to make Python rebuild everything. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This reverts commit 5d3a21df6694ebd66d5c34c9d62a26edc7456fc7, reversing changes made to 56d37f1c564107e27d873181d838571b7d7860e7. Unfortunately this is causing CI failures: https://travis-ci.org/github/trini/u-boot/jobs/711313649 Signed-off-by: Tom Rini <trini@konsulko.com>
If the pylibfdt shared-object file is detected, then Python assumes that the libfdt.py file exists also. Sometimes when an incremental build aborts, the shared-object file is built but the libfdt.py is not. The only way out at this point is to use 'make mkproper', or similar. Fix this by removing the .so file before it is built. This seems to make Python rebuild everything. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch adds very basic support for the Octeon III SoCs. Only CFI parallel NOR flash and UART is supported for now. Please note that the basic Octeon port does not include the DDR3/4 initialization yet. This will be added in some follow-up patches later. To still use U-Boot on with this port, the L2 cache (4MiB on Octeon III CN73xx) is used as RAM. This way, U-Boot can boot to the prompt on such boards. Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
When fixdep detects CONFIG_IS_ENABLED and other similar macros, it must
parse the macro parameter to determine which actual CONFIG_ option is
being referenced. This involves moving a pointer forward through the
entire CONFIG_ option "word". Currently, the code uses variable q to walk
through the word, but doesn't actually initialize it to point at the
parameter before doing so. Consequently, the walking process immediately
fails since it sees the macro invocatoins's ( rather than the expected
alpha-numeric characters in the macro parameter. Fix this by adding the
missing initialization.
Fixes: 67f2ee86ccbe ("kbuild: fixdep: Resync this with v4.17")
Fixes: 7012865e961c ("gpio: fix test.py for gpio label lookup")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since commit 4b0bcfa7c4ec (Kconfig: Migrate CONFIG_BOOTM_* options), the config_defaults.h file has been void of any actual content - and these days, "sane defaults for everyone" is achieved by appropriate default values in Kconfig. Remove it, and thus make every translation unit process one less header file. Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>