u-boot.git/test/cmd/Makefile, branch v2023.04

cmd: Add a SEAMA image load command

2023-02-06T22:10:15+00:00

Add a command to load SEAMA (Seattle Image), a NAND flash
on-flash storage format.

This type of flash image is found in some D-Link routers such
as DIR-645, DIR-842, DIR-859, DIR-860L, DIR-885L, DIR890L and
DCH-M225, as well as in WD and NEC routers on the ath79
(MIPS), Broadcom BCM53xx, and RAMIPS platforms.

This U-Boot command will read and decode a SEAMA image from
raw NAND flash on any platform. As it is always using big endian
format for the data decoding is always necessary on platforms
such as ARM.

The command is needed to read a SEAMA-encoded boot image on the
D-Link DIR-890L router for boot from NAND flash in an upcoming
port of U-Boot to the Broadcom Northstar (BCM4709, BCM53xx)
architecture.

A basic test and documentation is added as well. The test must
be run on a target with NAND flash support and at least one
resident SEAMA image in flash.

Cc: Rafał Miłecki 
Signed-off-by: Linus Walleij

test: cmd: exit: Add unit test for exit and partly run commands

2023-01-11T20:02:24+00:00

Add a test which validates that exit from environment script works as
expected, including return value propagation and clipping to positive
integers.

Reviewed-by: Simon Glass 
Signed-off-by: Marek Vasut

test: cmd: add test for wget command.

2022-11-28T18:06:40+00:00

Simulate a TCP HTTP server's response for testing wget command.

Signed-off-by: Ying-Chun Liu (PaulLiu) 
Cc: Christian Gmeiner 
Cc: Joe Hershberger 
Cc: Michal Simek 
Cc: Ramon Fried 
Cc: Simon Glass 
Reviewed-by: Simon Glass 
Reviewed-by: Ramon Fried

video: Add commands to list and change fonts

2022-10-30T19:01:40+00:00

Add a new 'font' command which allows the fonts to be listed as well as
selecting a different font and size.

Allow the test to run on sandbox, where multiple font/size combinations
are supported, as well as sandbox_flattree, where they are not.

Signed-off-by: Simon Glass

test: run setexpr test only on sandbox

2022-10-12T12:56:24+00:00

The test relies on memory being available at 0x0. This in not valid for
many boards.

Signed-off-by: Heinrich Schuchardt 
Reviewed-by: Simon Glass

test: cmd: add test for temperature command

2022-10-11T20:03:04+00:00

Add simple test for the temperature command.

Signed-off-by: Robert Marko 
Reviewed-by: Simon Glass

cmd: Add pause command

2022-09-02T17:40:42+00:00

This command is being introduced with the goal of allowing user-friendly
"generic use case" U-Boot builds to pause until user input under some
situations.

The main use case would be when a boot failure happens, to pause until
the user has had time to acknowledge the current state.

Tested using:

    make && ./u-boot -v -T -c 'ut lib lib_test_hush_pause'

Signed-off-by: Samuel Dionne-Riel 
Cc: Simon Glass

fdt: Start a test for the fdt command

2022-07-26T08:30:56+00:00

Add a basic test of the 'fdt addr' command, to kick things off.

This includes a new convenience function to run a command from a printf()
string.

Signed-off-by: Simon Glass

cmd: load: add load command for memory mapped

2022-06-22T15:35:47+00:00

cp.b is used a lot as a way to load binaries to memory and execute
them, however we may need to integrate this with the efi subsystem to
set it up as a bootdev.

So, introduce a loadm command that will be consistent with the other
loadX commands and will call the efi API's.

ex: loadm $kernel_addr $kernel_addr_r $kernel_size

with this a kernel with CONFIG_EFI_STUB enabled will be loaded and
then subsequently booted with bootefi command.

Signed-off-by: Rui Miguel Silva 
Reviewed-by: Tom Rini

cmd: pinmux: support pin name in status command

2021-07-23T11:13:25+00:00

Allow pin name parameter for pimux staus command,
as gpio command to get status of one pin.

The possible usage of the command is:

> pinmux dev pinctrl
> pinmux status

> pinmux status -a

> pinmux status 

Signed-off-by: Patrick Delaunay 
Reviewed-by: Simon Glass