Add a command to load SEAMA (Seattle Image), a NAND flash on-flash storage format. This type of flash image is found in some D-Link routers such as DIR-645, DIR-842, DIR-859, DIR-860L, DIR-885L, DIR890L and DCH-M225, as well as in WD and NEC routers on the ath79 (MIPS), Broadcom BCM53xx, and RAMIPS platforms. This U-Boot command will read and decode a SEAMA image from raw NAND flash on any platform. As it is always using big endian format for the data decoding is always necessary on platforms such as ARM. The command is needed to read a SEAMA-encoded boot image on the D-Link DIR-890L router for boot from NAND flash in an upcoming port of U-Boot to the Broadcom Northstar (BCM4709, BCM53xx) architecture. A basic test and documentation is added as well. The test must be run on a target with NAND flash support and at least one resident SEAMA image in flash. Cc: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The font help has an incorrect newline. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: cdd964e3801 ("test: Tidy up help for ut command")
Add a test which validates that exit from environment script works as expected, including return value propagation and clipping to positive integers. Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Marek Vasut <marex@denx.de>
When running unit tests, some may have side effects which cause a subsequent test to break. This can sometimes be seen when using 'ut dm' or similar. Add a new argument which allows a particular (failing) test to be run immediately after a certain number of tests have run. This allows the test causing the failure to be determined. Update the documentation also. Signed-off-by: Simon Glass <sjg@chromium.org>
Add a 'ut info' command to show the number of suites and tests. This is useful to get a feel for the scale of the tests. Signed-off-by: Simon Glass <sjg@chromium.org>
Sort this and put the command summary at the top instead of the bottom. Adjust it so that the newlines are at the start of the strings, so that there is not a blank line at the end. Signed-off-by: Simon Glass <sjg@chromium.org>
At present we normally write tests either in Python or in C. But most Python tests end up doing a lot of checks which would be better done in C. Checks done in C are orders of magnitude faster and it is possible to get full access to U-Boot's internal workings, rather than just relying on the command line. The model is to have a Python test set up some things and then use C code (in a unit test) to check that they were done correctly. But we don't want those checks to happen as part of normal test running, since each C unit tests is dependent on the associate Python tests, so cannot run without it. To acheive this, add a new UT_TESTF_MANUAL flag to use with the C 'check' tests, so that they can be skipped by default when the 'ut' command is used. Require that tests have a name ending with '_norun', so that pytest knows to skip them. Signed-off-by: Simon Glass <sjg@chromium.org>
Add a new 'font' command which allows the fonts to be listed as well as selecting a different font and size. Allow the test to run on sandbox, where multiple font/size combinations are supported, as well as sandbox_flattree, where they are not. Signed-off-by: Simon Glass <sjg@chromium.org>
The test relies on memory being available at 0x0. This in not valid for many boards. Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Some tests can have race conditions which are hard to detect on a single one. Add a way to run tests more than once, to help with this. Each individual test is run the requested number of times before moving to the next test. If any runs failed, a message is shown. This is most useful when running a single test, since running all tests multiple times can take a while. Signed-off-by: Simon Glass <sjg@chromium.org>