u-boot.git/test/dm, branch v2015.07

dm: pci: Allow PCI bus numbering aliases

2015-06-04T09:34:47+00:00

Commit 9cc36a2 'dm: core: Add a flag to control sequence numbering' changed
the default uclass behaviour to not support bus numbering. This is incorrect
for PCI and that commit should have enabled the flag for PCI.

Enable it so that PCI buses can be found and the 'pci' command works again.
Also add a test for this.

Signed-off-by: Simon Glass

test: dm: Recover the driver model tree after tests

2015-05-21T13:16:18+00:00

Put the driver model for the system back into a good state after
completing the DM testing.

Signed-off-by: Joe Hershberger 
Acked-by: Simon Glass

test: dm: eth: Handle failed test env cleanup

2015-05-21T13:16:17+00:00

Make sure that the env gets cleaned up after a test fails so that other
tests aren't affected.

Signed-off-by: Joe Hershberger

test: dm: Don't bail on all tests if one test fails

2015-05-21T13:16:17+00:00

There's not much point in having a failure count if we always give up on
the first failure. Also stop clearing the entire state between tests.

Make sure that any failures are still passed out to the command line.

Signed-off-by: Joe Hershberger 
Reviewed-by: Simon Glass

test: Move the unit tests to their own menu

2015-05-21T13:16:17+00:00

Make all unit tests selectable as a menu of test suites instead of just
sitting in the top-level menu individually.

Signed-off-by: Joe Hershberger 
Acked-by: Simon Glass

test: dm: Move the dm tests over to the ut command

2015-05-21T13:16:17+00:00

Unify the command for running unit tests further by moving the "dm test"
command over to "ut dm".

Signed-off-by: Joe Hershberger 
Acked-by: Simon Glass

test: Generalize the unit test framework

2015-05-21T13:16:16+00:00

Separate the ability to define tests and assert status of test functions
from the dm tests so they can be used more consistently throughout all
tests.

Signed-off-by: Joe Hershberger 
Reviewed-by: Simon Glass

net: Apply default format rules to all ethaddr

2015-05-21T13:13:20+00:00

Use a regular expression to apply the default formatting flags for all
ethaddr env vars.

Signed-off-by: Joe Hershberger 
Reviewed-by: Simon Glass

test: dm: test.dts - move to sandbox dts directory

2015-05-15T01:59:07+00:00

The file test.dts from driver model test directory,
was compiled by call dtc in script: test/dm/test-dm.sh.

This doesn't allow for including of dtsi files and using
of C preprocessor routines in this dts file.

Since the mentioned script builds U-Boot before tests,
then moving the test.dts file into sandbox dts directory
is reasonable.

Signed-off-by: Przemyslaw Marczak 
Acked-by: Simon Glass 
Tested on sandbox:
Tested-by: Simon Glass

test: dm: add sandbox PMIC framework tests

2015-05-15T01:58:34+00:00

This change adds new file to sandbox driver model test environment.
The file is: test/dm/power.c, and it includes tests for PMIC framework,
which includes PMIC uclass and REGULATOR uclass.

All tests are based od Sandbox PMIC emulated device. Some test constants for
this device are defined in the header: include/power/sandbox_pmic.h

PMIC tests includes:
- pmic get - tests, that pmic_get() returns the requested device
- pmic I/O - tests I/O by writing and reading some values to PMIC's registers
             and then compares, that the write/read values are equal.

The regulator tests includes:
- Regulator get by devname/platname
- Voltage set/get
- Current set/get
- Enable set/get
- Mode set/get
- Autoset
- List autoset

For the regulator 'get' test, the returned device pointers are compared,
and their names are also compared to the requested one.
Every other test, first sets the given attribute and next try to get it.
The test pass, when the set/get values are equal.

Signed-off-by: Przemyslaw Marczak 
Acked-by: Simon Glass 
Tested on sandbox:
Tested-by: Simon Glass