We know this is U-Boot so the prefix serves no purpose other than to
make things longer and harder to read. Drop it and rename the files.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # test_android / test_dfu

This fixture name is quite long and results in lots of verbose code.
We know this is U-Boot so the 'u_boot_' part is not necessary.

But it is also a bit of a misnomer, since it provides access to all the
information available to tests. It is not just the console.

It would be too confusing to use con as it would be confused with
config and it is probably too short.

So shorten it to 'ubman'.

Signed-off-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/u-boot/CAFLszTgPa4aT_J9h9pqeTtLCVn4x2JvLWRcWRD8NaN3uoSAtyA@mail.gmail.com/

At present test_pinmux_status() assumes that test_pinmux_dev() has run
beforehand. Drop this assumption so we can run the tests in parallel.

Signed-off-by: Simon Glass <sjg@chromium.org>

Update the result of do_status and always returns a CMD_RET_ value
(-ENOSYS was a possible result of show_pinmux).

This patch also adds pincontrol name in error messages (dev->name)
and treats correctly the status sub command when pin-controller device is
not selected.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

This extends the pinctrl-sandbox driver to support pin muxing, and adds a
test for that behaviour. The test is done in C and not python (like the
existing tests for the pinctrl uclass) because it needs to call
pinctrl_select_state.  Another option could be to add a command that
invokes pinctrl_select_state and then test everything in
test/py/tests/test_pinmux.py.

The pinctrl-sandbox driver now mimics the way that many pinmux devices
work.  There are two groups of pins which are muxed together, as well as
four pins which are muxed individually. I have tried to test all normal
paths. However, very few error cases are explicitly checked for.

Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Add a simple pincontrol associated to the sandbox gpio driver,
that allows to check pin configuration with the command pinmux.

The pinmux test is also updated to test behavior with 2 pincontrols.

Example to check LED pin configuration:

=> pinmux list
| Device                        | Driver                        | Parent
| pinctrl-gpio                  | sandbox_pinctrl_gpio          | root_driver
| pinctrl                       | sandbox_pinctrl               | root_driver

=> pinmux dev pinctrl-gpio

=> pinmux status

a0        : gpio input .
a1        : gpio input .
a2        : gpio input .
a3        : gpio input .
a4        : gpio input .
a5        : gpio output .
a6        : gpio output .
...

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>

Add test for "pins" configuration in gpio uclass with set_state() ops
and test for generic parsing of pinconf_param array).

set_state() is called by:
- pinctrl_generic_set_state
 |- pinctrl_generic_set_state_subnode

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Add pinmux test which test the following commands:
  - pinmux list
  - pinmux dev
  - pinmux status

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Mark some tests as sandbox-centric]
Signed-off-by: Tom Rini <trini@konsulko.com>

Signed-off-by: Tom Rini <trini@konsulko.com>