u-boot.git/test, branch v2023.04-rc2

reset: Allow reset_get_by_name() with NULL name

2023-02-12T18:44:20+00:00

This allows devm_reset_control_get(dev, NULL) to work and get the first
reset control, which is common in code ported from Linux.

Signed-off-by: Samuel Holland 
Reviewed-by: Simon Glass 
Link: https://lore.kernel.org/r/20230122000252.53642-2-samuel@sholland.org

clk: Allow clk_get_by_name() with NULL name

2023-02-12T18:44:20+00:00

This allows devm_clock_get(dev, NULL) to work and get the first clock,
which is common in code ported from Linux.

Signed-off-by: Samuel Holland 
Reviewed-by: Sean Anderson 
Reviewed-by: Simon Glass 
Link: https://lore.kernel.org/r/20230122000252.53642-1-samuel@sholland.org

trace: Add a test

2023-02-11T17:22:35+00:00

Add a test which runs sandbox, collects a trace and makes sure it can
be processed by trace-cmd. This should ensure that this feature continues
to work as U-Boot and trace-cmd evolve.

Signed-off-by: Simon Glass

dm: button: add support for linux_code in button-gpio.c driver

2023-02-10T17:50:01+00:00

Linux event code must be used in input devices, using buttons.

Signed-off-by: Dzmitry Sankouski 
Reviewed-by: Simon Glass

test: create dedicated fdt node for ofnode_for_each_prop test

2023-02-10T17:50:01+00:00

Property count may change in /buttons node, if more button tests added,
and this will break ofnode_for_each_prop.
Add separate node for mentioned test.

Signed-off-by: Dzmitry Sankouski 
Reviewed-by: Simon Glass

test: lmb: Rework lib_test_lmb_max_regions test to scale

2023-02-08T19:09:39+00:00

First, this test depends on CONFIG_LMB_USE_MAX_REGIONS, so add that as a
test before building. Second, instead of using a hard-coded value of 8,
which is the default of CONFIG_LMB_USE_MAX_REGIONS previously, use that
directly and update the comments. The only trick here is that one part
of the test itself also was written with the value of 8 itself in mind.
Rework the size of the lmb region we allocate to scale with the value of
CONFIG_LMB_USE_MAX_REGIONS.

Cc: Simon Glass 
Signed-off-by: Tom Rini 
Reviewed-by: Simon Glass

cmd: Add a SEAMA image load command

2023-02-06T22:10:15+00:00

Add a command to load SEAMA (Seattle Image), a NAND flash
on-flash storage format.

This type of flash image is found in some D-Link routers such
as DIR-645, DIR-842, DIR-859, DIR-860L, DIR-885L, DIR890L and
DCH-M225, as well as in WD and NEC routers on the ath79
(MIPS), Broadcom BCM53xx, and RAMIPS platforms.

This U-Boot command will read and decode a SEAMA image from
raw NAND flash on any platform. As it is always using big endian
format for the data decoding is always necessary on platforms
such as ARM.

The command is needed to read a SEAMA-encoded boot image on the
D-Link DIR-890L router for boot from NAND flash in an upcoming
port of U-Boot to the Broadcom Northstar (BCM4709, BCM53xx)
architecture.

A basic test and documentation is added as well. The test must
be run on a target with NAND flash support and at least one
resident SEAMA image in flash.

Cc: Rafał Miłecki 
Signed-off-by: Linus Walleij

arm: qemu: Move GUIDs to the C file

2023-02-06T18:04:53+00:00

These are only used in one place, so move them there.

Signed-off-by: Simon Glass

test: bootdev: Do not require USB to compile test

2023-02-06T18:04:52+00:00

This test will block compilation of the entire test suite
on platforms without USB support. Make the extern
"usb_started" conditional on USB host or gadget and
define a dummy flag if neither is enabled.

Cc: Simon Glass 
Signed-off-by: Linus Walleij 
Reviewed-by: Simon Glass

test: dm: test-fdt: Add decode_panel_timing test

2023-02-04T17:15:14+00:00

To test decode_panel_timing add a panel-timings node
and a DM test for decode panel timingd by matching
the panel timing node parameters.

Signed-off-by: Nikhil M Jain 
Reviewed-by: Simon Glass