u-boot.git/tools/Makefile, branch v2014.07-rc3

tools: refactor HOSTLOADLIBES_* options

2014-06-05T21:01:59Z

The tools mkimage, dumpimage, fit_info, fit_check_sign always have the common libraries to be linked, so HOSTLOADLIBES_* can be consolidated a little bit. Signed-off-by: Masahiro Yamada Acked-by: Simon Glass

mkimage : Split out and clean pbl_crc32 for use by other image types

2014-06-05T18:38:38Z

The crc32 used by pblimgae is NOT the same as zlib crc32. The pbl_crc32 is useful for other purposes in mkimage so split it out. While we are about it, clean up redundant and confusing code. Signed-off-by: Charles Manning

arm:at91: enable ROM loadable atmel image

2014-05-26T22:10:49Z

For sama5d3xek we need to modify the SPL image for correct detection by ROM code. Signed-off-by: Andreas Bießmann Tested-by: Bo Shen

mkimage: add atmelimage

2014-05-26T22:10:48Z

The new atmelimage converts a machine code BLOB to bootable ROM image. Atmel ROM has no sophisticated image format, it only checks the first 7 ARM vectors. The vectors can contain valid B or LDR opcodes, the 6'th vector contains the image size to load. Additionally the PMECC header can be written by the atmelimage target. The parameters must be given via the -n switch as a coma separated list. For example: mkimage -T atmelimage \ -n usePmecc=1,sectorPerPage=4,sectorSize=512,spareSize=64,eccBits=4,eccOffset=36 \ -d spl/u-boot-spl.bin boot.bin A provided image can be checked for correct header setup. It prints out the PMECC header parameters if it has one and the 6'th interrupt vector content. ---8<--- Image Type: ATMEL ROM-Boot Image with PMECC Header PMECC header ==================== eccOffset: 36 sectorSize: 512 eccBitReq: 4 spareSize: 64 nbSectorPerPage: 4 usePmecc: 1 ==================== 6'th vector has 17044 set --->8--- A SPL binary modified with the atmelimage mkimage target was succesfully booted on a sama5d34ek via MMC and NAND. Signed-off-by: Andreas Bießmann Cc: Bo Shen Cc: Heiko Schocher Tested-by: Bo Shen

sunxi: non-FEL SPL boot support for sun7i

2014-05-25T14:31:03Z

Add support for booting from an MMC card. Signed-off-by: Stefan Roese Signed-off-by: Henrik Nordström Signed-off-by: Ian Campbell Reviewed-by: Marek Vasut Cc: Tom Cubie Reviewed-by: Tom Rini

Merge branch 'u-boot/master'

2014-05-09T09:50:14Z

Conflicts: drivers/net/Makefile (trivial merge)

tools: fix Makefile to clean-up fit_info and fit_check_sign

2014-04-18T14:42:29Z

We should avoid the description in Makefile like this ifdef CONFIG_FIT_SIGNATURE hostprogs-y += fit_info$(SFX) fit_check_sign$(SFX) endif Otherwise, fit_info and fit_check_sign would never be cleaned by "make clean". Signed-off-by: Masahiro Yamada Cc: Heiko Schocher

tools: mkimage: add support for gpimage format

2014-04-17T21:24:38Z

This patch add support for gpimage format as a preparatory patch for porting u-boot for keystone2 devices and is based on omapimage format. It re-uses gph header to store the size and loadaddr as done in omapimage.c Signed-off-by: Vitaly Andrianov Signed-off-by: Murali Karicheri Acked-by: Tom Rini

tools, fit_check_sign: verify a signed fit image

2014-03-21T20:40:38Z

add host tool "fit_check_sign" which verifies, if a fit image is signed correct. Signed-off-by: Heiko Schocher Cc: Simon Glass

tools, fit: add fit_info host command

2014-03-21T20:39:37Z

add fit_info command to the host tools. This command prints the name, offset and the len from a property from a node in a fit file. This info can be used to extract a properties data with linux tools, for example "dd". Signed-off-by: Heiko Schocher Acked-by: Simon Glass