u-boot.git/tools/imximage.c, branch v2016.09

imx: tools: imximage: fix CLR bit command

2016-05-17T15:52:19+00:00

Fix incorrect parametr in CMD_CHECK_BITS_CLR command
Pass CLR parameter to DCD header for CMD_CHECK_BITS_CLR

Signed-off-by: Adrian Alonso

imximage: fix commands other than write_data

2015-10-07T11:43:15+00:00

When CHECK_BITS_SET was added, they forgot to add
a new command table, and instead overwrote the
previous table.

Signed-off-by: Troy Kisky 
Tested-by: Fabio Estevam

imximage: header.length of 4 is valid

2015-10-07T11:24:35+00:00

Signed-off-by: Troy Kisky

tools/imximage: set DCD pointer to NULL when its length is 0

2015-09-02T13:25:27+00:00

When dcd_len is 0 the Write Data command that the set_dcd_rst_v2() routine
generates is empty. This causes HAB to complain that the command is invalid.

--------- HAB Event 1 -----------------
event data:
	0xdb 0x00 0x0c 0x41 0x33 0x06 0xc0 0x00
	0xcc 0x00 0x04 0x04

To fix this set the DCD pointer in the IVT to NULL in this case. The DCD header
itself is still needed for detect_imximage_version() to determine the image
version.

Signed-off-by: Baruch Siach 
Acked-by: Stefano Babic

imx: imximage: add new CHECK/CLR BIT command

2015-07-26T10:07:14+00:00

* Extend imximage DCD version 2 to support DCD commands
  CMD_WRITE_CLR_BIT 4 [address] [mask bit] means:
    while ((*address & ~mask) != 0);
  CMD_CHECK_BITS_SET 4 [address] [mask bit] means:
    while ((*address & mask) != mask);
  CMD_CHECK_BITS_CLR 4 [address] [mask bit] means:
    *address = *address & ~mask;
* Add set_dcd_param_v2 helper function to set DCD
  command parameters

Signed-off-by: Adrian Alonso 
Signed-off-by: Peng Fan

Merge branch 'master' of git://www.denx.de/git/u-boot-imx

2015-02-10T15:40:43+00:00

imx: imximage: Add QuadSPI boot support

2015-02-10T11:48:49+00:00

Add QuadSPI boot support to imximage tool.

Note: The QuadSPI configuration parameters at offset 0x400 are not
included in this patch. Need other tools to generate the parameters
part.

Signed-off-by: Ye.Li

imagetool: replace image registration function by linker_lists feature

2015-01-29T18:38:41+00:00

The registration was introduced in commit f86ed6a8d52c99bb2d17d3cac1647edca0c4399c

This commit also removes all registration functions, and the member "next"
from image_type_params struct

Signed-off-by: Guilherme Maciel Ferreira

imximage: Fix the bootdata.size calculation

2014-11-03T09:33:01+00:00

In system boot chapter of i.MX6 reference manual, the "Image Vector Table"
figure shows the bootdata.start points to the beginning of the destination
memory. It means the bootdata.size should contain the IVT offset part,
but the calculation in imximage tool does not have.

We found this issue when booting from QuadSPI NOR on i.MX6SX. The u-boot
runs into abnormal (crash or stop) after booting. After checked the destination
memory where the image is loaded to, there are hundreds of bytes at
the image end are not loaded into memory. Since there is a 4096 bytes
round in the calculation, for the booting devices using smaller IVT offset,
such as SD and SPI booting, they are not easy to reproduce.

Signed-off-by: Ye.Li

imximage: Fix imximage IVT bug for EIM-NOR boot

2014-09-09T14:39:02+00:00

The load region size of EIM-NOR are defined to 0. For this case,
the parameter "imximage_init_loadsize" must be calculated.
The imximage tool implements the calculation in the "imximage_generate"
function, but the following function "imximage_set_header" resets the value
and not calculate. This bug cause some fields of IVT head are not
correct, for example the boot_data and DCD overlay the application area.

Signed-off-by: Ye.Li