| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
|
|
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
|
|
Use CONFIG_NUM_CPUS to match existing define used by 86xx.
Signed-off-by: Kumar Gala <[email protected]>
Acked-by: Jon Loeliger <[email protected]>
|
|
The autostart revert caused a bit of duplicated code as well as
code that was using images->autostart that needs to get removed so
we can build again.
Signed-off-by: Kumar Gala <[email protected]>
|
|
When building the 8544DS board we get this error:
In file included from r8a66597-hcd.c:22:
u-boot/include/usb.h:190:2: error: #error USB Lowlevel not defined
make[1]: *** [r8a66597-hcd.o] Error 1
The cleanest fix is to only build r8a66597-hcd.c if CONFIG_USB_R8A66597_HCD
is set.
Signed-off-by: Kumar Gala <[email protected]>
|
|
This is needed because we will be possibly be locating
devices at physical addresses above 32bits, and the asm
preprocessing does not appear to deal with ULL constants
properly. We now call write_bat in lib_ppc/bat_rw.c.
Signed-off-by: Becky Bruce <[email protected]>
Acked-by: Jon Loeliger <[email protected]>
|
|
Perform sync/isync as required by the architecture.
Signed-off-by: Becky Bruce <[email protected]>
Acked-by: Jon Loeliger <[email protected]>
|
|
Signed-off-by: Becky Bruce <[email protected]>
Acked-by: Jon Loeliger <[email protected]>
|
|
Correct the mx31_gpio_mux() function to allow changing all i.MX31 IOMUX
contacts instead of only the first 256 ones as is the case prior to
this patch.
Add missing MUX_* macros and update board files to use the new macros.
Signed-off-by: Magnus Lilja <[email protected]>
|
|
Correct the names of some IOMUX macros.
Signed-off-by: Magnus Lilja <[email protected]>
|
|
The block and page parameters of onenand_verify_page() are not used. This causes a compiler error when CONFIG_MTD_ONENAND_VERIFY_WRITE is enabled.
Signed-off-by: Steve Sakoman <[email protected]>
Signed-off-by: Dirk Behme <[email protected]>
|
|
|
|
FILL_15BIT_555RGB macro extension for pixel swapping
by commit bed53753dd1d7e6bcbea4339be0fb7760214cc35
introduced a bug in cfb_console:
Bitmaps with odd-numbered width won't be rendered
correctly and even U-Boot crashes are observed on
some platforms while repeated rendering of such
bitmaps with "bmp display". Also if a bitmap is
rendered to an odd-numbered x starting position,
the same problem occurs. This patch is an attempt
to fix it.
Signed-off-by: Anatolij Gustschin <[email protected]>
|
|
If logo_plot() should ever be called with x starting
position other than zero and for pixel depths greater
than 8bpp, logo colors distortion will be observed.
This patch fixes the issue.
Signed-off-by: Anatolij Gustschin <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
Signed-off-by: Roy Zang <[email protected]>
|
|
- os_data_header Variable is a carry over feature
& unused. So removed all instance of this variable
- Minor Code Style Update
Signed-off-by: Gururaja Hebbar <[email protected]>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
|
|
Signed-off-by: Magnus Lilja <[email protected]>
|
|
While locally preparing some U-Boot patches for ARM based OMAP3 boards, some
using OneNAND and some using NAND, we found some differences in OneNAND and
NAND command address handling.
As this might confuse users (it already confused us), we like to align OneNAND
and NAND address handling.
The issue is that cmd_onenand.c subtracts the onenand base address from the
addresses you type into the u-boot command line so, unlike nand, you can't
use addresses relative to the start of the onenand part e.g. this won't work:
onenand read 82000000 280000 400000
you have to use:
onenand read 82000000 20280000 400000
Looking at recent git, the only board currently using OneNAND is Apollon, and
for this the OneNAND base address is 0 (apollon.h)
#define CFG_ONENAND_BASE 0x00000000
so patch below won't break any existing boards and will align OneNAND and NAND
handling on boards where OneNAND base address is != 0.
Signed-off-by: Steve Sakoman <[email protected]>
Signed-off-by: Manikandan Pillai <[email protected]>
Signed-off-by: Dirk Behme <[email protected]>
|
|
The recent change to move the .bss outside of the image gives older
binutils (ld from eldk4.1/binutils-2.16) some headache:
ppc_85xx-ld: u-boot: Not enough room for program headers (allocated 3, need 4)
ppc_85xx-ld: final link failed: Bad value
We workaround it by being explicit about the program headers and not
assigning the .bss to a program header.
Signed-off-by: Kumar Gala <[email protected]>
|
|
This reverts commit f5614e7926863bf0225ec860d9b319741a9c4004.
The commit was based on a misunderstanding of the (documented)
meaning of the 'autostart' environment variable. It might cause
boards to hang if 'autostart' was used, with the potential to brick
them. Go back to the documented behaviour.
Conflicts:
common/cmd_bootm.c
common/image.c
include/image.h
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
|
|
|
|
|
|
|
|
|
|
- enable CFI driver where this was forgotten
- enable mtdparts support
- adjust default environment
etc.
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
boot_get_ramdisk() should not treat the case when a FIT image does
not contain a ramdisk as an error.
Signed-off-by: Peter Tyser <[email protected]>
Acked-by: Michal Simek <[email protected]>
|
|
Fix for page size of AT45DB021. Also adding bigger AT45DB081
which comes with some newer boards.
Signed-off-by: Sergey Lapin <[email protected]>
|
|
Add sh_eth support to sh7763rdp.
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
When switching the TQM8xxL modules to use the CFI flash driver,
support for the second flash bank was broken because the CFI driver
did not support dynamically sized banks. This gets fixed now.
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
The CFI driver allowed only for static initializers in the
CFG_FLASH_BANKS_LIST definition, i. e. it did not allow to map
several flash banks contiguously if the bank sizes were not known in
advance, which kind of violates U-Boot's design philosophy.
(will be used for example by the TQM8xxL boards)
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
Moved static functions earlier in file so forward declarations are not needed.
Signed-off-by: Ben Warren <[email protected]>
|
|
Add MII commands to the UEC driver. Note that once a UEC device is selected,
any device on its MDIO bus can be addressed.
Signed-off-by: David Saada <[email protected]>
Signed-off-by: Ben Warren <[email protected]>
|
|
add support for Renesas R8A66597 usb controller.
This patch supports USB Host mode.
Signed-off-by: Yoshihiro Shimoda <[email protected]>
Signed-off-by: Markus Klotzbuecher <[email protected]>
|
|
Add support to drivers/usb/usbdcore_omap1510.c for OMAP5912 and OMAP16xx devices.
Signed-off-by: Jon Hunter <[email protected]>
Signed-off-by: Markus Klotzbuecher <[email protected]>
|
|
schematic.
The Sequoia board has two UARTs in "4-pin" mode. This patch modifies the GPIO
configuration to match the schematic, and also sets the SDR0_PFC1 register to
select the corresponding mode for the UARTs.
Signed-off-by: Steven A. Falco <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
And in the process eliminate some duplicate register defines.
Signed-off-by: Kenneth Johansson <[email protected]>
|
|
On ADS5121 when booting linux the following errors are seen:
Unable to update property /soc5121@80000000:bus-frequency, err=FDT_ERR_NOTFOUND
Unable to update property /soc5121@80000000/ethernet@2800:local-mac-address, err=FDT_ERR_NOTFOUND
Unable to update property /soc5121@80000000/ethernet@2800:address, err=FDT_ERR_NOTFOUND
This is caused by ft_cpu_setup trying to deal with
both old and new soc node naming. This patch
fixes this by being smarter about what to
fixup.
Also do soc node fixups by compatible instead of by path.
A new board config called OF_SOC_COMPAT defined
to be "fsl,mpc5121-immr" replaces the old
OF_SOC node path that was defined to be "soc@80000000".
Old device trees still work, but the compatiblity
is conditional on CONFIG_OF_SUPPORT_OLD_DEVICE_TREES
which is on by default in include/configs/ads5121.h.
Signed-off-by: John Rigby <[email protected]>
|
|
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
|
