| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Tom Rini <[email protected]>
|
|
This restores support for IOT2050 by widely synchronizing its DT files
with the Linux kernel. We additionally need to add the alias restoration
that is still waiting for its upstream merge and the not-yet-upstreamed
bits needed for watchdog reboot detection.
Fixes: 4dbdc84754ea ("arm: dts: k3-am654: pull in dtb update from Linux")
Signed-off-by: Jan Kiszka <[email protected]>
|
|
Kernel commit 1b77265626a4 ("arm64: dts: ti: k3-j7200-mcu-wakeup: Add
HyperBus node") was merged to kernel without its dependent patch [1].
Similar fix is needed in U-Boot, and hbmc currently breaks boot. Till
this gets fixed in U-Boot, disable the config by default so that the
hbmc probe that happens in board/ti/j721e/evm.c will not take place
and lead to boot failure.
This is similar to the approach in commit 5b2671594b80 ("configs:
j721e: Remove HBMC_AM654 config"), introduced to j7200 evm platform.
[1] https://lore.kernel.org/all/[email protected]/
Signed-off-by: Nishanth Menon <[email protected]>
Reviewed-by: Neha Malcom Francis <[email protected]>
|
|
A "F: foo*" entry does not match any foo*/ folder nor its subtree,
another "F: foo*/" entry is needed for that.
Add missing foo*/ entries where an existing folder was ignored,
so this folder and its subtree is properly covered.
Arm tegra, Arm TI and Environment sections are affected.
Cc: Tom Rini <[email protected]>
Cc: Thierry Reding <[email protected]>
Cc: Svyatoslav Ryhel <[email protected]>
Cc: Tom Rini <[email protected]>
Cc: Joe Hershberger <[email protected]>
Signed-off-by: Anthony Loiseau <[email protected]>
|
|
Commit 19a91f2464a8 ("Create a new boot/ directory") moved the
android_ab.c code under boot/android_ab but did not update
the MAINTAINERS entry.
Update it so that the maintainer will get cc'ed again.
Fixes: 19a91f2464a8 ("Create a new boot/ directory")
Signed-off-by: Mattijs Korpershoek <[email protected]>
Reviewed-by: Sam Protsenko <[email protected]>
|
|
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Sync with kernel v6.7-rc1 and sync up the u-boot dts files accordingly.
Signed-off-by: Nishanth Menon <[email protected]>
|
|
main_timer0 is used by u-boot as the tick-timer. Add it to the soc
devices list so it an be enabled via the k3 power controller.
Signed-off-by: Nishanth Menon <[email protected]>
Reviewed-by: Neha Malcom Francis <[email protected]>
|
|
Bryan Brattlof <[email protected]> says:
Hello Again Everyone!
This series gets the am65x booting again along with syncing the device
tree files with v6.7-rc1 Linux.
The bulk of these patches unify the WKUP SPL board file with the arm64
files to make future syncs from Linux much easier. In the end the DTBs
should look a lot like what the DTBs look like for the am64x which
is fairly similar to the am65x.
For those interested in what UART boot looks like:
https://paste.sr.ht/~bryanb/7df8a645dc548912cd806abd5ecab967ef3287bc
|
|
Many nodes are reused between WKUP SPL, MAIN SPL, and U-Boot. Using
bootph-pre-ram is causing these nodes to be present in SPL builds but
pruned away during the U-Boot build. Convert these nodes to bootph-all
so they will remain no matter which dtb build is happening.
Tested-by: Tom Rini <[email protected]>
Signed-off-by: Bryan Brattlof <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
|
|
With the Linux and U-Boot board dtb files unified, we now have a
duplicate mcu secure proxy node. Remove it
Tested-by: Tom Rini <[email protected]>
Signed-off-by: Bryan Brattlof <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
|
|
The dummy_clock node is used to help the drivers probe the IO needed to
setup consoles and boot media to load firmware into the SoC.
This dummy_clock isn't a device that exists nor does it exist in the
mcu domain. So move it from cbass_mcu to the root node to avoid any
confusion.
Tested-by: Tom Rini <[email protected]>
Signed-off-by: Bryan Brattlof <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
|
|
These aliases are not needed in U-Boot. Remove them
Tested-by: Tom Rini <[email protected]>
Signed-off-by: Bryan Brattlof <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
|
|
With the Linux and U-Boot board dtb files unified, we have duplicate
properties in the root node. Remove them
Tested-by: Tom Rini <[email protected]>
Signed-off-by: Bryan Brattlof <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
|
|
With the Linux and U-Boot board dtb files unified, we now have a
duplicate vtt_pinmux node. Remove it
Tested-by: Tom Rini <[email protected]>
Signed-off-by: Bryan Brattlof <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
|
|
With the Linux and U-Boot board dtb files unified, we now have a
duplicate mdio node. Remove it
Tested-by: Tom Rini <[email protected]>
Signed-off-by: Bryan Brattlof <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
|
|
The pinmux for usb0 is missing from the Linux board dtb file. Remove it
until we can introduce it in Linux
Tested-by: Tom Rini <[email protected]>
Signed-off-by: Bryan Brattlof <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
|
|
With the Linux and U-Boot board dtb files unified, we now have a
duplicate ospi0 node. Remove it
Tested-by: Tom Rini <[email protected]>
Signed-off-by: Bryan Brattlof <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
|
|
With the Linux and U-Boot board dtb files unified, we now have a
duplicate wkup_i2c0 node. Remove it
Tested-by: Tom Rini <[email protected]>
Signed-off-by: Bryan Brattlof <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
|
|
With the Linux and U-Boot board dtb files unified, we now have a
duplicate sdhci1 pinmux node. Remove it
Tested-by: Tom Rini <[email protected]>
Signed-off-by: Bryan Brattlof <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
|
|
With the Linux and U-Boot board dtb files unified, we now have
a duplicate sdhci0 pinmux node. Remove it
Tested-by: Tom Rini <[email protected]>
Signed-off-by: Bryan Brattlof <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
|
|
With the Linux and U-Boot board dtb files unified, we now have a
duplicate main_uart0 node. Remove it
Tested-by: Tom Rini <[email protected]>
Signed-off-by: Bryan Brattlof <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
|
|
With the Linux and U-Boot board dtb files unified we now have a
duplicate mcu_uart0 node. Remove it
Tested-by: Tom Rini <[email protected]>
Signed-off-by: Bryan Brattlof <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
|
|
Ethernet is one of a few IPs in U-Boot that depend on DMA to operate.
However there are a few missing registers ranges in the udmap nodes
need to properly setup DMA for the am65x.
A fix has been added to the Linux kernel[0] to add these ranges however
they have not made it to a Linux tag. To keep DMA operational until the
next DT sync from Linux, add these ranges to the *-u-boot.dtsi with a
note for our future selves.
[0] https://lore.kernel.org/r/[email protected]
Tested-by: Tom Rini <[email protected]>
Signed-off-by: Bryan Brattlof <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
|
|
With the Linux and U-Boot board dtb files unified, we now have a
duplicate mcu_udmap node. Remove it
Tested-by: Tom Rini <[email protected]>
Signed-off-by: Bryan Brattlof <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
|
|
With the Linux and U-Boot board dtb files unified, we now have a
duplicate mcu_ringacc node. Remove it
Tested-by: Tom Rini <[email protected]>
Signed-off-by: Bryan Brattlof <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
|
|
timer1 is really just the mcu_timer0 node redefined for the WKUP SPL.
Remove the timer1 and replace it with the mcu_timer0 from the Linux
device tree we imported into U-Boot.
Tested-by: Tom Rini <[email protected]>
Signed-off-by: Bryan Brattlof <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
|
|
With the Linux and U-Boot board files unified, we now have a duplicate
wkup_uart0 node. Remove it
Tested-by: Tom Rini <[email protected]>
Signed-off-by: Bryan Brattlof <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
|
|
With the Linux and U-Boot board dtb files unified we now have a
duplicate vtt_supply node. Remove it
Tested-by: Tom Rini <[email protected]>
Signed-off-by: Bryan Brattlof <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
|
|
To make things as organized as possible, start from the Linux board dtbs
and apply all properties needed for U-Boot in our *-u-boot.dtsi file for
the MAIN SPL and U-Boot builds.
We can then include these files for the WKUP SPL build making further
edits to the needed properties and nodes for the WKUP SPL bootloader's
view of the am65x.
Tested-by: Tom Rini <[email protected]>
Signed-off-by: Bryan Brattlof <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
|
|
In order to unify the R5 board dtb file with the Linux board dtb file,
we will need to copy all bootph-pre-ram properties to the *-u-boot.dtsi
overlay.
Tested-by: Tom Rini <[email protected]>
Signed-off-by: Bryan Brattlof <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
|
|
Pull in dtb updates for the am654 base board from v6.7-rc1 of Linux
Tested-by: Tom Rini <[email protected]>
Signed-off-by: Bryan Brattlof <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
|
|
The R5 board file for U-Boot should be the same as the board file copied
from Linux with a few alterations to work with the R5's view of the SoC.
First we need to unify the R5 board file and it's U-Boot overlay before
we can unify the Linux board file with this one.
Tested-by: Tom Rini <[email protected]>
Signed-off-by: Bryan Brattlof <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
|
|
We do not have a need to share a single console with the evaluation
board and disabling this option reduces the complexity of configuring
the consoles. Disable CONSOLE_MUX
Tested-by: Tom Rini <[email protected]>
Signed-off-by: Bryan Brattlof <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
|
|
Some of the regulators we need to successfully boot are fixed
regulators. Enable the driver to properly probe them.
Tested-by: Tom Rini <[email protected]>
Signed-off-by: Bryan Brattlof <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
|
|
Apple machines do not have memory below 4G. Since U-Boot does
not support the SMBIOS 3 header structures this means we can't
support SMBIOS on these machines. Unfortunately the refactoring
of the SMBIOS code this cycle accidentally enabled it again.
Fixes: 53fab13a7b1 ("efi: Use the installed SMBIOS tables")
Signed-off-by: Mark Kettenis <[email protected]>
Reviewed-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Fix the wrong clock divider calculation.
Signed-off-by: Jim Liu <[email protected]>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
- Make DRAM stable on i.MX8MP DHCOM SoM by using FPWM mode and updating
the DRAM timing
- Fix display artifacts when booting Linux on i.MX8M Mini/Plus eDM SBC
|
|
Add the --git parameter, else recent contributors are left out of the CC list.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Fixes: d0253f7e5ca1 ("doc: move README.NetConsole to HTML documentation")
Signed-off-by: Baruch Siach <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
|
|
Currently the wget command is hard wired to HTTP port 80. This is
inconvenient, as it is extremely easy to start trivial HTTP server
as an unprivileged user using e.g. python http module to serve the
files, but such a server has to run on one of the higher ports:
"
$ python3 -m http.server -d $(pwd) 8080
"
Make it possible to configure HTTP server port the same way it is
possible to configure TFTP server port, using environment variable
'httpdstp' (similar to 'tftpdstp'). Retain port 80 as the default
fallback port. This way, users can start their own trivial server
and conveniently download whatever files they need into U-Boot.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
|
|
The current DDR subsystem configuration occasionally results in write failures,
impacting memory stability, on Verdin AM62 Solo 512MB WB IT 0072 SKU.
This commit addresses the issue by adjusting Drive Pull-Up/Down and
Write Latency to improve the eye diagram and ensure reliable write operations.
This configuration is shared with all Verdin AM62 SoM and
it does not introduce regressions.
Configurations changes from previous / default values:
- Drive Pull-Up/Down from 40 to 34.3 Ohm
- Write Latency from 8 to 10
- ODTLon / ODTLoff latency from 0 / 0 to 4 / 20 nCK
- VREF control range 1 at 27 %
- tFAW from 30 to 40 ns
Configuration is output from SysConfig [1] web tool, currently at version
1.18.1+3343 (DDR SubSystem v9.10).
[1] https://dev.ti.com/sysconfig
Fixes: 7d1a10659f5b ("board: toradex: add verdin am62 support")
Signed-off-by: Emanuele Ghidoli <[email protected]>
Signed-off-by: Francesco Dolcini <[email protected]>
Acked-by: Marcel Ziswiler <[email protected]>
|
|
The contents of README.sha1 only refer to process around verification
of the pcs440ep board firmware in flash. The device was removed in
commit 242836a893ae ("powerpc: ppc4xx: remove pcs440ep support") in
2015 so this readme isn't really relevant anymore so can be removed.
Signed-off-by: Peter Robinson <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Turn display connector power off on boot and reboot to prevent any
bogus start up sequence of any panel potentially attached to the
display connector.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Signed-off-by: Tom Rini <[email protected]>
|
|
Import DRAM timings generated by the DDR tool 3.31 which introduce assorted
tweaks to the DRAM controller settings. Furthermore, enable DBI to improve
noise resilience of the DRAM bus by reducing the number of bit changes on
the bus.
Reduce the DRAM rate to 3600 MTps to remove all remaining correctable errors
reported by EDAC . It is not entirely clear why the slightly faster setting
does produce sporadic correctable errors, while this one does not, but this
could be related to simpler PLL setting at 3600 MTps.
Enable inline ECC which is necessary to detect ECC errors and collect
statistics by the EDAC driver in Linux. This reduces the DRAM size by
64 MiB for each 512 MiB of DRAM, so for a 4 GiB device the available
DRAM size becomes 3.5 GiB and for 2 GiB device the available DRAM size
becomes 1.8 GiB.
Signed-off-by: Marek Vasut <[email protected]>
|
|
In case the Buck5 and Buck6 regulators which supply DRAM Vdd1 and Vdd2/Vddq
respectively operate in automatic PWM/PFM mode, the DRAM EDAC detects more
correctable errors than if the regulators operate in forced PWM only mode.
Force DRAM regulators to forced PWM mode only to stop tempting the DRAM.
Signed-off-by: Marek Vasut <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-clk
clock changes for u-boot/master
This has some clock fixes which should go in before the release. It's a bit
late in the cycle, but most of these have tests to go along with them.
Signed-off-by: Sean Anderson <[email protected]>
|
|
Fix unused variable error produced by building tests
Fixes: d3061824 (test: dm: clk_ccf: test ccf_clk_ops)
Signed-off-by: Yang Xiwen <[email protected]>
Reviewed-by: Sean Anderson <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
