| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Markus Heidelberg <[email protected]>
|
|
Attempt to bring i386 / sc520 inline with master
Signed-off-by: Graeme Russ <[email protected]>
|
|
Add support for environment in NAND with automatic NOR / NAND recognition,
including unaligned environment, bad-block skipping, redundant environment
copy.
Signed-off-by: Guennadi Liakhovetski <[email protected]>
|
|
Signed-off-by: Matthias Fuchs <[email protected]>
Acked-by: Stefan Roese <[email protected]>
|
|
Signed-off-by: Sergei Poselenov <[email protected]>
|
|
This patch adds Lime GDC support together with support for the PWM
backlight control through the w83782d chip. The reset pin of the
latter is attached to GPIO, so we need to reset it in
early_board_init_r.
Signed-off-by: Anatolij Gustschin <[email protected]>
|
|
- Update the local bus ranges in the FDT for Linux for the various
devices connected to the local bus via chip-select.
- Set the LCRR_DBYP bit in the LCRR for local bus frequencies
lower than 66 MHz and uses I/O accessor functions consequently.
- UPM data update.
- Update of default environment and configuration. Use I2C multibus
as we do have two I2C buses. Also enable sdram and ext2 commands.
Signed-off-by: Wolfgang Grandegger <[email protected]>
Signed-off-by: Sergei Poselenov <[email protected]>
Signed-off-by: Detlev Zundel <[email protected]>
|
|
The new sys_eeprom.c supports both the old CCID EEPROM format and the new NXID
format, and so it obsoletes board/freescale/common/cds_eeprom.c. Freescale
86xx boards already use sys_eeprom.c, so this patch migrates the remaining
Freescale 85xx boards to use it as well. cds_eeprom.c is deleted.
Signed-off-by: Timur Tabi <[email protected]>
|
|
This allows to use show_activity() without having to
define an empty board_show_activity() function.
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
Conflicts:
Makefile
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
|
|
This patch fixes warnings like this:
start.S:0: warning: target CPU does not support interworking
which come from some ARM cross compilers and are caused by hard-coded
(with "--with-cpu=arm9" configuration option) ARM targets (which
support ARM Thumb instructions), while the ARM target selected from
the command line (with "-march=armv4") doesn't support Thumb
instructions.
This warning is issued by the compiler regardless of the real use of
the Thumb instructions in code.
To fix this problem, we use options according to compiler version
being used.
Signed-off-by: Sergei Poselenov <[email protected]>
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
Signed-off-by: Sergei Poselenov <[email protected]>
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
bootm.c:128: warning: label 'error' defined but not used
bootm.c:65: warning: unused variable 'ret'
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
missing doc_probe() prototype.
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
This patch moves some 4xx specific prototypes out of include common.h
to a ppc4xx specific header.
Signed-off-by: Stefan Roese <[email protected]>
|
|
|
|
This patch add FDT support and command line editing capabilities
for CPCI405 and CPCI405AB boards.
Signed-off-by: Matthias Fuchs <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Signed-off-by: Matthias Fuchs <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
This patch replaces the BOARD_REVISION variable in include/config.mk
by a using a temporary include file in the platform directory.
The former way does not work anymore and the latter is also used by
some other boards.
Signed-off-by: Matthias Fuchs <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Since this define is only used on one board that was never really in
production, removing this compile time option doesn't hurt and makes
the code more readable.
Signed-off-by: Stefan Roese <[email protected]>
|
|
This patch fixes a compilation warning for the PIP405 board. It moves the
#ifndef CONFIG_CS8952_PHY define a little so that the warning doesn't
occur anymore. I am a little unsure if this #ifdef is at the correct
place now or if it could be removed completely. This needs to get
tested on the PIP405 board.
Signed-off-by: Stefan Roese <[email protected]>
|
|
Signed-off-by: Stefan Roese <[email protected]>
|
|
ctrl_regs.c: In function 'compute_fsl_memctl_config_regs':
ctrl_regs.c:523: warning: 'caslat' may be used uninitialized in this function
ctrl_regs.c:523: note: 'caslat' was declared here
Add a warning in DDR1 case if cas_latency isn't a value we know about.
Signed-off-by: Kumar Gala <[email protected]>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
|
|
Signed-off-by: Shinya Kuribayashi <[email protected]>
|
|
Adds returning an error from the ramdisk detection code if
its not a real ramdisk (invalid). There is no reason we can't
just return back to the console if we detect an invalid
ramdisk or CRC error.
Signed-off-by: Kumar Gala <[email protected]>
|
|
This patch adds bootm_start() return value check. If
error status is returned, we do not proceed further to
prevent board reset or crash as we still can recover
at this point.
Signed-off-by: Anatolij Gustschin <[email protected]>
|
|
rearrange some #if !defined() / #else / #endif statements to remove
the negative logic.
Signed-off-by: Andrew Dyer <[email protected]>
|
|
Signed-off-by: Kyungmin Park <[email protected]>
|
|
I didn't try to use drivers/mtd/nand/fsl_upm.c for the NAND driver,
because I have no longer access to the hardware.
Signed-off-by: Heiko Schocher <[email protected]>
|
|
Fix compile problems caused by
commit cfa460adfdefcc30d104e1a9ee44994ee349bb7b
Signed-off-by: Heiko Schocher <[email protected]>
|
|
Signed-off-by: Kyungmin Park <[email protected]>
|
|
Added new CONFIG_DISABLE_CONSOLE define and GD_FLG_DISABLE_CONSOLE.
When CONFIG_DISABLE_CONSOLE is defined, setting
GD_FLG_DISABLE_CONSOLE disables all console input and output.
Signed-off-by: Mark Jackson <[email protected]>
|
|
Signed-off-by: Ricardo Ribalda Delgado <[email protected]>
|
|
Some of multi-function USB controllers (e.g. ISP1562) allow root hub
resetting only via EHCI registers. So, this patch adds the
corresponding kind of reset to OHCI's hc_reset() if the newly
introduced CONFIG_PCI_EHCI_DEVNO option is set (e.g. for Socrates
board).
Signed-off-by: Yuri Tikhonov <[email protected]>
Acked-by: Markus Klotzbuecher <[email protected]>
|
|
Signed-off-by: Yuri Tikhonov <[email protected]>
|
|
|
|
This patch fixes a problem spotted on Glacier/Canyonlands (and most
likely lots of other board ports), that no serial output was seen
after console initialization in console_init_r(). This is because the
last added console device was used instead of the first added.
This patch fixes this problem by using list_add_tail() instead of
list_add() to register a device. This way the first added console
is used again.
Signed-off-by: Stefan Roese <[email protected]>
|
|
This patch adds GPCS, SGMII and M88E1112 PHY support
for the AMCC PPC460GT/EX processors.
Signed-off-by: Victor Gallardo <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Signed-off-by: Adam Graham <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Alternate SDRAM DDR autocalibration routine that can be generically used
for any PPC4xx chips that have the IBM SDRAM Controller core allowing for
support of more DIMM/memory chip vendors and gets the DDR autocalibration
values which give the best read latency performance (SDRAM0_RDCC.[RDSS]).
Two alternate SDRAM DDR autocalibration algoritm are provided in this patch,
"Method_A" and "Method_B". DDR autocalibration Method_A scans the full range
of possible PPC4xx SDRAM Controller DDR autocalibration values and takes a
lot longer to run than Method_B. Method_B executes in the same amount of time
as the currently existing DDR autocalibration routine, i.e. 1 second or so.
Normally Method_B is used and it is set as the default method.
The current U-Boot PPC4xx DDR autocalibration code calibrates the IBM SDRAM
Controller registers.[bit-field]:
1) SDRAM0_RQDC.[RQFD]
2) SDRAM0_RFDC.[RFFD]
This alternate PPC4xx DDR autocalibration code calibrates the following
IBM SDRAM Controller registers.[bit-field]:
1) SDRAM0_WRDTR.[WDTR]
2) SDRAM0_CLKTR.[CKTR]
3) SDRAM0_RQDC.[RQFD]
4) SDRAM0_RFDC.[RFFD]
and will also use the calibrated settings of the above four registers that
produce the best "Read Sample Cycle Select" value in the SDRAM0_RDCC.[RDSS]
register.[bit-field].
Signed-off-by: Adam Graham <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
