summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2012-10-03lacie_kw: add support for EFI partitionsSimon Guinot
Defines CONFIG_EFI_PARTITION for LaCie boards. Additionally this patch defines CONFIG_DOS_PARTITION. Note that this definition is implicit in mv_common.h when CONFIG_CMD_USB is enabled. Signed-off-by: Simon Guinot <[email protected]>
2012-10-03rmobile: Fix build timer driver with BUILD_DIRNobuhiro Iwamatsu
Rmobile common timer driver diverts the same driver as SH architecture. When it builds at the same place with source, it is no problem, but when it builds out of source, it cannot build. This patch revises this problem. Reported-by: Albert ARIBAUD <[email protected]> Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
2012-10-03i2c: sh: Remove irq_wait functionNobuhiro Iwamatsu
irq_wait function is not referred to from anywhere. Reported-by: Albert ARIBAUD <[email protected]> Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
2012-10-03doc/git-mailrc: Add 'rmobile' aliasNobuhiro Iwamatsu
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
2012-10-03rmobile: Add READMENobuhiro Iwamatsu
This add README of Renesas RMOBILE. Based doc/README.omap3. Signed-off-by: Nobuhiro Iwamatsu <[email protected]> Acked-by: Tom Rini <[email protected]>
2012-10-03rmobile: armadillo-800eva: Remove CONFIG_SYS_NO_L2CACHENobuhiro Iwamatsu
armadillo-800eva needs this config. Signed-off-by: Nobuhiro Iwamatsu <[email protected]> Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
2012-10-03rmobile: armadillo-800eva: Add Support NFS and BOOTZ commandNobuhiro Iwamatsu
Signed-off-by: Nobuhiro Iwamatsu <[email protected]> Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
2012-10-03rmobile: armadillo-800eva: Add Support CONFIG_OF_LIBFDTNobuhiro Iwamatsu
Signed-off-by: Nobuhiro Iwamatsu <[email protected]> Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
2012-10-03rmobile: armadillo-800eva: Change init function of SCIFA1Nobuhiro Iwamatsu
This initializes GPIO, without using PFC framework in board_early_init_f function. It is because it cannot initialize normally when PFC is used. Signed-off-by: Nobuhiro Iwamatsu <[email protected]> Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
2012-10-03arm: rmobile: Add cpu_eth_init functionNobuhiro Iwamatsu
This supports ethernet driver of RMOBILE R8A7740. Signed-off-by: Nobuhiro Iwamatsu <[email protected]> Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
2012-10-03arm: rmobile: armadillo-800eva Remove board_eth_initNobuhiro Iwamatsu
Signed-off-by: Nobuhiro Iwamatsu <[email protected]> Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
2012-10-03arm: rmobile: Add support for ATMARK-TECHNO Armadillo-800EVA boardHideyuki Sano
The Armadillo-800EVA board has Renesas R-Mobile R8A7740, 512MB DDR3-SDRAM, Ethernet, and more. This patch supports the following functions: - 512MB DDR3-SDRAM - Serial console (SCIF) - Ethernet MAC(MII) & PHY(SMSC) Signed-off-by: Hideyuki Sano <[email protected]> Signed-off-by: Nobuhiro Iwamatsu <[email protected]> Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
2012-10-03arm: rmobile: Add support PFC of Renesas R8A7740Nobuhiro Iwamatsu
Renesas R8A7740 has GPIO based PFC. This privode framework of PFC. The code included in this base from linux kernel. Signed-off-by: Hideyuki Sano <[email protected]> Signed-off-by: Nobuhiro Iwamatsu <[email protected]> Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
2012-10-03arm: rmobile: Add support Renesas R8A7740Nobuhiro Iwamatsu
Renesas R8A7740 is CPU with Cortex-A9. This supports the basic register definition and GPIO. Signed-off-by: Hideyuki Sano <[email protected]> Signed-off-by: Nobuhiro Iwamatsu <[email protected]> Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
2012-10-03arm: rmobile: kzm9g: Add CONFIG_GLOBAL_TIMER to board config fileNobuhiro Iwamatsu
kzm9g board use global timer. But by commit 813ffda31, timer function of rmobile was changed that global timer might be used, when CONFIG_GLOBAL_TIMER was defined. This add CONFIG_GLOBAL_TIMER to board config file. Signed-off-by: Nobuhiro Iwamatsu <[email protected]> Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
2012-10-03arm: rmobile: Add support TMU base timer functionNobuhiro Iwamatsu
Some rmobile SoC has TMU base timer function. This supports TMU. Signed-off-by: Nobuhiro Iwamatsu <[email protected]> Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
2012-10-03arm: rmobile: Change initializing ICCICR registerNobuhiro Iwamatsu
There is rmobile without ICCICR. ICCICR is initialized only when ICCICR is defined. Signed-off-by: Nobuhiro Iwamatsu <[email protected]> Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
2012-10-03arm: rmobile: kzm9g: remove unrelated configNobuhiro Iwamatsu
Remove CONFIG_ARM_CORTEXA9. Signed-off-by: Nobuhiro Iwamatsu <[email protected]> Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
2012-10-03arm: rmobile: kzm9g: Add LIBFDT supportNobuhiro Iwamatsu
Signed-off-by: Nobuhiro Iwamatsu <[email protected]> Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
2012-10-03arm: rmobile: kzm9g: separate cpu_rev to integer and fractionTetsuyuki Kobayashi
According to SoC document, revision info is separated to integer part and fracton part. So I separete rmobile_get_cpu_rev() to rmobile_get_cpu_rev_integer() and rmobile_get_cpu_rev_fraction(). Signed-off-by: Tetsuyuki Kobayashi <[email protected]> Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
2012-10-03arm: rmobile: kzm9g: fix CPU infoTetsuyuki Kobayashi
CPU info register was read wrongly by mistake. And function rmobile_get_cpu_rev() was not called properly. Signed-off-by: Tetsuyuki Kobayashi <[email protected]> Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
2012-10-03arm: rmobile: kzm9g: remove unrelated configTetsuyuki Kobayashi
Remove CONFIG_INTEGRATOR and CONFIG_ARCH_CINTEGRATOR. These are not for kzm9g. Signed-off-by: Tetsuyuki Kobayashi <[email protected]> Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
2012-10-03arm: rmobile: kzm9g: add NFS_TIMEOUT in config fileTetsuyuki Kobayashi
Set NFS_TIMEOUT to 10,000 msec. Signed-off-by: Tetsuyuki Kobayashi <[email protected]> Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
2012-10-03arm: rmobile: kzm9g: Fix CONFIG_BAUDRATE settingTetsuyuki Kobayashi
The value of CONFIG_BAUDRATE is treated as string and put as initial value of environment variable. If it begin with '(', it is wrongly parsed to 0 in number. So I removed '(' and ')'. Signed-off-by: Tetsuyuki Kobayashi <[email protected]> Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
2012-10-03arm: rmobile: kzm9g: Add dummy member to struct sh73a0_rwdtTetsuyuki Kobayashi
Add dummy member to struct sh73a0_rwdt in sh73a0.h. Without this, initializing watch dog timer goes wrong. Signed-off-by: Tetsuyuki Kobayashi <[email protected]> Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
2012-10-03arm: rmobile: Support build with gcc-4.6 or laterNobuhiro Iwamatsu
Latest rmobile code was tested by using old gcc (gcc-4.4). When we use gcc-4.6 (or later), the build is made, but does not work. This solves a problem not to work by add -march=armv5 to compiple option when we built in gcc-4.6 (or later). I tested by linaro's compiler version 2012.04-20120426. Signed-off-by: Nobuhiro Iwamatsu <[email protected]> Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
2012-10-03arm: rmobile: kzm9g: enable reset commandTetsuyuki Kobayashi
Do soft power on reset in U-Boot reset command. Signed-off-by: Tetsuyuki Kobayashi <[email protected]> Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
2012-10-03arm: rmobile: kzm9g: Modify bus controller setting for CS4Tetsuyuki Kobayashi
Problem: Linux kernel hangs up when it write a file to NFS mounted directory. Solution: Modify bus controller setting for CS4, which connected smsc9221 ethernet controller. Detail: Modify CS4BCR bit[29:28] (IWW[1:0]) from 00 to 01. Modify CS4BCR bit[20:19] (IWRRD[1:0]) from 00 to 01. Modify CS4BCR bit[17:16] (IWRRS[1:0]) from 00 to 01. Modify CS4WCR bit[27:26] (WSW[1:0]) from 10 to 11 Modify CS4WCR bit[25:24] (WHW[1:0]) from 01 to 10 Modify CS4WCR bit[18:16] (WW[2:0]) from 101 to 111 Modify CS4WCR bit[13:11] (SW[2:0]) from 010 to 011 Modify CS4WCR bit[10:7] (WR[3:0]) from 1000 to 1011 Signed-off-by: Tetsuyuki Kobayashi <[email protected]> Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
2012-10-03arm: rmobile: kzm9g: change prompt to board specificTetsuyuki Kobayashi
Change U-Boot prompt to board specific one. Signed-off-by: Tetsuyuki Kobayashi <[email protected]> Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
2012-10-03arm: rmobile: kzm9g: Adjust low level hardware settingTetsuyuki Kobayashi
Adjust low level hardware setting in s_init. Signed-off-by: Tetsuyuki Kobayashi <[email protected]> Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
2012-10-03arm: rmobile: kzm9g: Modify sdram areaTetsuyuki Kobayashi
Reserve first 16MB for RT-CPU (as same as kernel config). Signed-off-by: Tetsuyuki Kobayashi <[email protected]> Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
2012-10-03arm: rmobile: Add supoprt for KMC KZM-A9-GT boardNobuhiro Iwamatsu
The KZM-A9-GT board has Renesas R-Mobile SH73A0, 512MB DDR2-SDRAM, USB, Ethernet, and more. This patch supports the following functions: - 512MB DDR2-SDRAM - 16MB NOR Flash memory - Serial console (SCIF) - Ethernet (SMSC) - I2C Signed-off-by: Nobuhiro Iwamatsu <[email protected]> Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
2012-10-03arm: rmobile: Add support PFC of Renesas SH73A0Nobuhiro Iwamatsu
Renesas SH73A0 has GPIO based PFC. This privode framework of PFC. The code included in this base from linux kernel. Signed-off-by: Nobuhiro Iwamatsu <[email protected]> Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
2012-10-03arm: rmobile: Add support Renesas SH73A0Nobuhiro Iwamatsu
Renesas SH73A0 is CPU with Cortex-A9. This supports the basic register definition and GPIO. Signed-off-by: Nobuhiro Iwamatsu <[email protected]> Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
2012-10-03arm: rmobile: Add basic support for Renesas R-MobileNobuhiro Iwamatsu
This patch adds minimum support for R-Mobile. Only minimal support with timer. This CPU can uses the peripheral of Renesas SuperH. Signed-off-by: Nobuhiro Iwamatsu <[email protected]> Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
2012-10-03ARMv7: Add register definition of global timerNobuhiro Iwamatsu
ARMv7 has global timer. This provides the register definition of this timer. Signed-off-by: Nobuhiro Iwamatsu <[email protected]> Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
2012-10-01omap4_panda: remove CONFIG_PANDA, not usedPeter Meerwald
Signed-off-by: Peter Meerwald <[email protected]>
2012-10-01am335x-evm config: decrease bootdelay to 1s and mount rootfs ROKoen Kooi
A fast boot is important to the beaglebone, so save 2 seconds here by decreasing bootdelay. This is still plenty time to break into the prompt, I do that at least once a day. Mount the rootfs RO by default, this is needed to make fsck succeed without resorting to an initramfs. Signed-off-by: Koen Kooi <[email protected]>
2012-10-01am33xx: Fix fetching of mmc1 bootmode from bootrom for AM33XXJoel A Fernandes
U-boot should not ignore getting the bootmode passed on from the bootrom. With this, U-boot SPL knows it was loaded from MMC1 and use this info to read full U-boot from MMC1 as well. Cc: [email protected] Cc: [email protected] Signed-off-by: Joel A Fernandes <[email protected]> Signed-off-by: Tom Rini <[email protected]>
2012-10-01OMAP: networking support for SPLIlya Yanok
This patch adds support for networking in SPL. Some devices are capable of loading SPL via network so it makes sense to load the main U-Boot binary via network too. This patch tries to use existing network code as much as possible. Unfortunately, it depends on environment which in turn depends on other code so SPL size is increased significantly. No effort was done to decouple network code and environment so far. Signed-off-by: Ilya Yanok <[email protected]> Acked-by: Joe Hershberger <[email protected]> Signed-off-by: Tom Rini <[email protected]>
2012-10-01am335x_evm: enable networking in SPLIlya Yanok
This patch adds support for networking in SPL on TI AM335x based boards. Vendor Class Identifier used by SPL during BOOTP is "AM335x U-Boot SPL". Signed-off-by: Ilya Yanok <[email protected]>
2012-10-01OMAP: spl: call timer_init() from SPLIlya Yanok
We need to initialize timer properly, otherwise all delays inside SPL will be wrong. Signed-off-by: Ilya Yanok <[email protected]>
2012-10-01net/bootp: add VCI support for BOOTP alsoIlya Yanok
Vendor Class Identifier option is common to BOOTP and DHCP and can be useful without PXE. So send VCI in both BOOTP and DHCP requests if CONFIG_BOOTP_VCI_STRING is defined. Signed-off-by: Ilya Yanok <[email protected]> Signed-off-by: Tom Rini <[email protected]>
2012-10-01davinci: ea20: add some configs and default environmet variablesBastian Ruppert
Signed-off-by: Bastian Ruppert <[email protected]> CC: Tom Rini <[email protected]> Acked-by: Stefano Babic <[email protected]>
2012-10-01da850/omap-l138: davinci_emac: Suppress auto negotiation if neededBastian Ruppert
negotiation is enabled in RMII mode. Some boards based on da850 need to suppress this procedure. CC: Rajashekhara, Sudhakar <[email protected]> CC: Lad, Prabhakar <[email protected]> CC: Hadli, Manjunath <[email protected]> CC: [email protected] Acked-by: Stefano Babic <[email protected]> CC: Tom Rini <[email protected]> Signed-off-by: Bastian Ruppert <[email protected]> Acked-by: Prabhakar Lad <[email protected]>
2012-10-01video: cfb_console: add function to plot the logo area blackBastian Ruppert
Signed-off-by: Bastian Ruppert <[email protected]> CC: Anatolij Gustschin <[email protected]> CC: Tom Rini <[email protected]> CC: Stefano Babic <[email protected]>
2012-10-01video: cfb_console: logo can be positioned via the splashpos variableBastian Ruppert
Extend the driver for placing the video/bmp logo as specified by "splashpos" environment variable. Signed-off-by: Bastian Ruppert <[email protected]> Signed-off-by: Anatolij Gustschin <[email protected]> CC: Stefano Babic <[email protected]> Signed-off-by: Tom Rini <[email protected]>
2012-10-01davinci: ea20: the console is always set to the serial lineBastian Ruppert
Do not allow to overwrite it when video is enabled. Signed-off-by: Bastian Ruppert <[email protected]> CC: Tom Rini <[email protected]> Acked-by: Stefano Babic <[email protected]>
2012-10-01davinci: ea20: reorganisation LCD startupBastian Ruppert
Signed-off-by: Bastian Ruppert <[email protected]> CC: Tom Rini <[email protected]> Acked-by: Stefano Babic <[email protected]>
2012-10-01devkit8000: add rootwait to mmcboot optionAndreas Bießmann
Signed-off-by: Andreas Bießmann <[email protected]> cc: Thomas Weber <[email protected]>
generated by cgit v1.2.3 (git 2.25.1) at 2026-05-28 17:00:21 +0000