| Age | Commit message (Collapse) | Author |
|---|
|
Enable SPL DTO support to apply matching SoM specific DTOs to cater
for the SoM differences in DH i.MX8MP DHCOM PDK2 configuration. This
is already enabled in DH i.MX8MP DHCOM PDK3 configuration so align
the two configurations.
Fixes: ad1158c50e0e ("arm64: dts: imx8mp: Switch to DT overlays for i.MX8MP DHCOM SoM")
Signed-off-by: Marek Vasut <[email protected]>
|
|
With DM enabled, there is no need for board code to initialize
the Ethernet interfaces.
Specifically board_interface_eth_init will handle the configuration of
GPR1.
Signed-off-by: Tim Harvey <[email protected]>
|
|
The assigned-clock no longer have to be dropped, the clock are now
defined in clk-imx8mp.c and used by DWMAC driver to configure the
DWMAC clock. Drop the workarounds from U-Boot specific DT extras.
Having the clocks dropped causes the EQoS to be non-functional.
See commit c7ea9612df0f ("arm64: dts: imx8mp: Drop EQoS clock
workaround").
Fixes: 48c6f9777cee ("board: gateworks: venice: add imx8mp-gw7905-2x support")
Signed-off-by: Tim Harvey <[email protected]>
|
|
The GW74xx USB1 controller connects to a dual-role connector using a GPIO
for role detection via the usb-connector Linux driver (usb-conn-gpio.c).
This drive does not exist yet in U-Boot so for now we will just default
USB1 to host mode.
Signed-off-by: Tim Harvey <[email protected]>
|
|
Add nvme device 0 to available boot devices.
Signed-off-by: Tim Harvey <[email protected]>
|
|
Due to supply chain issues Venice boards use either a DP83867 or a
GPY111 RGMII PHY. We already print an identifier for the DP83867 so add
one for the GPY111 to better identify what PHY is on a board:
Example:
Net: GPY111 eth0: ethernet@30be0000 [PRIME]
Net: DP83867 eth0: ethernet@30be0000 [PRIME]
Signed-off-by: Tim Harvey <[email protected]>
|
|
Extensive testing has shown that at higher temperatures operating
without a GSC backup battery, the GSC needs a small delay after
releasing the I2C SDA/SCL pins before it is ready to handle I2C
requests.
Add a delay to avoid errors such as:
wait_for_sr_state: Arbitration lost sr=93 cr=80 state=2020
i2c_init_transfer: failed for chip 0x20 retry=0
Signed-off-by: Tim Harvey <[email protected]>
|
|
The Gateworks System Controller (GSC) has a voltage supervisor which is
disabled by default. On older boards we want to maintian this but on
newer boards we wish to enable the voltage supervisor.
The Gateworks System Controller (GSC) can disable the board primary
power supply by driving a pin to a FET high. On older board models
the leakage of the GSC may exceed the leakage of the FET causing this
signal slowly rise when the GSC battery is low and the board is in a
powered down state resulting in the board being kept in a disabled
state.
Newer boards have a hardware fix to avoid this leakage and thus should
enable the voltage supervisor.
Signed-off-by: Tim Harvey <[email protected]>
|
|
Drop redundant header imports with dts/upstream already providing
updated headers which have been checked to be backwards compatibility.
The imx headers which aren't present in dts/upstream are as follows:
- include/dt-bindings/clock/imxrt1020-clock.h
- include/dt-bindings/clock/imx8qm-clock.h
- include/dt-bindings/clock/imxrt1170-clock.h
- include/dt-bindings/clock/imx8qxp-clock.h
- include/dt-bindings/memory/imxrt-sdram.h
- include/dt-bindings/pinctrl/pads-imx8qxp.h
- include/dt-bindings/pinctrl/pads-imx8qm.h
- include/dt-bindings/soc/imx8_pd.h
- include/dt-bindings/soc/imx_rsrc.h
hence these aren't dropped yet but there was an unused header:
- include/dt-bindings/pinctrl/pins-imx8mq.h
which has been dropped as well. There shouldn't be any funtional impact
with this change but it rather allows iMX platforms to use upstream
dt-bindings headers in a backwards compatible manner.
Signed-off-by: Sumit Garg <[email protected]>
Reviewed-by: Michael Trimarchi <[email protected]>
|
|
Migrate imx6ulz_bsh_smm_m2 board to OF_UPSTREAM.
Signed-off-by: Patrick Barsanti <[email protected]>
|
|
Migrate imx8mn_bsh_smm_s2 and imx8mn_bsh_smm_s2pro boards to OF_UPSTREAM.
Signed-off-by: Patrick Barsanti <[email protected]>
Tested-by: Michael Trimarchi <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
|
|
A while back we moved the core functions of the EFI TCG protocol to the
TPM APIs in order for them to be used with bootm, booti etc.
Some prototypes changed from returning efi_status_t to int, which is more
appropriate for the non-EFI APIs. However, some of the EFI callsites never
changed and we ended up assigning the int value to efi_status_t.
This is unlikely to cause any problems, apart from returning invalid
values on failures and violating the EFI spec. Let's fix them
by looking at the new return code and map it to the proper EFI return
code on failures.
Fixes: commit 97707f12fdab ("tpm: Support boot measurements")
Fixes: commit d6b55a420cfc ("efi_loader: startup the tpm device when installing the protocol")
Reviewed-by: Heinrich Schuchardt <[email protected]>
Signed-off-by: Ilias Apalodimas <[email protected]>
|
|
We currently return 'No space left on device' if the eventlong buffer
we allocated is not enough. On a similar check later on that function
during the call to tcg2_log_init() we return 'No buffer space
available'. So switch both error codes to -ENOBUFS since we are always
checking a buffer and not a device.
Fixes: commit 97707f12fdab ("tpm: Support boot measurements")
Reviewed-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Ilias Apalodimas <[email protected]>
|
|
|
|
https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request doc-2024-07-rc5-2
Documentation:
* Fix broken references to pytest suite and test writing
* Fix links to FIT documentation
* Add capsule documentation for TI K3 devices
|
|
Added introductory documentation about capsule support for TI devices,
including links to more detailed information.
Also added a note in the build secction that points to the host package
dependency docs.
This patch is followup from a request in the series introducing capsule
update for TI boards.
https://lore.kernel.org/r/20240618145058.552eapp5iiz772ej@hardcore
Signed-off-by: Jonathan Humphreys <[email protected]>
|
|
Add missing colon in :doc: link.
Fixes: fc3283314539 ("doc: Explain briefly how to write new tests")
Signed-off-by: Alexander Dahl <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
This should have been adapted directly with or after
v2021.01-693-gca6583d4e08 ("doc: move test/README to HTML
documentation") or v2021.01-694-g0157619d5c8 ("doc: move
test/py/README.md to HTML documentation") already.
Signed-off-by: Alexander Dahl <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Correct the links to the FIT documentation in boot/Kconfig.
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
Correct the links to the FIT documentation.
Signed-off-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Ilias Apalodimas <[email protected]>
|
|
Replace the outdated link.
Signed-off-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
support + typos"
Quentin Schulz <[email protected]> says:
bootflow menu currently crashes U-Boot with a NULL pointer dereference
because bootflow->dev is NULL for global bootmeths (such as EFI BOOTMGR).
Therefore, let's check if the bootflow is associated with a global
bootmeth before trying to make it part of the menu.
While this makes U-Boot not crash anymore, bootflow menu doesn't work
for me (I have never had a happy path with it, but I haven't actually
tried it before today :) ) and this was basically just implemented
following Simon's suggestion sent over IRC. No clue if this is enough or
just a quick band-aid patch.
This also fixes typos in multiple places.
|
|
Michal Simek <[email protected]> says:
Hi,
currently only DT way is supported and it is added directly to lib/smbios.c
but I think DT and env is only one way how information can be found that's
why this series is improving handling with using sysinfo driver which can
be platform specific.
At the end of day DT should be taken from smbios.c and put to sysinfo DT
driver instead of implementing it directly in this generic file.
|
|
The global bootmeths don't set the dev in bootflow struct which means
the dev_get_parent(bflow->dev) triggers a NULL-pointer dereference and
crash U-Boot.
So before trying to handle a bootflow, check that the associated
bootmeth isn't global, otherwise skip it.
Suggested-by: Simon Glass <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Code is pretty much supports only DT properties and completely ignore
information coming from sysinfo driver.
Code is calling smbios_add_prop() which calls with
smbios_add_prop_si(SYSINFO_ID_NONE). But SYSINFO_ID_NONE can't
differentiate different entries from sysinfo driver.
That's why introduce separate SYSINFO macros which can be used in sysinfo
driver and passed to smbios structure.
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
This fixes a few syntactic issues as well as typos and grammar.
Signed-off-by: Quentin Schulz <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
This fixes a handful of typos in various help texts in Kconfig configs.
Signed-off-by: Quentin Schulz <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
It's bootmeths and not bootmethds.
Signed-off-by: Quentin Schulz <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Currently code looks like that it sysinfo drivers are supported but
actually none checking that system is detected. That's why call
sysinfo_detect() to make sure that priv->detected in sysinfo uclass is
setup hence information from driver can be passed to smbios.
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
It is good to be aware what information is shared via smbios interface
that's why enable it by default.
Signed-off-by: Michal Simek <[email protected]>
|
|
Add the secondary cores nodes in the dts file
Signed-off-by: Harsimran Singh Tungal <[email protected]>
Cc: Tom Rini <[email protected]>
Cc: Rui Miguel Silva <[email protected]>
|
|
MD Danish Anwar <[email protected]> says:
This series adds config changes and env changes to enable ICSSG Ethernet
Driver on AM64x.
|
|
When ICSSG driver is enabled (CONFIG_TI_ICSSG_PRUETH=y) set
storage_interface and fw_dev_part env variables.
These variables need be set appropriately in order to load different
ICSSG firmwares needed for ICSSG driver. By default the storage
interface is mmc and the partition is 1:2. User can modify this based on
their needs.
Signed-off-by: MD Danish Anwar <[email protected]>
|
|
Enable ICSSG driver, DP83869 phy driver, REMOTEPROC and PRU_REMOTEPROC
in am64x_evm_a53_defconfig. All these configs are needed for ICSSG
driver.
Signed-off-by: MD Danish Anwar <[email protected]>
|
|
If multiple weak implementations of a weak function exist, it is unclear
which one the linker should chose. cmd/cache.c already defines a weak
invalidate_icache_all().
We don't need a call to invalidate_icache_all() on x86.
ARM, RISC-V, and Sandbox provide an implementation.
Signed-off-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Ilias Apalodimas <[email protected]>
|
|
In EFI sub-system we rely on invalidate_icache_all() to invalidate the
instruction cache after loading binaries. Add the missing implementation on
ARM1136, ARM1176.
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
Jayesh Choudhary <[email protected]> says:
Hello there,
This series add the U-Boot support for our new platform of K3-SOC
family - J722S-EVM which is a superset of AM62P. It shares the same
memory map and thus the nodes are being reused from AM62P includes
instead of duplicating the definitions.
Some highlights of J722S SoC (in addition to AM62P SoC features) are:
- Two Cortex-R5F for Functional Safety or general-purpose usage and
two C7x floating point vector DSP with Matrix Multiply Accelerator
for deep learning.
- Vision Processing Accelerator (VPAC) with image signal processor
and Depth and Motion Processing Accelerator (DMPAC).
- 7xUARTs, 3xSPI, 5xI2C, 2xUSB2, 2xCAN-FD, 3xMMC and SD, GPMC for
NAND/FPGA connection, OSPI memory controller, 5xMcASP for audio,
4xCSI-RX for Camera, 1 PCIe Gen3 controller, USB3.0 eCAP/eQEP,
ePWM, among other peripherals.
TRM: <https://www.ti.com/lit/zip/sprujb3>
Schematics: <https://www.ti.com/lit/zip/sprr495>
Boot test log:
<https://gist.github.com/Jayesh2000/0313e58fde377f877a9a8f1acc2579ef>
|
|
Introduce basic documentation for the J722S-EVM.
Signed-off-by: Jayesh Choudhary <[email protected]>
Reviewed-by: Neha Malcom Francis <[email protected]>
|
|
Introduce the initial configs needed to support the J722S SoC family.
Signed-off-by: Vaishnav Achath <[email protected]>
Signed-off-by: Jayesh Choudhary <[email protected]>
|
|
Include the uboot device tree files needed to boot the board.
Co-developed-by: Vaishnav Achath <[email protected]>
Signed-off-by: Vaishnav Achath <[email protected]>
Signed-off-by: Jayesh Choudhary <[email protected]>
|
|
Include the static DMA channel data for using DMA at SPL stage
for J722S SoC family.
Signed-off-by: Vaishnav Achath <[email protected]>
Signed-off-by: Jayesh Choudhary <[email protected]>
|
|
Introduce the basic files needed to support the TI J722S family of SoCs.
Co-developed-by: Vaishnav Achath <[email protected]>
Signed-off-by: Vaishnav Achath <[email protected]>
Signed-off-by: Jayesh Choudhary <[email protected]>
|
|
Introduce the basic functions and definitions needed to properly
initialize TI J722S family of SoCs.
Co-developed-by: Vaishnav Achath <[email protected]>
Signed-off-by: Vaishnav Achath <[email protected]>
Signed-off-by: Jayesh Choudhary <[email protected]>
|
|
The J722S family of SoCs uses the same DDR controller as found on the
AM62A family. Enable this option when building for the J722S family.
Signed-off-by: Vaishnav Achath <[email protected]>
Signed-off-by: Jayesh Choudhary <[email protected]>
Reviewed-by: Neha Malcom Francis <[email protected]>
|
|
Include the clock and lpsc tree files needed for the wkup spl to
initialize the proper PLLs and power domains to boot the SoC.
Reviewed-by: Bryan Brattlof <[email protected]>
Signed-off-by: Vaishnav Achath <[email protected]>
Signed-off-by: Jayesh Choudhary <[email protected]>
|
|
Add the entries in alphabetical order.
Signed-off-by: Jayesh Choudhary <[email protected]>
Reviewed-by: Neha Malcom Francis <[email protected]>
|
|
Add the power domain platform data entries in alphabetical order.
Signed-off-by: Jayesh Choudhary <[email protected]>
Reviewed-by: Neha Malcom Francis <[email protected]>
|
|
Use IS_ENABLED macro for the platform clock-data list and add them
in alphabetical order.
Reviewed-by: Bryan Brattlof <[email protected]>
Signed-off-by: Jayesh Choudhary <[email protected]>
|
|
Include the part number for TI's j722s family of SoC
to identify it during boot.
Signed-off-by: Vaishnav Achath <[email protected]>
Signed-off-by: Jayesh Choudhary <[email protected]>
|
|
Add JTAG_ID_PARTNO_* in alphabetical order.
Signed-off-by: Jayesh Choudhary <[email protected]>
Reviewed-by: Neha Malcom Francis <[email protected]>
|
