| Age | Commit message (Collapse) | Author |
|---|
|
When som_type does not match any case, it is uninitialized and the
function still tries to print the SoM info. Rather, this is an error
condition and the function should abort prematurely. Highlight this by
printing an error message and returning early.
Signed-off-by: Yannic Moog <[email protected]>
|
|
Move all function definitions in {phytec|imx8m}_som_detection from the
header to the source file to prevent potential linker error regarding
multiple definitions. Also move the #if blocks with the definitions.
Signed-off-by: Yannic Moog <[email protected]>
|
|
In phytec_eeprom_data_init, after reading eeprom data into buffer, it is
checked whether all bytes are 0x0 by iterating over chunks of the
buffer. The offset, or index of the chunk, was never changed, leading to
repeated comparison of only the first chunk. Use array notation and
access chunk via array index to compare all chunks of the buffer.
Signed-off-by: Yannic Moog <[email protected]>
|
|
Pointer in phytec_imx8m_detect was accessed without checking it first.
Fix this by moving the pointer check in front of any accesses.
Signed-off-by: Yannic Moog <[email protected]>
|
|
phytec_imx8m_detect returns -1 on error, but the return type is u8
leading to 255 return values. Fix this by changing the return type to
int; there is no reason to keep it as u8 .
Signed-off-by: Yannic Moog <[email protected]>
|
|
Enable call to arch_misc_init in order to probe the CAAM driver.
Signed-off-by: Tim Harvey <[email protected]>
|
|
Add the TPM device found on the GW72xx revision F PCB.
This hangs off of SPI2, uses gpio1_10 as a CS and gpio1_11 as RST#.
Signed-off-by: Tim Harvey <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
Add the TPM device found on the GW72xx revision F PCB.
This hangs off of SPI2, uses gpio1_10 as a CS and gpio1_11 as RST#.
Signed-off-by: Tim Harvey <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
Incorrect registers HW_POWER_VDDIOCTRL, HW_POWER_VDDACTRL
and HW_POWER_VDDDCTRL are used in the current code to disable/enable
brownout interrupts in 'mxs_power_set_vddx()'.
Change register to HW_POWER_CTRL which contains brownout interrupt
enable bits ENIRQ_VDDIO_BO, ENIRQ_VDDA_BO and ENIRQ_VDDD_BO.
Signed-off-by: Cody Green <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Lukasz Majewski <[email protected]>
|
|
The command completion temporary buffer seems to be only
used by the argv tokenizer, move it to stack. This saves
2 kiB from the binary size (depends on configuration) per:
$ aarch64-linux-gnu-readelf -s u-boot | sort -n -k 3
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
The history buffer is currently a static array which can be some
10-40 kiB depending on configuration, and so adds considerably to
the U-Boot binary size. Allocate it dynamically instead to reduce
the U-Boot binary size.
Signed-off-by: Marek Vasut <[email protected]>
|
|
This is supposed to be supported by the 'bootflow cmd' command, at
least according to the help. There is a 'bootflow cmd clear' but it is
often more intuitive to use 'bootcmd cmd set' with an empty value.
Update the command to pass BOOTFLOWCL_EMPTY in this case.
Signed-off-by: Simon Glass <[email protected]>
|
|
Commit 51bb33846ad2 ("bootm: Support string substitution in
bootargs") introduced a feature of bootargs string substitution
and changed a flag used in bootm_process_cmdline_env() call
to be either true or false. With this flag value,
condition in bootm_process_cmdline()
`if (flags & BOOTM_CL_SUBST)` is never true
and process_subst() is never called.
Add a simple test to verify if substitution works OK.
Signed-off-by: Piotr Kubik <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
The `afs load` command copies data to RAM. Set the filesize
environment variable to record how much data was 'loaded'
Signed-off-by: Robert Catherall <[email protected]>
Reviewed-by: Andre Przywara <[email protected]>
Tested-by: Andre Przywara <[email protected]>
|
|
pkcs11 : change engine uri to use full pk11-URI as defined in:
https://www.rfc-editor.org/rfc/rfc7512.html
Signed-off-by: Ayoub Zaki <[email protected]>
|
|
Specify max gunzip size from config to override SYS_XIMG_LEN
default value wich is 0x800000. In case we have a large portion of FIT
image, for example gzipped kernel with decompressed size large than
0x800000 we should enlarge imxract area, otherwise extracting it will
fail.
It used to be a hardcoded define in cmd/ximg.c and we are moving it to
config.
Signed-off-by: Nikita Shubin <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-amlogic into next
- Add support for new GXL MDIO mux, with driver and Linux DT sync from v6.4
|
|
https://source.denx.de/u-boot/custodians/u-boot-tegra into next
This PR contains 4 patchsets:
1. PMIC GPIO cells bringup. Created drivers for MAX7663 and Palmas
PMICs and gpio-uclass patch isolated behind configs for these 2
drivers. No unintentional size increase on any board. (proposed
2023-11-06 without any reaction)
2. Simple PLL clocks support in common tegra clock code which allows
use of simple PLL the same way main PLLs are used (before only
clock_start_pll was available). PLLD2 is an example of simple PLL, it
is used as a video subsystem parent clock and was used to test this
code. So far everything worked as expected. (proposed 2023-11-16
without any reaction)
3. A small patch for tegra emmc to allow pass max frequency from
device tree since some devices may not support full speed.
4. Pinmux DM conversion. Patchset consists of commit with DM wrapper
for existing pinmux code for t20/t30/t114, pinmux and funcmux files
relocation into a dedicated folder inside pinctrl, conversion of some
tegra boards to device tree pinmux setup.
|
|
Since implementation of pinctrl driver for T20 Paz00 can switch
to device tree pinmux setup along with remove of board pinmux
and some minor device tree and defconfig tweaks.
Tested-by: Agneli <[email protected]> # Toshiba AC100 T20
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
Drop the pinmux setup in the board in favor of setting it up in
the device tree. Device tree nodes match nodes used for the Linux
device tree and are set according to the downstream kernel.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
Drop the pinmux setup in the board in favor of setting it up in
the device tree. Device tree nodes match nodes used in the Linux
device tree.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
Drop the pinmux setup in the board in favor of setting it up in
the device tree. Device tree nodes match nodes used for the Linux
device tree and are set according to the service manual.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
Drop the pinmux setup in the board in favor of setting it up in
the device tree. Device tree nodes match nodes used in the Linux
device tree.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
Move all existing pinmux and funcmux code into a dedicated folder in
pinctrl to simplify further maintenance.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
The existing pinctrl driver available for Tegra SOC is well
designed, but it lacks DM support. Let's add a DM compatible
overlay, which allows use of the device tree, along with preserving
backward compatibility with all existing setups and the ability
to use it in SPL board configuration stage.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
SPL configs are used only by the ARMv7-based Tegra SOC's, so move
SPL_SYSRESET under TEGRA_ARMV7_COMMON selection and enable SPL_DM
since SPL_SYSRESET depends on it.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
The driver currently hard-codes the max freqency for the sdhci
controllers. If the controller is unable to operate at the max
frequency, the mmc card will not be available on the first scan.
Subsequent scans will eventually find a working combination.
Fix this by allowing the driver to check for the max-frequency
property and default to the original value if it doesn't exist.
Signed-off-by: Peter Geis <[email protected]>
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
PLLD2 is a simple clock (controlled by 2 registers) and appears starting
from T30. Primary use of PLLD2 is as main HDMI clock parent.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
PLLD2 is a simple clock (controlled by 2 registers) and appears starting
from T30. Primary use of PLLD2 is as main HDMI clock parent.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
Simple PLL clocks like PLLD2 were omitted since they do not share common
4 register structure with main clocks. Such clocks are containd in simple
PLL group. Only clock_start_pll function supported them. This patch expands
this support on clock_set_rate and clock_get_rate which should make
simple PLL clocks equal to main PLL clocks.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
UCLASS_PMIC may have GPIO children without exposed fdt node,
in this case if requesting fails, check if uclass is PMIC.
Restrict build for supported devices only to save those precious
bytes on devices with no spare memory.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
Add gpio driver for TI Palmas series PMIC. This has 8 gpio which can
work as input/output.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
MAXIM Semiconductor's PMIC, MAX77663 has 8 GPIO pins and 3 GPIO-like
pins. It also supports interrupts from these pins.
Add GPIO driver for these pins to control via GPIO APIs.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
Reid Tonking <[email protected]> says:
Since the 09.01.00.002 release of ti-linux-firmware [0] upstream uboot
has led to the kernel hanging during boot [1] for the TI J7200 S0C. The
issue was found to be a few patches that had be added to ti-u-boot, but not
yet upstreamed. This series adds the missing two patches to allow upstream
u-boot to boot the kernel properly [2].
[0] https://git.ti.com/cgit/processor-firmware/ti-linux-firmware/commit/?h=ti-linux-firmware-next&id=952fd03e36a50ec070e73560dc1060102d637ce0
Boot logs:
[1] https://gist.github.com/reidt1/5f4e85a0db258bcf20d7168bd0caebd0
[2] https://gist.github.com/reidt1/e950dc97f15ad0a09623d64f81edac39
Links to patches on ti-u-boot:
https://git.ti.com/cgit/ti-u-boot/ti-u-boot/commit/?h=ti-u-boot-2023.04-next&id=d878fbef4d4460e87608d8d2dfe5311499de49c5
https://git.ti.com/cgit/ti-u-boot/ti-u-boot/commit/?h=ti-u-boot-2023.04-next&id=543e735fe495be233a8a75b19b3d7f8ed44251e0
|
|
Julien Masson <[email protected]> says:
This patch series add the support for the MediaTek MT8365 EVK Board [1].
Most of the code have been copied/adapted from Linux tag v6.7-rc2.
For now we only enable/test these features:
Boot, UART, Watchdog and MMC.
[trini: This includes two clocks not listed in the Linux binding, which
needs resyncing later]
|
|
- Assorted platform updates for TI K3, vexpress64, mediatek and related
cleanups to the DW GPIO driver and OPTEE
|
|
Previously, dynamic frequency scaling supported rates only through fixed
divison.
This virtual clock mux configuration enables more varied rates on A72
clock ID 202 by setting up the required register.
Reviewed-by: Udit Kumar <[email protected]>
Signed-off-by: Apurva Nandan <[email protected]>
Signed-off-by: Reid Tonking <[email protected]>
|
|
In order for the Cortex-A72s to operate at different frequencies other
than the default 2GHz, add in a new 'virtual' mux (a mux that does not
physically exist in the clock tree) that can be selected.
CC: Vishal Mahaveer <[email protected]>
Signed-off-by: Bryan Brattlof <[email protected]>
Signed-off-by: Apurva Nandan <[email protected]>
Signed-off-by: Reid Tonking <[email protected]>
Reviewed-by: Udit Kumar <[email protected]>
|
|
This adds support for the MT8365 EVK board with the following
features enabled/tested: Boot, UART, Watchdog and MMC.
Signed-off-by: Julien Masson <[email protected]>
|
|
This adds the pinctrl bindings for Mediatek MT8365 SoC based on the
dt-bindings in Linux tag v6.7-rc2.
(commit 8b4c397d88d97d4fd9c3f3527aa66688b1a3387a)
Signed-off-by: Julien Masson <[email protected]>
|
|
This patch adds basic support for MediaTek MT8365 SoC.
The dtsi has been copied from Linux source code tag v6.7-rc2.
(commit 9b5d64654ea8f51fe1e8e29ca1777b620be8fb7c)
Signed-off-by: Julien Masson <[email protected]>
|
|
Add power-domain header for MediaTek MT8365 SoC copied from Linux
source code tag v6.7-rc2.
(commit a1571f1f333c2fced076f0d54ed771d1838d827f)
Signed-off-by: Julien Masson <[email protected]>
Reviewed-by: Mattijs Korpershoek <[email protected]>
|
|
This patch adds clock driver support for MediaTek MT8365 SoC.
The changes are based on the Linux source code tag v6.7-rc2.
clk-mt8365.c has been written based on these kernel files:
- clk-mt8365.c (a96cbb146a9736f501fe66ebda6a9018735e5e8a)
- clk-mt8365-apmixedsys.c (65c9ad77cbc0eed78db94d80041aba675cfbdfa9)
And adapted following the clk attributes supported by U-Boot.
Signed-off-by: Julien Masson <[email protected]>
Reviewed-by: Mattijs Korpershoek <[email protected]>
|
|
This adds the clock bindings for Mediatek MT8365 SoC based on the
dt-bindings in Linux tag v6.7-rc2.
(commit c61978175ac1337f028ac1f956666f16db84f4e5)
Signed-off-by: Julien Masson <[email protected]>
Reviewed-by: Mattijs Korpershoek <[email protected]>
|
|
spl_mmc_emmc_boot_partition return a number different from 0
if the partition is a boot one. We can have the uboot img
for instance in a raw offset in emmc partition 0 so we would
like to continue to load the next stage. If the user want
to use EMMC as boot device allow him to use any part of the
emmc and not only boot partition
Signed-off-by: Michael Trimarchi <[email protected]>
|
|
The block count limit on MMC based devices should be set according to
CONFIG_SYS_MMC_MAX_BLK_COUNT instead of hardcoding value.
Signed-off-by: Julien Masson <[email protected]>
|
|
Drop headers which are not used or needed in this file.
Signed-off-by: Maksim Kiselev <[email protected]>
|
|
Change optee driver service enumeration to not enumerate (and
allocate a zero sized shared memory buffer) when OP-TEE
reports that there is no service to enumerate.
This change fixes an existing issue that occurs when the such zero
sized shared memory buffer allocated from malloc() has a physical
address of offset 0 of a physical 4kB page. In such case, OP-TEE
secure world refuses to register the zero-sized shared memory
area and makes U-Boot optee service enumeration to fail.
Fixes: 94ccfb78a4d6 ("drivers: tee: optee: discover OP-TEE services")
Signed-off-by: Etienne Carriere <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
Reviewed-by: Jens Wiklander <[email protected]>
|
|
Change optee probe function to only warn when service enumeration
sequence fails instead of reporting an optee driver probe failure.
Indeed U-Boot can still use OP-TEE even if some OP-TEE services are
not discovered.
Fixes: 94ccfb78a4d6 ("drivers: tee: optee: discover OP-TEE services")
Signed-off-by: Etienne Carriere <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
Reviewed-by: Jens Wiklander <[email protected]>
|
|
DSP core is going into abnormal state when load callback is called
after starting of DSP core.
Reload of firmware needs core to be stopped first, followed by
load.
So avoid loading of firmware, when core is started.
Signed-off-by: Udit Kumar <[email protected]>
|
