| Age | Commit message (Collapse) | Author |
|---|
|
CONFIG_NVME=y without CONFIG_NVME_PCI=y does not provide working NVMe
support. Instead of implying CONFIG_NVME we must imply CONFIG_NVME_PCI
which will select CONFIG_NVME.
Fixes: e64db0d92e32 ("riscv: qemu: Enable e1000 and nvme support")
Signed-off-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Mark Kettenis <[email protected]>
|
|
Enables StarFive Watchdog driver and WDT command.
Signed-off-by: Chanho Park <[email protected]>
Reviewed-by: Leo Yu-Chi Liang <[email protected]>
|
|
Adds jh7110 watchdog device tree node.
Signed-off-by: Chanho Park <[email protected]>
Reviewed-by: Leo Yu-Chi Liang <[email protected]>
|
|
Add to support StarFive watchdog driver. The driver is imported from
linux kernel's drivers/watchdog/starfive-wdt.c without jh7100 support
because there is no support of jh7100 SoC in u-boot yet.
Howver, this patch has been kept the variant coding style because JH7100
can be added later and have a consistency with the linux driver.
Signed-off-by: Chanho Park <[email protected]>
Reviewed-by: Leo Yu-Chi Liang <[email protected]>
|
|
Add JH7110_SYSCLK_WDT_APB and JH7110_SYSCLK_WDT_CORE clocks for JH7110
watchdog device.
Signed-off-by: Chanho Park <[email protected]>
Reviewed-by: Leo Yu-Chi Liang <[email protected]>
|
|
Prepare v2024.01-rc4
# -----BEGIN PGP SIGNATURE-----
#
# iQGzBAABCgAdFiEEGjx/cOCPqxcHgJu/FHw5/5Y0tywFAmVuHrwACgkQFHw5/5Y0
# tyy3Tgv+LB/X0ZR3IHnu1mvQ7kpOFvAjjKr0BUpcEEzsrDZeJnS6sy06m+REez2E
# UmuLeKFj5NUCYXNKtxn2+gVnJt8Tk6ftxhMTiZHmR4Y4NVc5aPtqYmVsv6Q29j0U
# mcg7AGcZTniu9/naNM+ZcDeHzLDAB0whmE9eVfixXVgyitILoLHNdFiQ7W4oR7Kh
# /mBgdMDBS3rqiRi6CuqKUnl4ADX8T3AXaSfi3hqOC5Pj+HPkZSUfyWx31mu9mN1D
# wXTHASZX06Dop25fm/ZSdWk1blBw29WqRiJBdwNatvyC5pqMsotTvAfH2AcHBEYg
# tpoper+WDOBAipt6b6Y1B7q4VPvJ97L9dFCAYqN0nGCe+rkdi+k+cly7M6Ye9xLt
# e7rVUfnKgIMP8jkLcVBYoWkFY5FiJ82O5qjoF5N3dAuHeWacDFsB5TugDTOQvblH
# LWCmcIyU1N9Ma/Ib0rTvNduvpBUYBKXYlD1+rjPZUbTUnfc79mf+ReFpcoW6Kxh+
# bkz81p8P
# =ebIZ
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 04 Dec 2023 01:47:24 PM EST
# gpg: using RSA key 1A3C7F70E08FAB1707809BBF147C39FF9634B72C
# gpg: Good signature from "Thomas Rini <[email protected]>" [ultimate]
|
|
commit 239d59a65e20 ("efi_loader: reconnect drivers on failure")
tried to fix the UninstallProtocol interface which must reconnect
any controllers it disconnected by calling ConnectController()
in case of failure. However, the reconnect functionality was wired in
efi_disconnect_all_drivers() instead of efi_uninstall_protocol().
As a result some SCT tests started failing.
Specifically, BBTestOpenProtocolInterfaceTest333CheckPoint3() test
- Calls ConnectController for DriverImageHandle1
- Calls DisconnectController for DriverImageHandle1 which will
disconnect everything apart from TestProtocol4. That will remain
open on purpose.
- Calls ConnectController for DriverImageHandle2. TestProtocol4
which was explicitly preserved was installed wth BY_DRIVER attributes.
The new protocol will call DisconnectController since its attributes
are BY_DRIVER|EXCLUSIVE, but TestProtocol4 will not be removed. The
test expects EFI_ACCESS_DENIED which works fine.
The problem is that DisconnectController, will eventually call
EFI_DRIVER_BINDING_PROTOCOL.Stop(). But on the aforementioned test
this will call CloseProtocol -- the binding protocol is defined in
'DBindingDriver3.c' and the .Stop function uses CloseProtocol.
If that close protocol call fails with EFI_NOT_FOUND, the current code
will try to mistakenly reconnect all drivers and the subsequent tests
that rely on the device being disconnected will fail.
Move the reconnection in efi_uninstall_protocol() were it belongs.
Fixes: commit 239d59a65e20 ("efi_loader: reconnect drivers on failure")
Signed-off-by: Ilias Apalodimas <[email protected]>
Reviewed-by: Heinrich Schuchardt <[email protected]>
|
|
ACPI tables cannot convey memory reservations for ARM and RISC-V.
x86 uses the BIOS E820 table for this purpose. We cannot simply ignore the
device-tree when booting via ACPI. We have to assign EfiReservedMemory
according to the prior stage device-tree ($fdtaddr) or as fallback the
control device-tree ($fdtcontroladdr).
Signed-off-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
The printf() %pU option decodes GUIDs so it is not necessary to do this
first. Drop the incorrect code.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Ilias Apalodimas <[email protected]>
Reviewed-by: Heinrich Schuchardt <[email protected]>
|
|
Locate these so that they can be displayed using the 'acpi' command.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Heinrich Schuchardt <[email protected]>
|
|
The current build system embeds the EFI Signature List(ESL)
into the dtb to be used in the EFI capsule authentication.
This ESL file is specified through the CONFIG_EFI_CAPSULE_ESL_FILE
Kconfig option. If CONFIG_EFI_CAPSULE_ESL_FILE is not specified,
U-boot build ends up with failure but the cause of failure is not
easily understandable. Current error message is as follows.
FATAL ERROR: Error reading file into data: Is a directoryCheck /home/ubuntu/src/ledge/u-boot/arch/arm/dts/.synquacer-sc2a11-developerbox.dtb.pre.tmp for errors
make[2]: *** [scripts/Makefile.lib:355: arch/arm/dts/synquacer-sc2a11-developerbox.dtb] Error 1
make[1]: *** [dts/Makefile:44: arch-dtbs] Error 2
make: *** [Makefile:1165: dts/dt.dtb] Error 2
make: *** Waiting for unfinished jobs....
This commit shows the error message that CONFIG_EFI_CAPSULE_ESL_FILE
must be specified when the EFI capsule authentication is enabled, then
terminate the build with error.
Signed-off-by: Masahisa Kojima <[email protected]>
Reviewed-by: Weizhao Ouyang <[email protected]>
|
|
This is a common typo listed in scripts/spelling.txt. Fix it to match the
patchwork status, which is superseded.
Signed-off-by: Mattijs Korpershoek <[email protected]>
Reviewed-by: Heinrich Schuchardt <[email protected]>
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
At this point, clang can be used on both 32bit and 64bit targets without
issue. Make note of logic we have that will inform clang of the
architecture to build for.
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Heinrich Schuchardt <[email protected]>
|
|
Fix the devicetree used with sandbox. This is needed because the
default (full) devicetree must be used by all phases of boot, with
sandbox.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Heinrich Schuchardt <[email protected]>
|
|
Signed-off-by: Tom Rini <[email protected]>
|
|
We currently use an outdated format 32-bit format for SMBIOS tables.
So we must allocate SMBIOS tables below 4 GiB.
Signed-off-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Ilias Apalodimas <[email protected]>
Tested-by: Ilias Apalodimas <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-watchdog
- Correct watchdog timeout print message (Chanho Park)
|
|
The wdt_start function takes timeout_ms as a parameter and starts the
watchdog with this value. However, when you output the message, it shows
the default timeout value for the watchdog device.
So this patch fixes that part to output the correct timeout value.
Before -->
StarFive # wdt start 3000
WDT: Started watchdog@13070000 without servicing (60s timeout)
After -->
StarFive # wdt start 3000
WDT: Started watchdog@13070000 without servicing (3s timeout)
Fixes: c2fd0ca1a822 ("watchdog: Integrate watchdog triggering into the cyclic framework")
Signed-off-by: Chanho Park <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-sh
|
|
- USB XHCI fixes
|
|
As requirement of CR side, QSPI Flash usage via RPC driver shall
be disabled and leaving the control of this module to CR side.
Perform DT modification to disable the RPC SPI.
Reviewed-by: Marek Vasut <[email protected]>
Signed-off-by: Cong Dang <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
[Marek: Do not modify defconfig, modify the DT instead, this way
the RPC SPI can be enabled without recompiling the U-Boot
itself. Update commit message accordingly.]
|
|
Use the phandle reference to &rpc node in arch/arm/dts/r8a779g0.dtsi
and remove properties which are already in arch/arm/dts/r8a779g0.dtsi.
No functional change and no resulting DT change.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Compiling with CONFIG_USB_XHCI_PCI and CONFIG_PCI=n results in
usb/host/xhci-pci.c:48:(.text.xhci_pci_probe+0x44):
undefined reference to `dm_pci_write_config32
Add the missing Kconfig dependency.
Signed-off-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Mark Kettenis <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
Like Rockchip RK3328 and RK3568, the RK3588 also have a single node to
represent the glue and ctrl for USB 3.0.
Use rk_ops as driver data to select correct ctrl node for RK3588 DWC3.
Signed-off-by: Jonas Karlman <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
USB UFI uses fixed 12-byte commands (as does RBC, which is not
supported), but SCSI does not have this limitation. Use the correct
command block lengths depending on the subclass.
Signed-off-by: Hector Martin <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
Some devices like YubiKeys need more time before SET_ADDRESS. The spec
says we need to wait 10ms.
Signed-off-by: Hector Martin <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
We need to get the DMA address before incrementing the pointer, as that
might move us onto another segment.
Signed-off-by: Hector Martin <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
Now that we always check the return value, just return NULL on timeouts.
We can still log the error since this is a problem, but it's not reason
to panic.
Signed-off-by: Hector Martin <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
This isn't going to work, don't pretend it will and then end up timing
out.
Signed-off-by: Hector Martin <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
There is currently no codepath to recover from this case. In principle
we could require that the upper layer do this explicitly, but let's just
do it in xHCI when the next bulk transfer is started, since that
reasonably implies whatever caused the problem has been dealt with.
Signed-off-by: Hector Martin <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
There is a race where an endpoint may halt by itself while we are trying
to halt it, which results in a context state error. See xHCI 4.6.9 which
mentions this case.
This also avoids BUGging when we attempt to stop an endpoint which was
already stopped to begin with, which is probably a bug elsewhere but
not a good reason to crash.
Signed-off-by: Hector Martin <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
If the xHC has a problem with our STOP ENDPOINT command, it is likely to
return a completion directly instead of first a transfer event for the
in-progress transfer. Handle that more gracefully.
We still BUG() on the error code, but at least we don't end up timing
out on the event and ending up with unexpected event errors.
Signed-off-by: Hector Martin <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
xhci_wait_for_event returns NULL on timeout, so the caller always has to
check for that. This addresses immediate explosions in this part
of the code when timeouts happen, but not the root cause for the
timeout.
Signed-off-by: Hector Martin <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-tegra into next
Device tree improvents for Paz00 and DM PMIC convertion of recently
merged Tegra boards.
|
|
- Add a TFTP put test, a few TI Keystone 2 updates, fix stack-protector
for PowerPC, fixes in lib/slre, timer-uclass and pvblock.
|
|
Signed-off-by: Andrew Davis <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
This is a hacky way to have this file included in all source files that
include common.h, instead just include from the files that need it.
Signed-off-by: Andrew Davis <[email protected]>
|
|
These are leftover definitions. While here cleanup some leftover comments.
Signed-off-by: Andrew Davis <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
On powerpc, stack protector expects a function called
__stack_chk_fail_local() instead of __stack_chk_fail()
And some versions of GCC for powerpc default to TLS canary
instead of global canary, so always force GCC to use global
canary with -mstack-protector-guard=global
Cc: Joel Peshkin <[email protected]>
Fixes: 4e9bce12432 ("Add support for stack-protector")
Signed-off-by: Christophe Leroy <[email protected]>
|
|
The current implementation may cause BUG_ON() in blkfront_aio()
BUG_ON(n > BLKIF_MAX_SEGMENTS_PER_REQUEST);
In pvblock_iop(), a read/write operation will be split into smaller
chunks of data so that the size in one access (aio_nbytes) is limited
to, at the maximum,
BLKIF_MAX_SEGMENTS_PER_REQUEST * PAGE_SIZE
But this works only if when the *buffer* passed in to pvblock_io()
is page-aligned. If not, the given data region may stand across
(BLKIF_MAX_SEGMENTS_PER_REQUEST + 1) pages. See the logic in
blkfront_aio():
start = (uintptr_t)aiocbp->aio_buf & PAGE_MASK;
end = ((uintptr_t)aiocbp->aio_buf + aiocbp->aio_nbytes +
PAGE_SIZE - 1) & PAGE_MASK;
Then this will lead to BUG_ON() above.
This can be fixed by decreasing the maximum size of aio_nbytes.
Signed-off-by: AKASHI Takahiro <[email protected]>
Fixes: commit 3a739cc6c948 ("xen: pvblock: Implement front-back protocol and do IO")
|
|
Currently the "clock-frequency" DT property is only being considered as an
fallback if either there is no clock driver, the clock driver implements
the request-op correctly or there is no clock defined for the timer at all.
This patch makes "clock-frequency" also being picked as a fallback if
getting the clock-rate fails, since clk_get(_by_index) will return no
error, if a clock driver does not implement the request-op and does also
not support getting the rate of the clock in question.
timer_post_probe will take care if the property does not exist in the DT or
is defined as 0.
Signed-off-by: Alex Bee <[email protected]>
|
|
Signed-off-by: Francois Berder <[email protected]>
|
|
Execute tftpput command for uploading files to a server and validate its
size & CRC32.
Signed-off-by: Love Kumar <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
To quote the author:
"Scmi" command will be re-introduced per Michal's request.
The functionality is the same as I put it in my patch set of adding
SCMI base protocol support, but made some tweak to make UT, "ut dm
scmi_cmd," more flexible and tolerable when enabling/disabling a specific
SCMI protocol for test purpose.
Each commit may have some change history inherited from the preceding
patch series.
Test
====
The patch series was tested on the following platforms:
* sandbox
|
|
In this test, "scmi" command is tested against different sub-commands.
Please note that scmi command is for debug purpose and is not intended
in production system.
Signed-off-by: AKASHI Takahiro <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Etienne Carriere <[email protected]>
|
|
This is a help text for scmi command.
Signed-off-by: AKASHI Takahiro <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Etienne Carriere <[email protected]>
|
|
This command, "scmi", may provide a command line interface to various SCMI
protocols. It supports at least initially SCMI base protocol and is
intended mainly for debug purpose.
Signed-off-by: AKASHI Takahiro <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Etienne Carriere <[email protected]>
|
|
This change will be useful when we manually test SCMI on sandbox
by enabling/disabling a specific SCMI protocol.
Signed-off-by: AKASHI Takahiro <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
This is a precautionary change to make scmi tests workable whether or not
a specific protocol be enabled. If a given protocol is not configured,
we skip the test by returning -EAGAIN.
Signed-off-by: AKASHI Takahiro <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
To quote the author:
This series fixes an issue where the FAT type (FAT12, FAT16) is not
correctly detected, e.g. when the BPB field BS_FilSysType contains the
valid value "FAT ".
This issue occures, for example, if a partition is formatted by
swupdate using its diskformat handler. swupdate uses the FAT library
from http://elm-chan.org/fsw/ff/ internally.
See https://groups.google.com/g/swupdate/c/7Yc3NupjXx8 for a
discussion in the swupdate mailing list.
Please refer to the commit messages for more details.
1. Added bootsector checks
Most tests from https://www.win.tue.nl/~aeb/linux/fs/fat/fat-2.html
are added in the commit 'fs: fat: add bootsector validity check'.
Only the tests VIII, IX and X are not implemented.
I also checked the Linux kernel code (v6.6) and did not find any
checks on 'vistart->fs_type'. This is the reason why is skipped them
here.
See section '2. Size comparisons' for the impact on the binary size.
2. Size comparisons
I executed bloat-o-meter from the Linux kernel for an arm64
target (config xilinx_zynqmp_mini_emmc0_defconfig):
Comparison of the binary spl/u-boot-spl between master (rev
e17d174773e9ba9447596708e702b7382e47a6cf) and this patch
series (including the added validity checks of the boot sector):
add/remove: 0/0 grow/shrink: 1/1 up/down: 100/-12 (88)
Function old new delta
read_bootsectandvi 308 408 +100
fat_itr_root 444 432 -12
Total: Before=67977, After=68065, chg +0.13%
When compare the size of the binary spl/u-boot-spl between master this
series without the the validity checks of the boot sector:
add/remove: 0/0 grow/shrink: 0/2 up/down: 0/-24 (-24)
Function old new delta
read_bootsectandvi 308 296 -12
fat_itr_root 444 432 -12
Total: Before=67977, After=67953, chg -0.04%
So the size of the spl on this arm64 target increases by 88 bytes for
this series. When i remove the validity check the size decreases by 24 bytes.
|
