| Age | Commit message (Collapse) | Author |
|---|
|
We need the UT_TESTF_SCAN_FDT flag set for these tests to run with flat
tree. In some cases it is missing, so add it.
Signed-off-by: Simon Glass <[email protected]>
|
|
Follow the order used by memcpy() as it may be less confusing.
Signed-off-by: Simon Glass <[email protected]>
|
|
The bloblist should not be finalised until the image is fully set up.
This allows any final handoff information to be included in the bloblist.
Signed-off-by: Simon Glass <[email protected]>
|
|
Rather than open-coding the property names, use the existing constants
provided for this purpose. This better aligns the simple-FIT code with
the full FIT implementation.
Signed-off-by: Simon Glass <[email protected]>
|
|
For some reason this code was put in the main spl.c file. Move it out
to the FIT implementation where it belongs.
Signed-off-by: Simon Glass <[email protected]>
|
|
We have two functions called spl_load_fit_image(), one in spl.c and one in
spl_fit.c
Rename the second one, to indicate that it relates to simple FIT parsing,
rather than the full version.
Signed-off-by: Simon Glass <[email protected]>
|
|
This feature has some helpers in its header file so that its functions
resolve to nothing when the feature is disabled. Add a few more and use
these to simplify the code.
With this there are no more #ifdefs in board_init_r()
Signed-off-by: Simon Glass <[email protected]>
|
|
Use an accessor in the header file to avoid this.
Signed-off-by: Simon Glass <[email protected]>
|
|
There are copying errors in the help. Fix these.
Signed-off-by: Simon Glass <[email protected]>
|
|
Move the useful help to Kconfig.
Drop mention of CONFIG_SYS_MALLOC_SIMPLE since it doesn't exist.
Correct a 'CONFIGSYS_MALLOC_F_LEN' typo
Signed-off-by: Simon Glass <[email protected]>
|
|
Use CONFIG_SYS_MALLOC_F instead to of CONFIG_SYS_MALLOC_F_LEN to
determine whether pre-relocation malloc() is enabled.
Signed-off-by: Simon Glass <[email protected]>
|
|
Use the new SPL/TPL/VPL_SYS_MALLOC_F symbols to determine whether the
malloc pool exists.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Sean Anderson <[email protected]>
|
|
Enable CONFIG_TPL_SYS_MALLOC_F for boards which have a non-zero value
for CONFIG_TPL_SYS_MALLOC_F_LEN
Note that the default is yes in most cases, so no changes are needed to
board defconfig options.
Signed-off-by: Simon Glass <[email protected]>
|
|
Enable CONFIG_SPL_SYS_MALLOC_F for boards which have a non-zero value
for CONFIG_SPL_SYS_MALLOC_F_LEN
Note that the default is yes in most cases, so no changes are needed to
board defconfig options.
Signed-off-by: Simon Glass <[email protected]>
|
|
For U-Boot proper we have CONFIG_SYS_MALLOC_F which indicates that a
malloc() pool is available before relocation.
For SPL we only have CONFIG_SPL_SYS_MALLOC_F_LEN which indicates the
size of the pool.
In various places we use CONFIG_SPL_SYS_MALLOC_F_LEN == 0 to indicate
that there is no pool.
This differing approach is confusing. Add a new CONFIG_SPL_SYS_MALLOC_F
symbol for SPL (and similarly for TPL and VPL). Tidy up the Kconfig
help for clarity.
For now these symbols are not used. That is cleaned up in the following
patches.
Signed-off-by: Simon Glass <[email protected]>
|
|
These symbols do not (yet) exist, so drop the usage of them in the
serial Kconfig file. It has no effect.
Signed-off-by: Simon Glass <[email protected]>
|
|
This code is pretty ugly, with many #ifdefs
There are quite a lot of IH_OS_U_BOOT values so the compiler struggles
to create a jump table here. Also, most of the options are normally
disabled.
Change it to an else...if construct instead. Add an accessor for the
spl_image field behind an #ifdef to avoid needing #ifdef in the C code.
Signed-off-by: Simon Glass <[email protected]>
|
|
Move the condition to the header file to improve readability.
Signed-off-by: Simon Glass <[email protected]>
|
|
Avoid using the preprocessor for these checks.
Signed-off-by: Simon Glass <[email protected]>
|
|
It doesn't make sense to have some boards do this differently. Drop the
condition in the hope that the maintainers can figure out any run-time
problems.
This has been tested on qemu-ppce500
Signed-off-by: Simon Glass <[email protected]>
Acked-by: Christophe Leroy <[email protected]>
|
|
Use IF_ENABLED_INT() to avoid needing to use the preprocessor.
Signed-off-by: Simon Glass <[email protected]>
|
|
Rename this so that SPL is first, as per U-Boot convention. Also add
PAYLOAD_ since this is where in memory the parameters for the payload
have been stored.
Signed-off-by: Simon Glass <[email protected]>
|
|
We like to put the SPL first so it is clear that it relates to SPL. Rename
various malloc-related options which have crept in, to stick to this
convention.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Marcel Ziswiler <[email protected]>
Reviewed-by: Martyn Welch <[email protected]>
Reviewed-by: Svyatoslav Ryhel <[email protected]>
|
|
+ ae350: modify memory layout and target name
+ ae350: use generic RISC-V timer driver in S-mode
+ Support bootstage report for RISC-V
+ Support C extension exception command for RISC-V
+ Add Starfive timer support
|
|
- Resync some TI K3 DTS files, to fix booting on them.
|
|
moveconfig: enhance output; rename to qconfig
|
|
Sync k3-j721e DTS with kernel.org v6.6-rc1.
* Use mcu_timer0 defined in k3-j721e-mcu-wakeup.dtsi and remove
timer0, we have its clocks set up in clk-data now
* Remove hbmc node as support is buggy and needs to be fixed
* Remove aliases and chosen node, use them from Kernel
* Remove /delete-property/ and clock-frequency from sdhci,
usbss, and mcu_uart nodes as we have them in clk and dev data
* Remove dummy_clocks as they are not needed
* Remove cpsw node as it is not required since it has been fixed
in U-Boot
* Remove pcie nodes, they are not needed
* Remove mcu_i2c0 as it is used for tps659413 PMIC in j721e-sk
for which support is not yet added
* Change secproxy nodes to their Linux definitions
* Remove overriding of ti,cluster-mode in MAIN R5 to default to
lockstep mode same as Kernel
* Retain tps6594 node as TPS6594 PMIC support is still under
review in the Kernel [1], cleanup will be taken post its merge
[1] https://lore.kernel.org/all/[email protected]/
Signed-off-by: Neha Malcom Francis <[email protected]>
Reviewed-by: Manorit Chawdhry <[email protected]>
|
|
Get rid of k3-j721e-r5-*-u-boot.dtsi as it is not
necessary. Change the inclusion hierarchy to be as follows:
k3-j721e-<board>.dts---
-
-->k3-j721e-r5-<board>.dts
-
k3-j721e-<board>-u-boot.dtsi---
Reason for explicitly mentioning the inclusion of -u-boot.dtsi in code
although it could've been automatically done by U-Boot is to resolve
some of the dependencies that R5 file requires.
Also remove duplicate phandles while making this shift as well as remove
firmware-loader as it serves no purpose without "phandlepart" property.
Signed-off-by: Neha Malcom Francis <[email protected]>
|
|
Kernel commit d93036b47f35 ("arm64: dts: ti: k3-j721e-mcu_wakeup: Add
HyperBus node") was merged to kernel without its dependent patch [1].
Similar fix is needed in U-Boot, and hbmc currently breaks boot. Till
this gets fixed in U-Boot, disable the config by default so that the
hbmc probe that happens in board/ti/j721e/evm.c will not take place
and lead to boot failure.
[1] https://lore.kernel.org/all/[email protected]/
Signed-off-by: Neha Malcom Francis <[email protected]>
|
|
When setting up boot media to load the TIFS binary in legacy boot flow
(followed by J721E), get_timer() is called which calls dm_timer_init()
which then gets the tick-timer: mcu_timer0. mcu_timer0 uses k3_clks
(clock controller) and k3_pds (power controller) from the dmsc node that
forces probe of the ti_sci driver of TIFS that hasn't been loaded yet!
Running ti_sci_cmd_get_revision from the probe leads to panic since no
TIFS and board config binaries have been loaded yet. Resolve this by
moving ti_sci_cmd_get_revision to ti_sci_get_handle_from_sysfw as a
common point of invocation for both legacy and combined boot flows.
Before doing this, it is important to go through whether any sync points
exist where revision is needed before ti_sci_get_handle_from_sysfw is
invoked. Going through the code along with boot tests on both flows
ensures that there are none.
Signed-off-by: Neha Malcom Francis <[email protected]>
|
|
When setting boot media to load the TIFS binary in legacy boot flow
(followed by J721E), get_timer() is called which eventually calls
dm_timer_init() to grab the tick-timer, which is mcu_timer0. Since we
need to set up the clocks before using the timer, move clk_k3 driver
probe before k3_sysfw_loader to ensure we have all necessary clocks set
up before.
Signed-off-by: Neha Malcom Francis <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
Reviewed-by: Manorit Chawdhry <[email protected]>
|
|
U-Boot uses mcu_timer0 as the tick-timer, so add it to device list.
Signed-off-by: Neha Malcom Francis <[email protected]>
Reviewed-by: Manorit Chawdhry <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
|
|
Since commit [1] A53 u-boot proper is broken. This is because nodes
marked as 'bootph-pre-ram' are not available at u-boot proper before
relocation.
To fix this we mark all nodes in u-boot.dtsi as 'bootph-all'.
[1]
9e644284ab812 ("dm: core: Report bootph-pre-ram/sram node as pre-reloc after relocation")
Reported-by: Roger Quadros <[email protected]>
Signed-off-by: Nishanth Menon <[email protected]>
Reviewed-by: Roger Quadros <[email protected]>
|
|
CPSW node needs PHY, MDIO, pinmux, DMA and INTC nodes.
main_conf is required for phy_gmii_sel.
Mark them as 'bootph-all' so they are available in all
pre-relocation phases.
Fixes the below dts warnings:
<stdout>: Warning (reg_format): /bus@f0000/syscon@100000/phy@4044:reg: property has invalid length (8 bytes) (#address-cells == 2, #size-cells == 1)
<stdout>: Warning (reg_format): /bus@f0000/ethernet@8000000/ethernet-ports/port@1:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
<stdout>: Warning (unit_address_vs_reg): /bus@f0000/syscon@100000: node has a unit name, but no reg or ranges property
<stdout>: Warning (pci_device_reg): Failed prerequisite 'reg_format'
<stdout>: Warning (pci_device_bus_num): Failed prerequisite 'reg_format'
<stdout>: Warning (simple_bus_reg): Failed prerequisite 'reg_format'
<stdout>: Warning (i2c_bus_reg): Failed prerequisite 'reg_format'
<stdout>: Warning (spi_bus_reg): Failed prerequisite 'reg_format'
<stdout>: Warning (avoid_default_addr_size): /bus@f0000/syscon@100000/phy@4044: Relying on default #address-cells value
<stdout>: Warning (avoid_default_addr_size): /bus@f0000/syscon@100000/phy@4044: Relying on default #size-cells value
<stdout>: Warning (avoid_default_addr_size): /bus@f0000/ethernet@8000000/ethernet-ports/port@1: Relying on default #address-cells value
<stdout>: Warning (avoid_default_addr_size): /bus@f0000/ethernet@8000000/ethernet-ports/port@1: Relying on default #size-cells value
<stdout>: Warning (avoid_unnecessary_addr_size): Failed prerequisite 'avoid_default_addr_size'
<stdout>: Warning (unique_unit_address): Failed prerequisite 'avoid_default_addr_size'
Signed-off-by: Roger Quadros <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
|
|
Since commit [1] A53 u-boot proper is broken.
This is because nodes marked as 'bootph-pre-ram' are
not available at u-boot proper before relocation.
To fix this we mark all nodes in sk-u-boot.dtsi as
'bootph-all'.
[1]
9e644284ab812 ("dm: core: Report bootph-pre-ram/sram node as pre-reloc after relocation")
Signed-off-by: Roger Quadros <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
|
|
CPSW node needs PHY, MDIO, pinmux, DMA and INTC nodes.
Mark them as 'bootph-all' so they are available in all
pre-relocation phases.
Fixes below dts warnings:
<stdout>: Warning (reg_format): /bus@f4000/ethernet@8000000/mdio@f00/ethernet-phy@1:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
<stdout>: Warning (unit_address_vs_reg): /bus@f4000/ethernet@8000000/mdio@f00: node has a unit name, but no reg or ranges property
<stdout>: Warning (pci_device_reg): Failed prerequisite 'reg_format'
<stdout>: Warning (pci_device_bus_num): Failed prerequisite 'reg_format'
<stdout>: Warning (simple_bus_reg): Failed prerequisite 'reg_format'
<stdout>: Warning (i2c_bus_reg): Failed prerequisite 'reg_format'
<stdout>: Warning (spi_bus_reg): Failed prerequisite 'reg_format'
<stdout>: Warning (avoid_default_addr_size): /bus@f4000/ethernet@8000000/mdio@f00/ethernet-phy@1: Relying on default #address-cells value
<stdout>: Warning (avoid_default_addr_size): /bus@f4000/ethernet@8000000/mdio@f00/ethernet-phy@1: Relying on default #size-cells value
<stdout>: Warning (avoid_unnecessary_addr_size): Failed prerequisite 'avoid_default_addr_size'
<stdout>: Warning (unique_unit_address): Failed prerequisite 'avoid_default_addr_size'
<stdout>: Warning (msi_parent_property): /bus@f4000/bus@48000000/dma-controller@485c0100:msi-parent: Could not get phandle node for (cell 0)
<stdout>: Warning (msi_parent_property): /bus@f4000/bus@48000000/dma-controller@485c0000:msi-parent: Could not get phandle node for (cell 0)
<stdout>: Warning (phys_property): /bus@f4000/ethernet@8000000/ethernet-ports/port@2:phys: Could not get phandle node for (cell 0)
Signed-off-by: Roger Quadros <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
|
|
Since commit [1] A53 u-boot proper is broken.
This is because nodes marked as 'bootph-pre-ram' are
not available at u-boot proper before relocation.
To fix this we mark all nodes in sk-u-boot.dtsi as
'bootph-all'.
Move cbass_mcu node to -r5-sk.dts as it is only required
for R5 SPL.
[1]
9e644284ab812 ("dm: core: Report bootph-pre-ram/sram node as pre-reloc after relocation")
Signed-off-by: Roger Quadros <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
|
|
CPSW node needs PHY, MDIO, pinmux, DMA and INTC nodes.
USB and MMC nodes need pinmux.
Mark them as 'bootph-all' so they are available in all
pre-relocation phases.
Fixes below dts warning:
<stdout>: Warning (dmas_property): /bus@f4000/ethernet@8000000:dmas: Could not get phandle node for (cell 0)
Signed-off-by: Roger Quadros <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
|
|
Since commit [1] A53 u-boot proper is broken.
This is because nodes marked as 'bootph-pre-ram' are
not available at u-boot proper before relocation.
To fix this we mark all nodes in sk-u-boot.dtsi as
'bootph-all'.
Move vtt_supply and cbass_mcu node to -r5-evm.dts as
it is only required for R5 SPL.
[1]
9e644284ab812 ("dm: core: Report bootph-pre-ram/sram node as pre-reloc after relocation")
Signed-off-by: Roger Quadros <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
|
|
Update qconfig's documentation to better reflect its new purpose in life.
Signed-off-by: Simon Glass <[email protected]>
|
|
Use qconfig.db as the new name, to reflect the tool's purpose.
Signed-off-by: Simon Glass <[email protected]>
|
|
This does not move configs anymore, but queries them, based on a database
it can build. Rename the tool to better reflect its purpose.
Signed-off-by: Simon Glass <[email protected]>
|
|
Write the summary for -s and -b at the end, using a unified format.
Signed-off-by: Simon Glass <[email protected]>
|
|
Since moveconfig now just does what it is told (build database or sync
defconfigs) we don't need to print what it is doing. Drop this info, which
is of very little use.
Signed-off-by: Simon Glass <[email protected]>
|
|
Rather than printing all the failed boards, which are now easily visible
on the terminal, just show a summary. Sort it by defconfig and drop the
'_defconfig' suffix.
Signed-off-by: Simon Glass <[email protected]>
|
|
Show the number of accumulated failures when processing. Use a shorter
format with colour.
An unwanted space appears before the defconfig name on every item except
the last. Fix that while we are here.
Signed-off-by: Simon Glass <[email protected]>
|
|
Use the existing terminal code to handle ANSI colours. Enable colour by
default if the output is going to a terminal.
Signed-off-by: Simon Glass <[email protected]>
|
|
When the process is finished, moveconfig leaves a line saying that all
boards were processed (for better or worse). Drop this, since it is
unncessary.
Future work will provide a summary at the end instead.
Signed-off-by: Simon Glass <[email protected]>
|
|
Output a single line in the case where the defconfig only has one line
of output. Show the name without the _defconfig suffix, since that is the
same for all boards.
Use a list for the log so it is easier to process at the end.
Signed-off-by: Simon Glass <[email protected]>
|
|
There is no point in listing a board if everything went well. It makes it
harder to see the failures, particularly on a fast machine.
Suppress output unless something actually happened.
Drop the 'Syncing by savedefconfig' since this is selected by the -s and
is the same for all boards in this mode.
Signed-off-by: Simon Glass <[email protected]>
|
