summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2023-10-09arm64: zynqmp: Add support for vck190 revB system controllerMichal Simek
There are some changes between revA and revB boards. u39 8T49N240 was removed and also three ina226 at 42/43/44 addresses (u178/u180/u182). Signed-off-by: Michal Simek <[email protected]> Link: https://lore.kernel.org/r/461cfe5b2b882365413f90d19efd8abcd6be56ed.1695808407.git.michal.simek@amd.com
2023-10-09arm64: zynqmp: Remove xlnx,fclk nodesMichal Simek
xlnx,fclk nodes are not described in dtschema that's why remove them. Signed-off-by: Michal Simek <[email protected]> Link: https://lore.kernel.org/r/b25dedd066f587321751d7d20c1f65bb96c53b89.1695808407.git.michal.simek@amd.com
2023-10-09arm64: zynqmp: Add support for KD240 Kria SOM CCMichal Simek
Add support for KD240 Kria SOM CC. It is pretty much subset of KR260 board from PS perspective. Signed-off-by: Michal Simek <[email protected]> Link: https://lore.kernel.org/r/835f1d1b8982d46b902db69daad64e8445c051e9.1695808407.git.michal.simek@amd.com
2023-10-09arm64: zynqmp: Aligned QSPI configuration with latest specMichal Simek
Official DT binding description for dual stacked/paralllel configurations have been merged that's why switch to it. Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Michal Simek <[email protected]> Link: https://lore.kernel.org/r/2912091c231f5e945ee44601c285fe16263448da.1695378830.git.michal.simek@amd.com
2023-10-09ARM: zynq: Describe nand device in DTMichal Simek
Linux requires to describe nand structure under nand controller. If it is not described nand device is not detected by Linux. Error shown by Linux kernel: pl35x-nand-controller e1000000.nand-controller: Incorrect number of NAND chips (0) pl35x-nand-controller: probe of e1000000.nand-controller failed with error -22 When wired: nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda nand: Micron MT29F2G08ABAEAWP nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 Signed-off-by: Michal Simek <[email protected]> Link: https://lore.kernel.org/r/3fcd68ccdfed5e6c079681e3b29e06583ec8a375.1695378830.git.michal.simek@amd.com
2023-10-09arm64: zynqmp: Sync licenses with Linux kernelMichal Simek
There is difference between licenses in the Linux kernel and there shouldn't be any diff because all changes are coming from the same source at the same time. The difference is really in a time when they were upstreamed. That's why sync it up. Signed-off-by: Michal Simek <[email protected]> Link: https://lore.kernel.org/r/813b29378083153b67c60772f28cd2613519f338.1695378830.git.michal.simek@amd.com
2023-10-09arm64: zynqmp: Convert kv260-revA overlay to ASCII textMichal Simek
File was in UTF-8 format but there is no reason for it. Convert it to ASCII/plain text. Signed-off-by: Michal Simek <[email protected]> Link: https://lore.kernel.org/r/e4d52b898b461b86bb82009f37635f351279c753.1695378830.git.michal.simek@amd.com
2023-10-09arm64: dts: zynqmp: Add ports for the DisplayPort subsystemLaurent Pinchart
The DPSUB DT bindings now specify ports to model the connections with the programmable logic and the DisplayPort output. Add them to the device tree. Signed-off-by: Laurent Pinchart <[email protected]> Acked-by: Michal Simek <[email protected]> Signed-off-by: Michal Simek <[email protected]> Link: https://lore.kernel.org/r/1c91420e90bc823d7529834c33438216857c7161.1695378830.git.michal.simek@amd.com
2023-10-09arm64: dts: zynqmp: zcu106a: Describe DisplayPort connectorLaurent Pinchart
Add a device tree node to describe the DisplayPort connector, and connect it to the DPSUB output. Signed-off-by: Laurent Pinchart <[email protected]> Signed-off-by: Michal Simek <[email protected]> Link: https://lore.kernel.org/r/fe037c93ed41bc5ca97887964037520d449ca98c.1695378830.git.michal.simek@amd.com
2023-10-09arm64: xilinx: Remove address/size-cells from gem nodesMichal Simek
Some boards are using one mdio bus which holds multiple phys and also boards are using mdio node for bus description. That's why there are cases where address/size-cells are unnecessary which is also reported by make W=1 dtbs. That's why remove them from zynqmp.dtsi and let board DTSes to handle it based on used description. Error log: /axi/ethernet@ff0e0000: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property Signed-off-by: Michal Simek <[email protected]> Link: https://lore.kernel.org/r/02f308c774d4f2a798a9a8c066824114a19841a7.1695378830.git.michal.simek@amd.com
2023-10-09arm64: xilinx: Put ethernet phys to mdio nodeMichal Simek
All zynqmp boards have been already described via mdio node that's why also convert the rest of the boards. With using mdio node there is an option to add reset property for the whole mdio bus which is reflected by 's/phy-reset-gpios/reset-gpios/g' for some boards. Signed-off-by: Michal Simek <[email protected]> Link: https://lore.kernel.org/r/ff165281a70a38e2b76fee91e6255ce95ce8021b.1695378830.git.michal.simek@amd.com
2023-10-09arm64: zynqmp: Fix Siva's email address formatMichal Simek
Some patches didn't have his full name and also there was one more ">" at the end of email address. That's why correct both of these issues. Fixes: 174d728471d5 ("arm64: zynqmp: Switch to amd.com emails") Signed-off-by: Michal Simek <[email protected]> Link: https://lore.kernel.org/r/e970cc0dfabe293c2baf6b231d34f3af0386f1eb.1695378830.git.michal.simek@amd.com
2023-10-09arm64: zynqmp: Describe bus-width for SD card on KV260Michal Simek
SD card is connected with 4 data lines which should be described properly. Signed-off-by: Michal Simek <[email protected]> Link: https://lore.kernel.org/r/065cb9f1c6706eb4d70066e25cfc30d17b9f875d.1695378830.git.michal.simek@amd.com
2023-10-09arm64: xilinx: Use lower case for partition addressMichal Simek
Lower case should be used for register address. Issue is reported as: flash@0: partitions: Unevaluated properties are not allowed ('partition@22A0000' was unexpected) Signed-off-by: Michal Simek <[email protected]> Link: https://lore.kernel.org/r/66b3361df883ecab4f36ce3b4196fb606c802598.1695378830.git.michal.simek@amd.com
2023-10-09arm64: xilinx: Remove address/size-cells from flash nodeMichal Simek
Partitions are described via fixed-partitions that's why there is no need to have address/size-cells in flash node. Signed-off-by: Michal Simek <[email protected]> Link: https://lore.kernel.org/r/c704be9d9f3d09c1cc55b092efeb9c73fcda6451.1695378830.git.michal.simek@amd.com
2023-10-09arm64: dts: xilinx: zynqmp: Add RPU subsystem device nodeTanmay Shah
RPU subsystem can be configured in cluster-mode or split mode. Also each r5 core has separate power domains. Signed-off-by: Tanmay Shah <[email protected]> Signed-off-by: Michal Simek <[email protected]> Link: https://lore.kernel.org/r/dde364939b4fbe3f7be7b6f5dff42e7d8b2f5c46.1695378830.git.michal.simek@amd.com
2023-10-09arm64: zynqmp: Describe interrupts by using macrosMichal Simek
Use arm-gic.h and irq.h for interrupt description. It helps to improve readability of device tree file. Suggested-by: Laurent Pinchart <[email protected]> Signed-off-by: Michal Simek <[email protected]> Link: https://lore.kernel.org/r/e0db567e1eb4e4e90e59270f41708919682dacf4.1695378830.git.michal.simek@amd.com
2023-10-09arm64: zynqmp: Remove resetin/out from K24 psu_initMichal Simek
The code is not called that's why remove it. Signed-off-by: Michal Simek <[email protected]> Link: https://lore.kernel.org/r/7b207e90f68028ab36fcc22df4127492f174793d.1695046281.git.michal.simek@amd.com
2023-10-09arm64: zynqmp: Rename dt overlay file names from dts to dtsoMichal Simek
Use dtso suffix instead of dts. Build option was introduced by commit a0f9a77912b2 ("kbuild: Allow DTB overlays to built from .dtso named source files"). Signed-off-by: Michal Simek <[email protected]> Link: https://lore.kernel.org/r/1dce37e72428c14a3ccbb5dc674b90dfe56b75ac.1695046155.git.michal.simek@amd.com
2023-10-09arm64: zynqmp: Describe assigned-clocks for uartsMichal Simek
Describe assigned-clocks for both uarts. SOM is using this functionality. Signed-off-by: Michal Simek <[email protected]> Link: https://lore.kernel.org/r/bddbb81209a4567b0939c5d2d0ecb42fdfcd71ea.1695036114.git.michal.simek@amd.com
2023-10-09pinctrl: zynqmp: Display the tristate configuration for all pinsVenkatesh Yadav Abbarapu
Read the tristate config for all the pins and display it. ZynqMP> pinmux status MIO1 MIO1: slew:fast bias:enabled pull:up input:cmos drive:12mA volt:1.8 tri_state:enabled Signed-off-by: Venkatesh Yadav Abbarapu <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Michal Simek <[email protected]>
2023-10-09pinctrl: Increase size of pinmux status bufferVenkatesh Yadav Abbarapu
For Xilinx ZynqMP SOC new parameter was added and now it can set 7 parameters for its pins. Pinmux status command will print the status of these parameters for each pin. But current print buffer length is only 80 characters long, increase it to 90 to print all the parameters without truncation. Signed-off-by: Venkatesh Yadav Abbarapu <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Michal Simek <[email protected]>
2023-10-09net: zynq_gem: Update the MDC clock divisor in the probe functionVenkatesh Yadav Abbarapu
MDC clock change needs to be done when the driver probe function is called as mdio is enabled at probe and not when the ethernet starts. Setup the MDC clock at the probe itself. Signed-off-by: Venkatesh Yadav Abbarapu <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Michal Simek <[email protected]>
2023-10-08Merge tag 'u-boot-rockchip-20231007' of ↵Tom Rini
https://source.denx.de/u-boot/custodians/u-boot-rockchip - Add Board: rk3568 Bananapi R2Pro; - Update pcie bifurcation support; - dwc_eth_qos controller support for rk3568 and rk3588; - Compressed binary support for U-Boot on rockchip platform; - dts and config updates for different board and soc; [ trini: Fix conflict on include/spl.h ] Signed-off-by: Tom Rini <[email protected]>
2023-10-07rockchip: rk356x-u-boot: Add bootph-all to i2c0_xfer pinctrl nodeJonas Karlman
A RK8XX PMIC is typically using i2c0 on RK356x devices. Add bootph-all to required pinctrl nodes to simplify use of the prevent booting on power plug-in option in SPL. With the following Kconfig options and nodes in u-boot.dtsi the prevent booting on power plug-in option can work in SPL. CONFIG_ROCKCHIP_RK8XX_DISABLE_BOOT_ON_POWERON=y CONFIG_SPL_I2C=y CONFIG_SPL_POWER=y CONFIG_SPL_PINCTRL=y CONFIG_SPL_PMIC_RK8XX=y &i2c0 { bootph-pre-ram; }; &rk817 { bootph-pre-ram; regulators { bootph-pre-ram; }; }; Signed-off-by: Jonas Karlman <[email protected]> Reviewed-by: Kever Yang <[email protected]>
2023-10-07power: pmic: rk8xx: Fix power-on source check in SPLJonas Karlman
The commit 30975fb73d51 ("rockchip: Add option to prevent booting on power plug-in") introduce an option to prevent booting a device when the device was powered on due to power plug-in instead of pressing a power button. This feature works by checking the power-on source during PMIC probe and powers off the device if power-on source was power plug-in. This check currently runs very late at PMIC probe in U-Boot proper. Fix so that the power-on source check can work at probe time in SPL. Also enable probe after bind and remove the PMIC banner in SPL. With this we can use ROCKCHIP_RK8XX_DISABLE_BOOT_ON_POWERON and SPL_PMIC_RK8XX to power off the device very quickly after TPL instead of after TF-A and U-Boot proper has been loaded and run. DDR V1.18 f366f69a7d typ 23/07/17-15:48:58 ln LP4/4x derate en, other dram:1x trefi ddrconfig:7 LPDDR4X, 324MHz BW=32 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=16 Size=8192MB change to: 324MHz clk skew:0x64 change to: 528MHz clk skew:0x58 change to: 780MHz clk skew:0x58 change to: 1056MHz(final freq) clk skew:0x40 out Power Off due to plug-in event Fixes: 30975fb73d51 ("rockchip: Add option to prevent booting on power plug-in") Signed-off-by: Jonas Karlman <[email protected]>
2023-10-07rockchip: rk356x: Enable poweroff commandJonas Karlman
With PMIC_RK8XX, SYSRESET and CMD_POWEROFF options enabled it is possible to power down a board using the poweroff command and turn the board back on using a power button. Enable the poweroff command on RK356x boards that have a button wired to PMIC pwron. Signed-off-by: Jonas Karlman <[email protected]> Reviewed-by: Simon Glass <[email protected]> Reviewed-by: Kever Yang <[email protected]>
2023-10-07power: pmic: rk8xx: Use sysreset implementation of the poweroff commandJonas Karlman
Select SYSRESET_CMD_POWEROFF to use the sysreset implementation of the poweroff command when PMIC_RK8XX is enabled. Signed-off-by: Jonas Karlman <[email protected]> Reviewed-by: Simon Glass <[email protected]> Reviewed-by: Kever Yang <[email protected]>
2023-10-07configs: rockchip: rk3308: enable CONFIG_OF_LIBFDT_OVERLAYFUKAUMI Naoki
enable CONFIG_OF_LIBFDT_OVERLAY and use it on Radxa ROCK Pi S. Signed-off-by: FUKAUMI Naoki <[email protected]>
2023-10-07configs: rockchip: rk3308: use CONFIG_DEFAULT_FDT_FILEFUKAUMI Naoki
all rk3308 boards should use their own dtb file. also, change fdt_addr_r to avoid following error: "ERROR: Did not find a cmdline Flattened Device Tree" it happens on Radxa ROCK Pi S (256MB/512MB) with kernel built from Radxa BSP. Signed-off-by: FUKAUMI Naoki <[email protected]>
2023-10-07arm: dts: rockchip: rock-5b: add support for PCIe3 and NVMeFUKAUMI Naoki
this patch adds support for PCIe3 (M.2 M key) and enables NVMe. => pci BusDevFun VendorId DeviceId Device Class Sub-Class _____________________________________________________________ 00.00.00 0x1d87 0x3588 Bridge device 0x04 01.00.00 0x10ec 0x8125 Network controller 0x00 02.00.00 0x1d87 0x3588 Bridge device 0x04 03.00.00 0x1179 0x011a Mass storage controller 0x08 => nvme scan => nvme info Device 0: Vendor: 0x1179 Rev: AGHA4101 Prod: 79CA20WPKRYN Type: Hard Disk Capacity: 488386.3 MB = 476.9 GB (1000215216 x 512) Signed-off-by: FUKAUMI Naoki <[email protected]> Reviewed-by: Kever Yang <[email protected]>
2023-10-07arm: dts: rockchip: sync DT for RK3588 series with LinuxFUKAUMI Naoki
Sync the device tree for RK3588 series with Linux 6.6-rc1. Signed-off-by: FUKAUMI Naoki <[email protected]> Reviewed-by: Kever Yang <[email protected]>
2023-10-07configs: rockchip: rock-pi-s: use default bootdelay (2s)FUKAUMI Naoki
align with other boards. Signed-off-by: FUKAUMI Naoki <[email protected]> Reviewed-by: Kever Yang <[email protected]>
2023-10-07configs: rockchip: add DOS_PARTITION to RK3308 boards defconfigMassimo Pegorer
Without DOS_PARTITION support U-Boot is not able to boot an OS stored into an SD card with MBR partitions table. This is still a quite common case so add DOS_PARTITION (only for U-Boot proper build) to Rockchip RK3308 EVB, Radxa ROCK Pi S and Firefly roc-rk3308-cc boards: they are the only RK boards missing of DOS_PARTITION. Reported-by: Jayantajit Gogoi <[email protected]> Signed-off-by: Massimo Pegorer <[email protected]> Reviewed-by: Kever Yang <[email protected]>
2023-10-07board: rockchip: Add Bananapi R2Pro BoardFrank Wunderlich
Add Bananapi R2 Pro board. tested: - sdcard - both front usb-ports - sata - wan-port lan-ports are connected to mt7531 switch where driver needs to be separated from mtk ethernet-driver. Signed-off-by: Frank Wunderlich <[email protected]> Reviewed-by: Kever Yang <[email protected]> Reviewed-by: Jonas Karlman <[email protected]>
2023-10-07configs: rockchip: Enable ethernet driver on RK3588 boardsJonas Karlman
Enable DWC_ETH_QOS_ROCKCHIP and related PHY driver on RK3588 boards that have an enabled gmac node and drop ETH_DESIGNWARE and GMAC_ROCKCHIP for remaining RK3588 boards. Signed-off-by: Jonas Karlman <[email protected]> Reviewed-by: Kever Yang <[email protected]>
2023-10-07configs: rockchip: Enable ethernet driver on RK356x boardsJonas Karlman
Enable DWC_ETH_QOS_ROCKCHIP and related PHY driver on RK356x boards that have an enabled gmac node. Signed-off-by: Jonas Karlman <[email protected]> Reviewed-by: Kever Yang <[email protected]>
2023-10-07net: dwc_eth_qos_rockchip: Add support for RK3588Jonas Karlman
Add rk_gmac_ops and other special handling that is needed for GMAC to work on RK3588. rk_gmac_ops was ported from linux commits: 2f2b60a0ec28 ("net: ethernet: stmmac: dwmac-rk: Add gmac support for rk3588") 88619e77b33d ("net: stmmac: rk3588: Allow multiple gmac controller") Signed-off-by: Jonas Karlman <[email protected]> Reviewed-by: Kever Yang <[email protected]> Reviewed-by: Sebastian Reichel <[email protected]> Reviewed-by: Ramon Fried <[email protected]>
2023-10-07net: dwc_eth_qos: Add glue driver for GMAC on Rockchip RK3568Jonas Karlman
Add a new glue driver for Rockchip SoCs, i.e RK3568, with a GMAC based on Synopsys DWC Ethernet QoS IP. rk_gmac_ops was ported from linux commit: 3bb3d6b1c195 ("net: stmmac: Add RK3566/RK3568 SoC support") Signed-off-by: Jonas Karlman <[email protected]> Reviewed-by: Kever Yang <[email protected]> Reviewed-by: Ramon Fried <[email protected]>
2023-10-07net: dwc_eth_qos: Stop spam of RX packet not available messageJonas Karlman
Remove spam of RX packet not available debug messages when waiting to receive a packet. Signed-off-by: Jonas Karlman <[email protected]> Reviewed-by: Kever Yang <[email protected]> Reviewed-by: Ramon Fried <[email protected]>
2023-10-07net: dwc_eth_qos: Return error code when start failsJonas Karlman
Return error code when phy_connect fails or no link can be established. Signed-off-by: Jonas Karlman <[email protected]> Reviewed-by: Kever Yang <[email protected]> Reviewed-by: Ramon Fried <[email protected]>
2023-10-07net: dwc_eth_qos: Drop unused rx_pkt from eqos_privJonas Karlman
rx_pkt is allocated and not used for anything, remove it. Signed-off-by: Jonas Karlman <[email protected]> Reviewed-by: Kever Yang <[email protected]> Reviewed-by: Ramon Fried <[email protected]>
2023-10-07rockchip: Add support to generate LZMA compressed U-boot binaryManoj Sai
Add support for generating a LZMA-compressed U-boot binary with the help of binman, if CONFIG_SPL_LZMA is selected. Signed-off-by: Manoj Sai <[email protected]> Reviewed-by: Simon Glass <[email protected]> Reviewed-by: Kever Yang <[email protected]>
2023-10-07rockchip: Add support to generate GZIP compressed U-boot binaryManoj Sai
Add support for generating a GZIP-compressed U-boot binary with the help of binman, if CONFIG_SPL_GZIP is selected. Signed-off-by: Manoj Sai <[email protected]> Reviewed-by: Simon Glass <[email protected]> Reviewed-by: Kever Yang <[email protected]>
2023-10-07spl: fit: support for booting a LZMA-compressed U-boot binaryManoj Sai
If LZMA Compression support is enabled, LZMA compressed U-Boot binary will be placed at a specified RAM location which is defined at CONFIG_SYS_LOAD_ADDR and will be assigned as the source address. image_decomp() function, will decompress the LZMA compressed U-Boot binary which is placed at source address(CONFIG_SYS_LOAD_ADDR) to the default CONFIG_SYS_TEXT_BASE location. spl_load_fit_image function will load the decompressed U-Boot binary, which is placed at the CONFIG_SYS_TEXT_BASE location. Signed-off-by: Manoj Sai <[email protected]> Signed-off-by: Suniel Mahesh <[email protected]> Reviewed-by: Simon Glass <[email protected]> Reviewed-by: Kever Yang <[email protected]> Reviewed-by: Tom Rini <[email protected]>
2023-10-07spl: fit: support for booting a GZIP-compressed U-boot binaryManoj Sai
If GZIP Compression support is enabled, GZIP compressed U-Boot binary will be at a specified RAM location which is defined at CONFIG_SYS_LOAD_ADDR and will be assign it as the source address. gunzip function in spl_load_fit_image ,will decompress the GZIP compressed U-Boot binary which is placed at source address(CONFIG_SYS_LOAD_ADDR) to the default CONFIG_SYS_TEXT_BASE location. spl_load_fit_image function will load the decompressed U-Boot binary, which is placed at the CONFIG_SYS_TEXT_BASE location. Signed-off-by: Manoj Sai <[email protected]> Signed-off-by: Suniel Mahesh <[email protected]> Reviewed-by: Kever Yang <[email protected]> Reviewed-by: Simon Glass <[email protected]> Reviewed-by: Tom Rini <[email protected]>
2023-10-07doc: rockchip: Update and improve info on rk3308, TPL and TF-AMassimo Pegorer
Update and improve documentation about build steps for SoCs that require using TF-A and TPL binaries provided by Rockchip, such as rk3308. Add rk3308 boards case to rST document. Add ROCK Pi S in the list of supported boards. Minor page format improvements. Signed-off-by: Massimo Pegorer <[email protected]> Reviewed-by: Kever Yang <[email protected]>
2023-10-07rockchip: Kconfig: Enable external TPL binary for rk3308Massimo Pegorer
There is no support to initialize DRAM on rk3308 SoC using U-Boot TPL or SPL, and therefore an external TPL binary must be used to package a bootable u-boot-rockchip.bin image. Default ROCKCHIP_EXTERNAL_TPL to yes if ROCKCHIP_RK3308. Remove useless TPL_SERIAL. Signed-off-by: Massimo Pegorer <[email protected]> Tested-by: FUKAUMI Naoki <[email protected]> Reviewed-by: Kever Yang <[email protected]>
2023-10-07rockchip: board: Add minimal generic RK3566/RK3568 boardJonas Karlman
Add a minimal generic RK3566/RK3568 board that only have eMMC and SDMMC enabled. This defconfig can be used to boot from eMMC or SD-card on most RK3566/RK3568 boards that follow reference board design. Signed-off-by: Jonas Karlman <[email protected]> Reviewed-by: Kever Yang <[email protected]>
2023-10-07rockchip: Port IO-domain driver for RK3568 from linuxJonas Karlman
Port the Rockchip IO-domain driver for RK3568 from linux. The driver auto probe after bind to configure IO-domain based on the regulator voltage. Compared to the linux driver this driver is not notified about regulator voltage changes and only configure IO-domain based on the initial voltage autoset by the regulator. It is not recommended to enable MMC_IO_VOLTAGE or the mmc signal voltage and IO-domain may end up out of sync. Based on the linux commit 28b05a64e47c ("soc: rockchip: io-domain: add rk3568 support"). Signed-off-by: Jonas Karlman <[email protected]> Reviewed-by: Simon Glass <[email protected]> Reviewed-by: Kever Yang <[email protected]>
generated by cgit v1.3.1 (git 2.54.0) at 2026-09-01 12:14:23 +0000