| Age | Commit message (Collapse) | Author |
|---|
|
Introduce reboot, boot and continue commands support to
TCP fastboot by moving existing UDP logic into the common module.
Signed-off-by: Dmitrii Merkurev <[email protected]>
Cc: Ying-Chun Liu (PaulLiu) <[email protected]>
Cc: Simon Glass <[email protected]>
Сс: Joe Hershberger <[email protected]>
Сс: Ramon Fried <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Known limitations are
1. fastboot reboot doesn't work (answering OK but not rebooting)
2. flashing isn't supported (TCP transport only limitation)
The command syntax is
fastboot tcp
Signed-off-by: Dmitrii Merkurev <[email protected]>
Cc: Ying-Chun Liu (PaulLiu) <[email protected]>
Cc: Simon Glass <[email protected]>
Сс: Joe Hershberger <[email protected]>
Сс: Ramon Fried <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Make following changes to unblock TCP fastboot support:
1. Implement being a TCP server support
2. Introduce dedicated TCP traffic handler (get rid of UDP signature)
3. Ensure seq_num and ack_num are respected in net_send_tcp_packet
function (make sure existing wget_cmd code is reflected with the fix)
Signed-off-by: Dmitrii Merkurev <[email protected]>
Cc: Ying-Chun Liu (PaulLiu) <[email protected]>
Cc: Simon Glass <[email protected]>
Сс: Joe Hershberger <[email protected]>
Сс: Ramon Fried <[email protected]>
Reviewed-by: Ying-Chun Liu (PaulLiu) <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
|
|
Requires proper environment with DHCP6 server provisioned.
Signed-off-by: Sean Edmond <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
|
|
Adds commands to support DHCP and PXE with IPv6.
New configs added:
- CMD_DHCP6
- DHCP6_PXE_CLIENTARCH
- DHCP6_PXE_DHCP_OPTION
- DHCP6_ENTERPRISE_ID
New commands added (when IPv6 is enabled):
- dhcp6
- pxe get -ipv6
- pxe boot -ipv6
Signed-off-by: Sean Edmond <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
|
|
Adds DHCPv6 protocol to u-boot.
Allows for address assignement with DHCPv6 4-message exchange
(SOLICIT->ADVERTISE->REQUEST->REPLY). Includes DHCPv6 options
required by RFC 8415. Also adds DHCPv6 options required
for PXE boot.
Possible enhancements:
- Duplicate address detection on DHCPv6 assigned address
- IPv6 address assignement through SLAAC
- Sending/parsing other DHCPv6 options (NTP, DNS, etc...)
Signed-off-by: Sean Edmond <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
|
|
rtl8211e_startup() is an exact copy of genphy_startup(). Use that
instead of duplicating it.
Signed-off-by: Rasmus Villemoes <[email protected]>
|
|
Functionally, bcm_cygnus_startup() is an exact copy of
genphy_startup().
Signed-off-by: Rasmus Villemoes <[email protected]>
|
|
Read the phy mode of the external phy from the device tree if available
and check that it is a RGMII variant.
Signed-off-by: Stefan Herbrechtsmeier <[email protected]>
|
|
NFSv1 support added by Christian Gmeiner, Thomas Rienoessl,
September 27, 2018. As of now, NFSv3 is the default choice.
if the server does not support NFSv3, we fall back to
versions 2 or 1.
Signed-off-by: Thomas RIENOESSL <[email protected]>
|
|
Signed-off-by: Thomas RIENOESSL <[email protected]>
|
|
Signed-off-by: Thomas RIENOESSL <[email protected]>
|
|
Prep. work to support nfs v1.
Signed-off-by: Thomas RIENOESSL <[email protected]>
|
|
Without that patch it lost track to the node to scan
speed and duplex.
Patch was created by Marek Vasut, just tested by me.
Signed-off-by: Elmar Psilog <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
Fix "setenv gatewayip6".
Synchronize IPv6 local variables with environment variables
in netboot_update_env()
Signed-off-by: Sean Edmond <[email protected]>
|
|
In the process of adopting CONFIG_DM_ETH on the DPAA2 based platforms,
interfaces which were previously defined as "xgmii" were transitioned to
be defined as "xfi" in the DTS.
See the commit below for reference:
commit 87274918f2f4 ("arm: dts: ls2088ardb: add DPMAC and PHY nodes")
Then Vladimir's commit replaced all occurrences of "xfi" with
"10gbase-r" in an effort to make U-Boot work with the same device tree
as Linux.
commit 77b11f760416 ("net: replace the "xfi" phy-mode with "10gbase-r"")
These changes to the phy_interface_t of an Ethernet port meant that the
mc_fixup_mac_addrs() function was no longer capable to properly fixup
the MAC addresses. The problem arises from the fact that the hardcoded
information about an interface (wriop_get_enet_if()) was no longer
matching any actual device.
For example, the function tried to search for "DPMAC1@xgmii1" by name
using eth_get_dev_by_name() when only "DPMAC1@10gbase-r" was available.
This function removes the need to rely on the hardcoded information by
iterating through all the UCLASS_ETH devices which are DPAA2 and request
a fixup for each of them.
Signed-off-by: Ioana Ciornei <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
|
|
Export the ldpaa_eth_get_dpmac_id() function so that it can be used from
other drivers, especially by fsl-mc which will need it the next patch.
Also, create a macro for the Ethernet ldpaa driver name and export it as
well.
Signed-off-by: Ioana Ciornei <[email protected]>
|
|
Add a port_probe function to configure the phy. This leads to
earlier link negotiation so the port is more likely to be ready
when used.
Signed-off-by: Tim Harvey <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
|
|
We don't do anything useful with the master dev, so remove the variable.
Signed-off-by: Tim Harvey <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
|
|
packet tagging is not used for this driver so we do not need to
call dsa_set_tagging.
Signed-off-by: Tim Harvey <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-video
- enable video support in SPL
- support splash screen for TI am62x
- replace #ifdef and #if with if's in bmp/splash
- add lm3533 backlight driver
- add Solomon SSD2825 DSI/LVDS bridge driver
- add Renesas R61307 and R69328 MIPI DSI panel drivers
- add tegra DC based PWM backlight driver
- add generic endeavoru (HTC One X) panel driver
|
|
https://source.denx.de/u-boot/custodians/u-boot-fsl-qoriq
fsl-ls1088a device tree update
enable DM_SERIAL for ten64
check for crypto node first in fdt_fixup_remove_jr
|
|
When CMPC885 board is used for MIAE device, SCC2 SCC3 and SMC2
are used for serial lines. Therefore only SCC4 is available for
handling the TDM line.
In order to use SCC4 in QMC mode without loosing SMC2, SMC2
must be relocated.
Activate SMC relocation and relocate SMC2 at offset 0x1fc0 which
is unused.
Signed-off-by: Christophe Leroy <[email protected]>
|
|
Instead of inhibiting parameter RAM relacation, take
into account the configured one.
It means INIT_TRX command cannot be used and must be done
manually as explained in the microcode patch application note.
Signed-off-by: Christophe Leroy <[email protected]>
|
|
Instead of inhibiting parameter RAM relocation, take it into account.
Signed-off-by: Christophe Leroy <[email protected]>
|
|
In order to use QMC mode in the CPM, a SCC requires more space
in parameter RAM.
After SCC1 there is I2C parameter RAM and after SCC2 there is
SPI parameter RAM. MPC866 and MPC885 can already relocate I2C and.
SPI parameter RAM.
But in order to free space after SCC3 and SCC4, SMC1 and SMC2
need to be relocated. In order to do so, a CPM microcode patch
is required.
Binary data for that patch is copied from Linux kernel.
Signed-off-by: Christophe Leroy <[email protected]>
|
|
MPC885 CPU has the following ERRATA:
When the USB controller is configured in Host mode, and the
SOF generation (SFTE=1 in USMOD register) is being used,
there may be false CRC error indication in other SCCs.
Although the data is received correctly, the CRC result
will be corrupted.
Add capability to load the related microcode to fix it.
The microcode binary data is copied from Linux kernel.
Other microcode will be added in following patch so make it
a Kconfig choice.
Signed-off-by: Christophe Leroy <[email protected]>
|
|
sparse reports the following warning:
CHECK arch/powerpc/cpu/mpc8xx/micropatch_usb_sof.c
arch/powerpc/cpu/mpc8xx/micropatch_usb_sof.c:29:9: warning: cast removes address space '<asn:2>' of expression
arch/powerpc/cpu/mpc8xx/micropatch_usb_sof.c:30:9: warning: cast removes address space '<asn:2>' of expression
This is because of (void *) casts for using memcpy() as a substitute.
Do like other architectures, __force the cast to silence the warning
Signed-off-by: Christophe Leroy <[email protected]>
|
|
Somehow, I managed to typo our company name in the U-Boot
and Linux kernel submissions.
Fix this and update the copyright year at the same time.
Signed-off-by: Mathew McBride <[email protected]>
Acked-by: Peng Fan <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
Reviewed-by: Ioana Ciornei <[email protected]>
Tested-by: Ioana Ciornei <[email protected]> # on LS1088A-RDB
|
|
This synchronises the Linux device tree with U-Boot
(cp linux/..../fsl-ls1088a-ten64.dts uboot/..../fsl-ls1088a-ten64.dts),
as of Linux v6.2-rc5.
Missing from the U-Boot copy previously was the
Ethernet PCS definitions (required for linking with PHY in
Linux but not used by U-Boot) and various upstream
fixes and formatting changes.
The board microcontroller (which doesn't have a Linux driver)
has been moved to the -u-boot.dtsi, as well as the
spi0 quadspi alias (used by U-boot 'sf' but not valid for Linux).
Signed-off-by: Mathew McBride <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
Reviewed-by: Ioana Ciornei <[email protected]>
Tested-by: Ioana Ciornei <[email protected]> # on LS1088A-RDB
|
|
This is effectively:
cp linux/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi \
u-boot/arch/arm/dts/fsl-ls1088a.dtsi
Tested working with Ten64 board (LS1088A) booting openSUSE Tumbleweed.
Signed-off-by: Mathew McBride <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
Reviewed-by: Ioana Ciornei <[email protected]>
Tested-by: Ioana Ciornei <[email protected]> # on LS1088A-RDB
|
|
Our [U-Boot] copy of fsl-ls1088a.dtsi had all the hardware under
the top level, until the DM_SERIAL implementation recently.
In this commit, remove any remaining devices (that were in U-Boot,
but not touched by previous patches in this series) to be under /soc,
updating to their upstream (Linux) bindings.
The bindings have been copied closest to their relative positions
in the Linux version, so the eventual result is that the U-Boot
and Linux fsl-ls1088a.dtsi will be identical.
The next commit will add the hardware bindings that were not
in U-Boot.
Signed-off-by: Mathew McBride <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
Reviewed-by: Ioana Ciornei <[email protected]>
Tested-by: Ioana Ciornei <[email protected]> # on LS1088A-RDB
|
|
This moves the fsl-mc device tree definition under the /soc
node, as well as adding interrupt and IOMMU definitions that
were not in U-Boot before.
There are slight differences between the two bindings
as we add a "simple-mfd" compatible to function
under U-Boot's driver model.
Signed-off-by: Mathew McBride <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
Reviewed-by: Ioana Ciornei <[email protected]>
Tested-by: Ioana Ciornei <[email protected]> # on LS1088A-RDB
|
|
Synchronise the MDIO controller definitions with Linux, so
the controllers will be usable when passing U-Boot's
control FDT to Linux.
This also adds the PCS (internal controller) definitions
which are not used by U-Boot.
Caveat: The kernel definition uses "fsl,fman-memac-mdio",
as with other members of the Layerscape family, but
U-Boot uses a different driver for the DPAA2
Family devices (LS1088/LS2088/LX2160). So
we use "fsl,ls-mdio" as the first compatible string
for these devices.
Signed-off-by: Mathew McBride <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
Reviewed-by: Ioana Ciornei <[email protected]>
Tested-by: Ioana Ciornei <[email protected]> # on LS1088A-RDB
|
|
Synchronise the USB device tree definition with Linux, allowing
the U-Boot control FDT to be used to boot a Linux system with
working USB.
An extra compatible string, "fsl,layerscape-dwc3" is needed
for special handling in U-Boot, so has been added to the
-u-boot.dtsi file. It might be better to add this to the
Linux source bindings.
Signed-off-by: Mathew McBride <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
Reviewed-by: Ioana Ciornei <[email protected]>
Tested-by: Ioana Ciornei <[email protected]> # on LS1088A-RDB
|
|
U-Boot's definition for the I2C controllers did not contain any
clock information. This resulted in the I2C not functioning when
the U-Boot control FDT was passed to Linux.
Signed-off-by: Mathew McBride <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
Reviewed-by: Ioana Ciornei <[email protected]>
Tested-by: Ioana Ciornei <[email protected]> # on LS1088A-RDB
|
|
Move the GPIO controller definitions under the "soc" and in
the same relative position as the Linux kernel fsl-ls1088a.dtsi.
Signed-off-by: Mathew McBride <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
Reviewed-by: Ioana Ciornei <[email protected]>
Tested-by: Ioana Ciornei <[email protected]> # on LS1088A-RDB
|
|
This is required for Linux to boot using the same FDT as
U-Boot (such as passing the control FDT to bootefi).
Signed-off-by: Mathew McBride <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
Reviewed-by: Ioana Ciornei <[email protected]>
Tested-by: Ioana Ciornei <[email protected]> # on LS1088A-RDB
|
|
The Linux kernel fsl-ls1088a.dtsi disables (status="disabled")
all PCIe controllers by default, with the bootloader (i.e U-Boot)
enabling the appropriate controllers (specified by the board
reset control word/RCW) by FDT fixup.
However, U-Boot needs these controllers to be enabled
to be usable, which we can add in the u-boot only dtsi.
Signed-off-by: Mathew McBride <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
Reviewed-by: Ioana Ciornei <[email protected]>
Tested-by: Ioana Ciornei <[email protected]> # on LS1088A-RDB
|
|
This moves the PCIe controller definitions under /soc and adopts
the same bindings (fsl,ls1088a-pcie) as Linux. Previously,
the format was different between the two versions.
Signed-off-by: Mathew McBride <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
Reviewed-by: Ioana Ciornei <[email protected]>
Tested-by: Ioana Ciornei <[email protected]> # on LS1088A-RDB
|
|
To synchronise the device tree in U-Boot with Linux, the GIC
(Interrupt Controller) and SMMU/IOMMU nodes need to be synchronised
before changing any dependent components like PCIe and DPAA2/fsl-mc.
Signed-off-by: Mathew McBride <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
Reviewed-by: Ioana Ciornei <[email protected]>
Tested-by: Ioana Ciornei <[email protected]> # on LS1088A-RDB
|
|
This allows the Layerscape PCIe RC driver to use the upstream
style binding (two "reg" entries instead of four).
It is similar to the previous commit e10da1f985ad
("pci: layerscape: add official ls1028a binding support")
which implemented this for the LS1028A.
Signed-off-by: Mathew McBride <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
Reviewed-by: Ioana Ciornei <[email protected]>
Tested-by: Ioana Ciornei <[email protected]> # on LS1088A-RDB
|
|
The top-level "memory" node does not exist in the Linux
version of the fsl-ls1088a.dtsi file. Move it to the U-Boot
"tweak" file, so we can have an identical copy of
fsl-ls1088a.dtsi between the projects in the end.
Signed-off-by: Mathew McBride <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
Reviewed-by: Ioana Ciornei <[email protected]>
Tested-by: Ioana Ciornei <[email protected]> # on LS1088A-RDB
|
|
This moves the bootph-all tags that were added in commit a593c1fec579
("arch: arm: dts: fsl-ls1088a.dtsi: tag serial nodes with bootph-all")
into a u-boot only include.
Due to the way the U-Boot device tree "tweak" system is setup[1],
we need to have a per-board <boardname>-u-boot.dtsi, which will
include the "fsl-ls1088a-u-boot.dtsi" tweaks.
By doing so, future updates to fsl-ls1088a.dtsi from upstream
(Linux kernel) can just be copied directly into the U-Boot tree,
without worrying about any extra data local to U-Boot.
Signed-off-by: Mathew McBride <[email protected]>
[1] - https://u-boot.readthedocs.io/en/latest/develop/devicetree/control.html#adding-tweaks-for-u-boot
The CONFIG_SYS_SOC, CONFIG_SYS_CPU and CONFIG_SYS_VENDOR
values are the same for the entire Layerscape family,
meaning there is no ability to create a LS1088A only
file here. But we will be adding per-board tweaks
later in any case.
Reviewed-by: Peng Fan <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
Reviewed-by: Ioana Ciornei <[email protected]>
Tested-by: Ioana Ciornei <[email protected]> # on LS1088A-RDB
|
|
The recent series "Convert LS1088A and LX2160 to DM_SERIAL"
from Ioana Ciornei provided the necessary support to enable
DM_SERIAL on the Ten64 board (LS1088A).
Signed-off-by: Mathew McBride <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
Reviewed-by: Ioana Ciornei <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
Reviewed-by: Ioana Ciornei <[email protected]>
Tested-by: Ioana Ciornei <[email protected]> # on LS1088A-RDB
|
|
This a problem I found while updating the U-Boot fsl-ls1088a.dtsi
to match the Linux version.
fdt_fixup_remove_jr did not check whether there was a "crypto"
alias in the device tree before calling more fdt_* functions,
which resulted in a crash.
Fixes: a797f274
("ARMv8/sec_firmware : Update chosen/kaslr-seed with random number")
Signed-off-by: Mathew McBride <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
Reviewed-by: Ioana Ciornei <[email protected]>
Tested-by: Ioana Ciornei <[email protected]> # on LS1088A-RDB
|
|
- Clean up / merge some defconfigs, update DDR timings and a few more
assorted fixes.
|
|
Update the DDR settings to those generated using 0.6 version of
Jacinto 7 DDRSS Register Configuration tool.
Signed-off-by: Neha Malcom Francis <[email protected]>
Reviewed-by: Bryan Brattlof <[email protected]>
|
|
Update the DDR settings to those generated using 0.9.1 version of
Jacinto 7 DDRSS Register Configuration tool.
Signed-off-by: Neha Malcom Francis <[email protected]>
Reviewed-by: Bryan Brattlof <[email protected]>
|
|
K3 devices have runtime type board detection. Make the default defconfig
include the secure configuration. Then remove the HS specific config.
Non-HS devices will continue to boot due to runtime device type detection.
If TI_SECURE_DEV_PKG is not set the build will emit warnings, for non-HS
devices these can be ignored.
Reviewed-by: Kamlesh Gurudasani <[email protected]>
Signed-off-by: Manorit Chawdhry <[email protected]>
|
