| Age | Commit message (Collapse) | Author |
|---|
|
The NXP i.MXRT1170 Evaluation Kit (EVK) provides a platform for rapid
evaluation of the i.MXRT, which features NXP's implementation of the Arm
Cortex-M7 and Cortex-M4 core.
The EVK provides 64 MB SDRAM, Micro SD card socket,
USB 2.0 OTG.
This patch aims to support the preliminary booting up features
as follows:
GPIO
LPUART
SD/MMC
SDRAM
Signed-off-by: Jesse Taube <[email protected]>
|
|
Add binding header for i.MXRT1170 pinctrl device tree.
Signed-off-by: Jesse Taube <[email protected]>
|
|
This commit adds board support for i.MXRT1170-EVK from NXP. This board
is an evaluation kit provided by NXP for i.MXRT117x processor family.
Signed-off-by: Jesse Taube <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-mpc85xx
|
|
https://source.denx.de/u-boot/custodians/u-boot-watchdog into next
- Migrate watchdog reset to cyclic infrastructure (Stefan)
|
|
- mvebu: turris_omnia: Fix setting switch CONFIG pins on new board
design (Marek)
- orion-timer: Use timer_conv_64() to fix timer wrap around (Stefan)
|
|
While testing on some Kirkwood platforms it was noticed that the timer
did not function correctly all the time. The driver did not correctly
handle 32bit timer value wrap arounds. Using the timer_conv_64()
conversion function fixes this issue.
Fixes: e9e73d78a8fb ("timer: add orion-timer support")
Suggested-by: Stefan Herbrechtsmeier <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
Tested-by: Tony Dinh <[email protected]>
|
|
It seems that waiting only 10 ms after releasing LAN switch from reset
is not enough for the strapping pins to latch the requested values.
P6_MODE[0] is latched to 0 instead of 1.
Increasing the delay to 50 ms fixes this issue.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Remove some now unused macros and #ifdef's.
Signed-off-by: Stefan Roese <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Tested-by: Tom Rini <[email protected]> [am335x_evm, mx6cuboxi, rpi_3,dra7xx_evm, pine64_plus, am65x_evm, j721e_evm]
|
|
Now that we've globally replaced all WATCHDOG_RESET occurances, let's
remove the ugly macro itself in the header.
Signed-off-by: Stefan Roese <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Tested-by: Tom Rini <[email protected]> [am335x_evm, mx6cuboxi, rpi_3,dra7xx_evm, pine64_plus, am65x_evm, j721e_evm]
|
|
Only one occurance of WATCHDOG_RESET is left in one assembler file.
This patch changes this occurance to a direct call to watchdog_reset
and then removes all the ASSEMBLY ifdef'ery in watchdog.h, as it's not
needed any more to clean this mess a bit up.
Signed-off-by: Stefan Roese <[email protected]>
Tested-by: Tom Rini <[email protected]> [am335x_evm, mx6cuboxi, rpi_3,dra7xx_evm, pine64_plus, am65x_evm, j721e_evm]
|
|
Globally replace all occurances of WATCHDOG_RESET() with schedule(),
which handles the HW_WATCHDOG functionality and the cyclic
infrastructure.
Signed-off-by: Stefan Roese <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Tested-by: Tom Rini <[email protected]> [am335x_evm, mx6cuboxi, rpi_3,dra7xx_evm, pine64_plus, am65x_evm, j721e_evm]
|
|
This patch introduces a schedule() function, which shall be used instead
of the old WATCHDOG_RESET. Follow-up patches will make sure, that this
new function is used.
Signed-off-by: Stefan Roese <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Tested-by: Tom Rini <[email protected]> [am335x_evm, mx6cuboxi, rpi_3,dra7xx_evm, pine64_plus, am65x_evm, j721e_evm]
|
|
This patch integrates the watchdog triggering into the recently added
cyclic infrastructure. Each watchdog device that shall be triggered
registers it's own cyclic function. This way, multiple watchdog devices
are still supported, each via a cyclic function with separate trigger
intervals.
Signed-off-by: Stefan Roese <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Tested-by: Tom Rini <[email protected]> [am335x_evm, mx6cuboxi, rpi_3,dra7xx_evm, pine64_plus, am65x_evm, j721e_evm]
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
The block interface has two separate implementations, one using driver
model and one not. The latter is really only needed for SPL, where
size constraints allegedly don't allow use of driver model. Of course
we still need space for filesystems and other code, so it isn't clear
that driver model is anything more than the straw that breaks the
camel's back.
The driver model version uses a uclass ID for the interface time, but
converts back and forth between that and if_type, which is the legacy
type.
The HAVE_BLOCK_DEVICE define is mostly a hangover from the old days.
At present its main purpose is to enable the legacy block implementation
in SPL.
Finally the use of 'select' to enable BLK does not work very well. It
causes kconfig errors when another option depends on BLK and it is
not recommended by the kconfig style guide.
This series aims to clean things up:
- Enable BLK based on whether different media types are used, but still
allow boards to disable it
- Rename HAVE_BLOCK_DEVICE to indicates its real purpose
- Drop if_type and use the uclass instead
- Drop some obsolete if_type values
An issue not resolved by this series is that the sandbox host interface
does not actually have a device. At present it uses the root device, which
was convenience for the driver model conversion but not really correct. It
should be possible to clean this up, in a future series.
Another minor issue is the use of UCLASS_USB for a mass-storage device.
This has been the case for a while and is not addresed by this series,
other than to add a comment.
Note that this test relies on Tom Rini's series to drop various boards
including warp and cm_t335
Finally, a patch is included to make binman put fake files in a
subdirectory, since repeated runs of certain boards can cause unrelated
failues (e.g. chromebook_coral) when fake files are left around.
|
|
When fixed offset via CONFIG_SYS_MMC_U_BOOT_OFFS is not specified then
expects that U-Boot proper is placed immediately after SPL without any
additional padding.
This allows to generate smaller SPL+U-Boot final binary as it is not
required to specify fixed offset to U-Boot proper at SPL compile time.
In this case offset to U-Boot proper is calculated at SPL compile time in
linker script.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Jaehoon Chung <[email protected]>
Signed-off-by: Marek Behún <[email protected]>
|
|
Change 8-byte alignment of SPL binary to just 4-byte alignment as objcopy
trims trailing zero bytes when converting ELF file to RAW binary.
This is same fix for SPL linker script as was done fix for U-Boot linker
script in commit e8c0e0064c8a ("powerpc: mpc85xx: Fix CONFIG_OF_SEPARATE
support").
It is required for the patch "mmc: fsl_esdhc_spl: Add support for builds
without CONFIG_SYS_MMC_U_BOOT_OFFS" which triggered this issue in SPL.
Signed-off-by: Pali Rohár <[email protected]>
Signed-off-by: Marek Behún <[email protected]>
|
|
location
This allows to concatenate SPL and proper U-Boot without extra alignment.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Jaehoon Chung <[email protected]>
Signed-off-by: Marek Behún <[email protected]>
|
|
Commit d433c74eecdc ("Convert CONFIG_SDCARD et al to Kconfig") converted
SYS_EXTRA_OPTIONS=SDCARD or SPIFLASH to config options CONFIG_SDCARD and
CONFIG_SPIFLASH, but left one occurance unchanged.
Fix this.
Fixes: d433c74eecdc ("Convert CONFIG_SDCARD et al to Kconfig")
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Pali Rohár <[email protected]>
|
|
Use 'CONFIG_MPC85XX_HAVE_RESET_VECTOR && CONFIG_OF_SEPARATE' pattern
instead of 'CONFIG_MPC85XX_HAVE_RESET_VECTOR && !CONFIG_OF_EMBED' also in
OBJCOPYFLAGS_u-boot-nodtb.bin as this pattern is used in rest of Makefile.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Marek Behún <[email protected]>
|
|
Building of final u-boot.bin binary for mpc85xx via binman is needed only
when inserting DTB binary in the middle of the u-boot ELF binary (before
.bootpg and .resetvec ELF sections).
These requirements are met when CONFIG_MPC85XX_HAVE_RESET_VECTOR is enabled
(= generating .bootpg/.resetvec sections) and CONFIG_OF_SEPARATE is enabled
(= inserting DTB binary).
So in all other cases use standard build procedure instead of custom
mpc85xx u-boot.bin Makefile target via binman.
Signed-off-by: Pali Rohár <[email protected]>
Signed-off-by: Marek Behún <[email protected]>
|
|
Currently Makefile produces final mpc85xx image when SPL is not used in
custom file u-boot-with-dtb.bin. It is quite confusing name as build
process produce also intermediate file standard file u-boot-dtb.bin (which
is just intermediate and not bootable). Other platforms use u-boot.bin
(UBOOT_BIN) as standard name for final bootable raw image.
So change Makefile rules and binman to produce final bootable file for
mpc85xx also into file u-boot.bin. There is just need for mpc85xx to not
define default rule for u-boot.bin then instruct binman (via DTS file) to
store final image into u-boot.bin (instead of u-boot-with-dtb.bin) and
finally rename target u-boot-with-dtb.bin to u-boot.bin.
With this change are also removed custom Makefile hacks for mpc85xx that it
produced non-standard output file. And also updated documentation.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Signed-off-by: Marek Behún <[email protected]>
|
|
Makefile uses binman to produce u-boot-with-dtb.bin target. As its input it
takes DTB file and u-boot binary without DTB, which is stored in file
u-boot-nodtb.bin. So fix target dependency.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Marek Behún <[email protected]>
|
|
Use the uclass ID instead.
Signed-off-by: Simon Glass <[email protected]>
Acked-by: Heinrich Schuchardt <[email protected]>
|
|
This is currently missing. Add it.
Fix the code style for the function while we are here.
Suggested-by: AKASHI Takahiro <[email protected]>
Signed-off-by: Simon Glass <[email protected]>
|
|
We currently have an if_type (interface type) and a uclass id. These are
closely related and we don't need to have both.
Drop the if_type values and use the uclass ones instead.
Maintain the existing, subtle, one-way conversion between UCLASS_USB and
UCLASS_MASS_STORAGE for now, and add a comment.
Signed-off-by: Simon Glass <[email protected]>
|
|
efi_set_blk_dev_to_system_partition() assumes that 0 is an invalid
if_type. This is true now but is about to be false. Fix this bug to avoid
a test failure.
Signed-off-by: Simon Glass <[email protected]>
|
|
These are currently using a simple array lookup in one direction, and
relying on if_type being sequential.
With the move to uclass IDs this needs to change. Update the code to
prepare for the new way. This patch is intended to introduce no
functional change.
The returning of "(none)" from blk_get_if_type_name() is handling a case
that should not happen in either case.
Signed-off-by: Simon Glass <[email protected]>
|
|
At present we use a variable with the same name as the enum. Change this
since we plan to #define the enum to uclass_id.
Signed-off-by: Simon Glass <[email protected]>
|
|
This is not really needed since it does the same things as MMC. Drop it.
Signed-off-by: Simon Glass <[email protected]>
|
|
This is not really needed since it does the same things as IDE. Drop it.
Signed-off-by: Simon Glass <[email protected]>
|
|
Rather than setting a different interface type, use a flag to indicate
that a device is ATAPI.
Signed-off-by: Simon Glass <[email protected]>
|
|
This doesn't seem to be used for anything and it isn't clear what it is.
It dates from the first U-Boot commit.
Drop it.
Signed-off-by: Simon Glass <[email protected]>
|
|
We don't want boards to be able to change these. They can be handled
as dependencies of options that need them, such as SPL_MMC. There is no
point in enabling the block interface without any storage devices to
create a block device.
Hide both options from the 'menuconfig' display and deny their use in
defconfig files.
Signed-off-by: Simon Glass <[email protected]>
|
|
This is defined automatically when needed, so drop it from the few
defconfig files that define it manually.
Signed-off-by: Simon Glass <[email protected]>
|
|
Selecting this option can be handled in the Kconfig option itself, as it
is with BLK. Update this an drop the various 'select' clauses.
Signed-off-by: Simon Glass <[email protected]>
|
|
This option is fact really related to SPL. For U-Boot proper we always use
driver model for block devices, so CONFIG_BLK is enabled if block devices
are in use.
It is only for SPL that we have two cases:
- SPL_BLK is enabled, in which case we use driver model and blk-uclass.c
- SPL_BLK is not enabled, in which case (if we need block devices) we must
use blk_legacy.c
Rename the symbol to SPL_LEGACY_BLOCK to make this clear. This is
different enough from BLK and SPL_BLK that there should be no confusion.
Signed-off-by: Simon Glass <[email protected]>
|
|
We can rely on the compiler to eliminate any dead code.
Signed-off-by: Simon Glass <[email protected]>
|
|
This condition is not needed for these commands, since BLK is enabled for
all boards which use block devices and commands are not available in SPL,
so even if SPL_BLK is not enabled, it doesn't affect commands.
Signed-off-by: Simon Glass <[email protected]>
|
|
At present we use HAVE_BLOCK_DEVICE to indicate when block devices are
available.
This is a very strange option, since it partially duplicates the BLK
option used by driver model. It also covers both U-Boot proper and SPL,
even though one might have block devices and another not.
As a first step towards correcting this, create a new inline function
called blk_enabled() which indicates if block devices are available.
This cannot be used in Makefiles, or #if clauses, but can be used in C
code.
A function is useful because we cannot use CONFIG_IS_ENABLED(BLK) to
decide if block devices are needed, since we must consider the legacy
block interface, enabled by HAVE_BLOCK_DEVICE
Update a few places where it can be used and drop some unnecessary #if
checks around some functions in disk/part.c - rely on the compiler's
dead-code elimination instead.
Signed-off-by: Simon Glass <[email protected]>
|
|
At present these files have an #ifdef covering the whole file. Move the
condition to the Makefile instead.
Add BLK to the condition since future patches will adjust things so that
HAVE_BLOCK_DEVICE is only for SPL, but the partition drivers are needed
in U-Boot proper too.
Signed-off-by: Simon Glass <[email protected]>
|
|
This is not needed as it is implied or selected by other options anyway.
Signed-off-by: Simon Glass <[email protected]>
|
|
The _SUPPORT suffix should be dropped. This happened because the rename
was applied around the same time as this new option, so did not include
renaming the new option.
The relevant commits are:
f7560376ae sata: Rename SATA_SUPPORT to SATA
73059529b2 ata: ahci-pci: Add new option CONFIG_SPL_AHCI_PCI
Fix it.
Signed-off-by: Simon Glass <[email protected]>
|
|
Enable this option on all boards which support block devices. Drop the
related depencies on BLK since these are not needed anymore.
Disable BLOCK_CACHE on M5253DEMO as this causes a build error.
Signed-off-by: Simon Glass <[email protected]>
|
|
Fix a few typos in this help text. Fix a typo in SPL_PARTITIONS while
we are here.
Signed-off-by: Simon Glass <[email protected]>
|
|
- Updated for assorted platforms using various TI SoCs.
|
|
Compile U-Boot with UBI/UBIFS support according to doc/board/nokia/rx51.rst
instructions and add test case for loading kernel image from UBI volume.
Signed-off-by: Pali Rohár <[email protected]>
|
|
Signed-off-by: Pali Rohár <[email protected]>
|
|
U-Boot ignores ARCH= variable.
Signed-off-by: Pali Rohár <[email protected]>
|
