| Age | Commit message (Collapse) | Author |
|---|
|
The Cubox has an unstable phy address - which can appear at either
address 0 (intended) or 4 (unintended).
SoM revision 1.9 has replaced the ar8035 phy with an adin1300, which
will always appear at address 1.
Change the reg property of the phy node to the magic value 0xffffffff,
which indicates to the generic phy driver that all addresses should be
probed. That allows the same node (which is pinned by phy-handle) to match
either the AR8035 PHY at both possible addresses, as well as the new one
at address 1.
Also add the new adi,phy-output-clock property for enabling the 125MHz
clock used by the fec ethernet controller, as submitted to Linux [1].
Linux solves this problem differently:
For the ar8035 phy it will probe both phy nodes in device-tree in order,
and use the one that succeeds. For the new adin1300 it expects U-Boot to
patch the status field in the DTB before booting
While at it also sync the reset-delay with the upstream Linux dtb.
[1] https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/
Signed-off-by: Josua Mayer <[email protected]>
|
|
The ADIN1300 supports generating certain clocks on its GP_CLK pin, as
well as providing the reference clock on CLK25_REF.
Add support for selecting the clock via device-tree properties.
This patch is based on the Linux implementation for this feature,
which has been added to netdev/net-next.git [1].
[2] https://patchwork.kernel.org/project/netdevbpf/cover/[email protected]/
Signed-off-by: Josua Mayer <[email protected]>
|
|
Currently, the adin driver fails to compile.
The original patch introducing the adin driver used the function
phy_get_interface_by_name to support the adi,phy-mode-override
property. Unfortunately, a few days before the adin patch
was accepted, another patch removed support for phy_get_interface_by_name:
https://github.com/u-boot/u-boot/commit/123ca114e07ecf28aa2538748d733e2b22d8b8b5
This patch refactors adin_get_phy_mode_override, implementing the logic in
the new function, ofnode_read_phy_mode, from the patch above.
Signed-off-by: Nate Drude <[email protected]>
Tested-by: Josua Mayer <[email protected]>
Signed-off-by: Josua Mayer <[email protected]>
|
|
The imx8mn-ddr4-evk board has Ethernet support already, but the
lpddr4 board does not.
Add Ethernet support for the LPDDR4 variant too.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
Add the new Apalis iMX8 product variant
0067: Apalis iMX8 QuadMax 8GB Wi-Fi / BT IT
the only difference to the product
0037 Apalis iMX8 QuadMax 4GB Wi-Fi / BT IT
is the 8gb of RAM. Toradex strategy to choose the correct RAM timing in
SCFW is by fuses in the user area telling which RAM timing to load.
This commit makes use of this information to set the correct size of
the RAM and therefore distinguish between the new 0067 and 0037 product
Signed-off-by: Philippe Schenker <[email protected]>
Reviewed-by: Francesco Dolcini <[email protected]>
Acked-by: Marcel Ziswiler <[email protected]>
|
|
0067: Apalis iMX8 QuadMax 8GB Wi-Fi / BT IT
This module is identical to its 4GB counterpart
0037: Apalis iMX8 QuadMax 4GB Wi-Fi / BT IT
except for the RAM size.
Signed-off-by: Philippe Schenker <[email protected]>
Reviewed-by: Francesco Dolcini <[email protected]>
Acked-by: Marcel Ziswiler <[email protected]>
|
|
The generated flash.bin does not boot the imx8mn evk LPDDR4 variant
as it misses the spl.bin description in binman.
Add its entry to fix the boot on the imx8mn evk LPDDR4 variant.
Signed-off-by: Fabio Estevam <[email protected]>
Tested-by: Arti Zirk <[email protected]>
Reviewed-by: Alper Nebi Yasak <[email protected]>
|
|
This test was written to match up with the list of compatibles in
drivers/i2c/tegra_i2c.c so adding another one requires the test to be
updated to match.
Fixes: 0d2105ae5e32 ("arm: tegra: Update some DT compatibles")
Signed-off-by: Tom Rini <[email protected]>
|
|
Signed-off-by: Tom Rini <[email protected]>
|
|
The pca9450 driver uses dm_i2c_{read,write}, which
are (unsurprisingly) only available with DM_I2C. Make sure one can't
create an unbuildable .config by adding proper dependencies.
While here, append "in SPL" to the prompt for the SPL_ variant so it
doesn't read the same as the one for the non-SPL_ variant.
Signed-off-by: Rasmus Villemoes <[email protected]>
Reviewed-by: Jaehoon Chung <[email protected]>
|
|
Use device tree to set MAC address of the Ethernet chip.
Signed-off-by: Marcel Ziswiler <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Some of the DT compatibles have changed upstream so add new DT compatibles
to ensure things continue to keep working if the device trees are
updated.
Signed-off-by: Peter Robinson <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Add new lines to make errorr messages easier to read.
Signed-off-by: Peter Robinson <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Add new lines for error messages to make them easier to read.
Signed-off-by: Peter Robinson <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-07-rc5
UEFI:
* Ignore OsIndications if CONFIG_EFI_IGNORE_OSINDICATIONS=y
* Correct UEFI default binary name
* Let efidebug create boot options without file path
* Support booting with a boot option with shortened device only device path
|
|
Allow the efidebug command to create boot options without file path, e.g.
efidebug boot add -b 0001 'short dev only' host 0:1 ''
efidebug boot add -B 0002 'long dev only' host 0:1 ''
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
Allow booting from a short form device-path without file path, e.g.
/HD(1,GPT,5ef79931-a1aa-4c70-9d67-611e8f69eafd,0x800,0x1000)
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
Only on the sandbox the default EFI binary name (e.g. BOOTX64.EFI) must
match the host architecture.
In all other cases we must use the target architecture.
Use #elif where appropriate.
Reported-by: Vagrant Cascadian <[email protected]>
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
The GetImageInfo function definitions for the FIT images and raw
images are the same. Use a common function for the both the Firmware
Management Protocol(FMP) instances for raw and FIT images.
Signed-off-by: Sughosh Ganu <[email protected]>
Reviewed-by: Heinrich Schuchardt <[email protected]>
|
|
CONFIG_EFI_IGNORE_OSINDICATIONS is enabled
The EFI_IGNORE_OSINDICATIONS config symbol was introduced as a
mechanism to have capsule updates work even on platforms where the
SetVariable runtime service was not supported. The current logic
requires the OsIndications variable to have been set to a 64 bit value
even when the EFI_IGNORE_OSINDICATIONS config is enabled. Return an
error code on not being able to read the variable only when
EFI_IGNORE_OSINDICATIONS is not enabled.
Signed-off-by: Sughosh Ganu <[email protected]>
Reviewed-by: Heinrich Schuchardt <[email protected]>
|
|
- TI J721E hyperflash support, TI OMAP3 updates, TI AM654 updates,
TI AM62 initial support, Broadcom bcmbca 47622 SoC support, NPCM7xx
pinctrl and rng drivers, Synquacer updates
|
|
Add info of boot flow and build steps for AM62x SK.
Signed-off-by: Vignesh Raghavendra <[email protected]>
Reviewed-by: Bryan Brattlof <[email protected]>
|
|
Add am62x_evm_r5_defconfig for R5 SPL and am62x_evm_a53_defconfig for
A53 SPL and U-Boot support.
To keep the changes to minimum. Only UART And SD boot related configs
are included. This should serve as good starting point for new board
bringup with AM62x.
Signed-off-by: Aswath Govindraju <[email protected]>
Signed-off-by: Vignesh Raghavendra <[email protected]>
[trini: Migrate a number of CONFIG symbols, have re-tested]
Tested-by: Georgi Vlaev <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
AM62 StarterKit (SK) board is a low cost, small form factor board
designed for TI’s AM625 SoC. It supports the following interfaces:
* 2 GB DDR4 RAM
* x2 Gigabit Ethernet interfaces capable of working in Switch and MAC mode
* x1 HDMI Port with audio + x1 OLDI/LVDS Display interface for Dual Display
* x1 Headphone Jack
* x1 USB2.0 Hub with two Type A host and x1 USB Type-C DRP Port
* x1 UHS-1 capable µSD card slot
* 2.4/5 GHz WLAN + Bluetooth 4.2 through WL1837
* 512 Mbit OSPI flash
* x4 UART through UART-USB bridge
* XDS110 for onboard JTAG debug using USB
* Temperature sensors, user push buttons and LEDs
* 40-pin User Expansion Connector
* 24-pin header for peripherals in MCU island (I2C, UART, SPI, IO)
* 20-pin header for Programmable Realtime Unit (PRU) IO pins
* 15-pin CSI header
Add basic support for AM62-SK.
To keep the changes to minimum. Only UART And SD are supported at the
moment. This should serve as good example for adding new board support
based on AM62x SoC
Schematics: https://www.ti.com/lit/zip/sprr448
Signed-off-by: Nishanth Menon <[email protected]>
Signed-off-by: Aswath Govindraju <[email protected]>
Signed-off-by: Nishanth Menon <[email protected]>
Signed-off-by: Dave Gerlach <[email protected]>
Signed-off-by: Vignesh Raghavendra <[email protected]>
|
|
Add basic support for AM62 SK. This has 2GB DDR.
Note that stack for R5 SPL is in OCRAM @ 0x7000ffff so that is away from
BSS and does not step on BSS section
Add only the bare minimum required to support UART and SD.
Signed-off-by: Suman Anna <[email protected]>
Signed-off-by: Aswath Govindraju <[email protected]>
Signed-off-by: Nishanth Menon <[email protected]>
Signed-off-by: Vignesh Raghavendra <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Introduce the basic AM62 SoC description dtsi files describing most
peripherals as per kernel dts.
Signed-off-by: Gowtham Tammana <[email protected]>
Signed-off-by: Suman Anna <[email protected]>
Signed-off-by: Vignesh Raghavendra <[email protected]>
|
|
Add range of DMA channels available for R5 SPL usage before DM firmware
is loaded.
Signed-off-by: Vignesh Raghavendra <[email protected]>
|
|
Add PSIL data for AM62x SoC.
Signed-off-by: Vignesh Raghavendra <[email protected]>
|
|
Introduce autogenerated SoC data support clk and device data for the
AM62. Hook it upto to power-domain and clk frameworks of U-Boot.
Signed-off-by: Dave Gerlach <[email protected]>
Signed-off-by: Suman Anna <[email protected]>
Signed-off-by: Vignesh Raghavendra <[email protected]>
|
|
The AM62 SoC family is the follow on AM335x built on K3 Multicore SoC
architecture platform, providing ultra-low-power modes, dual display,
multi-sensor edge compute, security and other BOM-saving integration.
The AM62 SoC targets broad market to enable applications such as
Industrial HMI, PLC/CNC/Robot control, Medical Equipment, Building
Automation, Appliances and more.
Some highlights of this SoC are:
* Quad-Cortex-A53s (running up to 1.4GHz) in a single cluster.
Pin-to-pin compatible options for single and quad core are available.
* Cortex-M4F for general-purpose or safety usage.
* Dual display support, providing 24-bit RBG parallel interface and
OLDI/LVDS-4 Lane x2, up to 200MHz pixel clock support for 2K display
resolution.
* Selectable GPUsupport, up to 8GFLOPS, providing better user experience
in 3D graphic display case and Android.
* PRU(Programmable Realtime Unit) support for customized programmable
interfaces/IOs.
* Integrated Giga-bit Ethernet switch supporting up to a total of two
external ports (TSN capable).
* 9xUARTs, 5xSPI, 6xI2C, 2xUSB2, 3xCAN-FD, 3x eMMC and SD, GPMC for
NAND/FPGA connection, OSPI memory controller, 3xMcASP for audio,
1x CSI-RX-4L for Camera, eCAP/eQEP, ePWM, among other peripherals.
* Dedicated Centralized System Controller for Security, Power, and
Resource Management.
* Multiple low power modes support, ex: Deep sleep,Standby, MCU-only,
enabling battery powered system design.
AM625 is the first device of the family. Add DT bindings for the same.
More details can be found in the Technical Reference Manual:
https://www.ti.com/lit/pdf/spruiv7
Signed-off-by: Suman Anna <[email protected]>
Signed-off-by: Gowtham Tammana <[email protected]>
Signed-off-by: Aswath Govindraju <[email protected]>
Signed-off-by: Nishanth Menon <[email protected]>
Signed-off-by: Vignesh Raghavendra <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Add support for AM62x SoC identification.
Signed-off-by: Suman Anna <[email protected]>
Signed-off-by: Vignesh Raghavendra <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Add pinctrl macros for AM62x SoCs. These macro definitions are similar
to that of previous platforms, but adding new definitions to avoid any
naming confusions in the SoC dts files.
checkpatch insists the following error exists:
ERROR: Macros with complex values should be enclosed in parentheses
However, we do not need parentheses enclosing the values for this
macro as we do intend it to generate two separate values as has been
done for other similar platforms.
Signed-off-by: Suman Anna <[email protected]>
Signed-off-by: Vignesh Raghavendra <[email protected]>
|
|
The phy used in the 8 bit instance has been changed to the phy used in 4
bit instance on AM62 SoC. This implies the phy configuration required for
both the instances of mmc are similar. Therefore, add a new compatible
for AM62 SoC using the driver data of am64 4 bit instance.
Signed-off-by: Aswath Govindraju <[email protected]>
Signed-off-by: Vignesh Raghavendra <[email protected]>
Reviewed-by: Jaehoon Chung <[email protected]>
|
|
Add Nuvoton BMC NPCM750 rng driver.
Signed-off-by: Jim Liu <[email protected]>
|
|
stack from generic r5 defconfig
Sync the configs required for enabling checks for size of image and stack
from generic r5 defconfig file.
Signed-off-by: Aswath Govindraju <[email protected]>
|
|
performed for usb boot
The node name of the bus in the device tree has changed. Also, the length
argument to be passed should be the length of new value. Therefore, fix the
path to usb device tree node as well as the length argument passed.
Signed-off-by: Aswath Govindraju <[email protected]>
|
|
For dfu boot mode, the clocks property needs to be deleted and dr_mode
needs to be set to peripheral. Therefore, add the required fixes for the
same.
Signed-off-by: Aswath Govindraju <[email protected]>
|
|
There is a TX-FIFO and Shift Register empty(TFES) status
bit in spi controller. This commit checks the TFES bit
to wait the TX transfer completes.
Signed-off-by: Masahisa Kojima <[email protected]>
Signed-off-by: Satoru Okamoto <[email protected]>
Acked-by: Jassi Brar <[email protected]>
|
|
DMSTART bit must not be set while there is active transfer.
This commit sets the DMSTART bit only when the transfer begins.
Signed-off-by: Masahisa Kojima <[email protected]>
Signed-off-by: Satoru Okamoto <[email protected]>
Acked-by: Jassi Brar <[email protected]>
|
|
synquacer_cs_set() function does not wait the chip select
is deasserted when the driver sets the DMSTOP to deselect
the slave.
This commit checks the Slave Select Released(SRS) bit to wait
until the slave is deselected.
Signed-off-by: Masahisa Kojima <[email protected]>
Signed-off-by: Satoru Okamoto <[email protected]>
Acked-by: Jassi Brar <[email protected]>
|
|
"busy" variable is ORed without being initialized,
must be zeroed before use.
Signed-off-by: Masahisa Kojima <[email protected]>
Signed-off-by: Satoru Okamoto <[email protected]>
Acked-by: Jassi Brar <[email protected]>
|
|
Add Nuvoton BMC NPCM750 Pinmux and Pinconf support.
Signed-off-by: Jim Liu <[email protected]>
|
|
This commit sets two additional variables in the default BOOTCOMMAND.
Adding 'boot=mmc' and 'addr_fit=0x8b000000' removes the need for a
special 'uEnv.txt' to be created. The 'addr_fit' variable is the key
piece here. It is normally defined as 0x90000000, in the macro
DEFAULT_FIT_TI_ARGS. For this OMAP34XX board, 0x8b000000 works without
touching other varibles. This was tested with a 'fitImage' created
using the following FIT source:
----------------------------------------------------------------------
/dts-v1/;
/ {
description = "Simple image with single Linux kernel and FDT blob";
#address-cells = <1>;
images {
kernel {
description = "Linux kernel: omap2plus";
data = /incbin/("./zImage");
type = "kernel";
arch = "arm";
os = "linux";
compression = "none";
load = <0x80008000>;
entry = <0x80008000>;
hash-1 {
algo = "sha256";
};
};
fdt-omap3-evm.dtb {
description = "FDT: omap3-evm.dtb";
data = /incbin/("./omap3-evm.dtb");
type = "flat_dt";
arch = "arm";
compression = "none";
load = <0x8ff00000>;
hash-1 {
algo = "sha256";
};
};
};
configurations {
default = "conf-omap3-evm.dtb";
conf-omap3-evm.dtb {
description = "Boot Linux kernel with FDT blob";
kernel = "kernel";
fdt = "fdt-omap3-evm.dtb";
};
};
};
----------------------------------------------------------------------
Additionally, the default environment is now stored in "uboot.env" on
the FAT partition of MMC '0'.
Fixes: 11e2ab3f0b ("ARM: omap3: evm: Enable booting 'fitImage' with DEFAULT_FIT_TI_ARGS")
Signed-off-by: Derald D. Woods <[email protected]>
|
|
This commits enables DM_I2C and sets the default bus to 0.
Signed-off-by: Derald D. Woods <[email protected]>
|
|
This commit copies the related code changes from the BeagleBoard.
Reference:
- https://source.denx.de/u-boot/u-boot/-/commit/848cfe098f59c47a2542385513fb554430b874d6
Signed-off-by: Derald D. Woods <[email protected]>
|
|
This is the initial support for Broadcom's ARM-based 47622 SOC.
In this change, our first SOC is an armv7 platform called 47622. The
initial support includes a bare-bone implementation and dts with ARM
PL011 uart.
The SOC-specific code resides in arch/arm/mach-bcmbca/<soc> and board
related code is in board/broadcom/bcmba.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there.
Signed-off-by: William Zhang <[email protected]>
Signed-off-by: Kursad Oney <[email protected]>
Signed-off-by: Anand Gore <[email protected]>
Reviewed-by: Philippe Reynes <[email protected]>
|
|
Enable HBMC and HyperFlash in R5SPL, A72 SPL and A72 U-Boot
Signed-off-by: Vaishnav Achath <[email protected]>
[trini: Update j721e_hs_evm_a72 as well]
Signed-off-by: Tom Rini <[email protected]>
|
|
On j721e, its not possible to use OSPI0 and HBMC simultaneously as they
are muxed within the Flash Subsystem hence disable HBMC by default and
keep OSPI enabled. Bootloader will fixup DT when it detects HyperFlash
mux selection instead of OSPI.
Also updated detect_enable_hyperflash to use correct GPIO when checking
hypermux selection state:
* J7200 - hypermux sel connected to WKUP_GPIO0_6
* J721E - hypermux·sel·connected·to·WKUP_GPIO0_8
Signed-off-by: Vaishnav Achath <[email protected]>
|
|
Define CONFIG_SYS_FLASH_BASE to indicate start address of
Flash memory
Signed-off-by: Vaishnav Achath <[email protected]>
|
|
add support for loading system firmware from hyperflash.
Signed-off-by: Vaishnav Achath <[email protected]>
|
