| Age | Commit message (Collapse) | Author |
|---|
|
commit ffb0f6f488b9 ("treewide: Rename PHY_INTERFACE_MODE_NONE to
PHY_INTERFACE_MODE_NA") broke the phy_string_for_interface function.
Fix it.
Fixes ffb0f6f488b9 ("treewide: Rename PHY_INTERFACE_MODE_NONE to PHY_INTERFACE_MODE_NA")
Signed-off-by: Tim Harvey <[email protected]>
Cc: Marek Behún <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: Ramon Fried <[email protected]>
Cc: Vladimir Oltean <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
|
|
Add the tpm2_tis_i2c driver that should support any TPMv2 compliant
I2C chips, such as the NPCT75X chip.
[Ilias rename priv_auto_alloc_size to priv_auto]
Signed-off-by: Eddie James <[email protected]>
Reviewed-by: Joel Stanley <[email protected]>
Reviewed-by: Ilias Apalodimas <[email protected]>
Signed-off-by: Ilias Apalodimas <[email protected]>
|
|
Commit 0980cbba7b3c ("mmc: fsl_esdhc_spl: pre-PBL: implement redundancy
support") changed number of sectors which are read but did not adjusted
error check.
Fix it and check for if correct number of sectors were read.
Fixes: 0980cbba7b3c ("mmc: fsl_esdhc_spl: pre-PBL: implement redundancy support")
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Jaehoon Chung <[email protected]>
|
|
This would prevent configuring non-secure regs in case gic security
extensions are not emulated in Qemu.
Signed-off-by: Sai Pavan Boddu <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
case
In case _spi_get_bus_and_cs()'s parameters drv_name and dev_name are
respectively set to NULL and 0, use spi_get_bus_and_cs() instead.
Signed-off-by: Patrice Chotard <[email protected]>
Cc: Marek Behun <[email protected]>
Cc: Jagan Teki <[email protected]>
Cc: Vignesh R <[email protected]>
Cc: Joe Hershberger <[email protected]>
Cc: Ramon Fried <[email protected]>
Cc: Lukasz Majewski <[email protected]>
Cc: Marek Vasut <[email protected]>
Cc: Wolfgang Denk <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: "Pali Rohár" <[email protected]>
Cc: Konstantin Porotchkin <[email protected]>
Cc: Igal Liberman <[email protected]>
Cc: Bin Meng <[email protected]>
Cc: Pratyush Yadav <[email protected]>
Cc: Sean Anderson <[email protected]>
Cc: Anji J <[email protected]>
Cc: Biwen Li <[email protected]>
Cc: Priyanka Jain <[email protected]>
Cc: Chaitanya Sakinam <[email protected]>
|
|
Now, spi_flash_probe_bus_cs() relies on DT for spi speed and mode
and logically calls spi_get_bus_and_cs(). In case spi mode and speed are
not read from DT, make usage of spi_flash_probe() instead.
To sum-up:
- Previous call tree was:
spi_flash_probe() -> spi_flash_probe_bus_cs() -> spi_get_bus_and_cs()
- Current call tree is:
spi_flash_probe() -> _spi_get_bus_and_cs()
spi_flash_probe_bus_cs() -> spi_get_bus_and_cs()
This patch impacts the following :
- cmd/sf.c: if spi mode and/or speed is passed in argument of
do_spi_flash_probe(), call spi_flash_probe() otherwise call
spi_flash_probe_bus_cs().
- drivers/net/fm/fm.c: as by default spi speed and mode was set to
0 and a comment indicates that speed and mode are read from DT,
use spi_flash_probe_bus_cs().
- drivers/net/pfe_eth/pfe_firmware.c: spi speed and mode are not read
from DT by all platforms using this driver, so keep legacy and replace
spi_flash_probe_bus_cs() by spi_flash_probe();
- drivers/net/sni_netsec.c : spi speed and mode are not read from DT,
so replace spi_flash_probe_bus_cs() by spi_flash_probe().
- drivers/usb/gadget/max3420_udc.c: Can't find any platform which make
usage of this driver, nevertheless, keep legacy and replace
spi_get_bus_and_cs() by _spi_get_bus_and_cs().
- env/sf.c: a comment indicates that speed and mode are read
from DT. So use spi_flash_probe_bus_cs().
Signed-off-by: Patrice Chotard <[email protected]>
Cc: Marek Behun <[email protected]>
Cc: Jagan Teki <[email protected]>
Cc: Vignesh R <[email protected]>
Cc: Joe Hershberger <[email protected]>
Cc: Ramon Fried <[email protected]>
Cc: Lukasz Majewski <[email protected]>
Cc: Marek Vasut <[email protected]>
Cc: Wolfgang Denk <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: "Pali Rohár" <[email protected]>
Cc: Konstantin Porotchkin <[email protected]>
Cc: Igal Liberman <[email protected]>
Cc: Bin Meng <[email protected]>
Cc: Pratyush Yadav <[email protected]>
Cc: Sean Anderson <[email protected]>
Cc: Anji J <[email protected]>
Cc: Biwen Li <[email protected]>
Cc: Priyanka Jain <[email protected]>
Cc: Chaitanya Sakinam <[email protected]>
|
|
Move legacy spi_get_bus_and_cs() code to _spi_get_bus_and_cs().
Add new spi_get_bus_and_cs() implementation which rely on DT
for speed and mode and don't need any drv_name nor dev_name
parameters. This will prepare the ground for next patch.
Update all callers to use _spi_get_bus_and_cs() to keep the
same behavior.
Signed-off-by: Patrice Chotard <[email protected]>
Cc: Marek Behun <[email protected]>
Cc: Jagan Teki <[email protected]>
Cc: Vignesh R <[email protected]>
Cc: Joe Hershberger <[email protected]>
Cc: Ramon Fried <[email protected]>
Cc: Lukasz Majewski <[email protected]>
Cc: Marek Vasut <[email protected]>
Cc: Wolfgang Denk <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: "Pali Rohár" <[email protected]>
Cc: Konstantin Porotchkin <[email protected]>
Cc: Igal Liberman <[email protected]>
Cc: Bin Meng <[email protected]>
Cc: Pratyush Yadav <[email protected]>
Cc: Sean Anderson <[email protected]>
Cc: Anji J <[email protected]>
Cc: Biwen Li <[email protected]>
Cc: Priyanka Jain <[email protected]>
Cc: Chaitanya Sakinam <[email protected]>
|
|
mpc85xx NOR binary contains also reset vector and therefore option
CONFIG_MPC85XX_HAVE_RESET_VECTOR must be defined.
When build system uses binman, it takes care of constructing final image
which consist of u-boot-without-reset-vector, DTB and reset-vector.
CONFIG_OF_EMBED does not use binman, there is no external DTB and Makefile
produce directly final u-boot.bin binary.
So in this case mpc85xx reset vector must not be stripped from the final
u-boot.bin binary. Fix it.
Signed-off-by: Pali Rohár <[email protected]>
|
|
Commit e8c0e0064c8a ("powerpc: mpc85xx: Fix CONFIG_OF_SEPARATE support")
fixed SD card booting on mpc85xx boards but broke NOR booting on these
boards. Reason is that U-Boot build system for NOR images uses binman and
this binman ignores alignment defined in linker script. Instead it has own
config file where is alignment defined.
Fix binman alignment for mpc85xx boards to match what is _now_ defined in
linker script.
This change fixes building of U-Boot for NOR booting on P2020 board.
Fixes: e8c0e0064c8a ("powerpc: mpc85xx: Fix CONFIG_OF_SEPARATE support")
Signed-off-by: Pali Rohár <[email protected]>
|
|
When compling for x86:
ld.bfd: fs/squashfs/sqfs.o: in function `sqfs_read':
u-boot/fs/squashfs/sqfs.c:1443: undefined reference to `__udivmoddi4'
ld.bfd: u-boot/fs/squashfs/sqfs.c:1521: undefined reference to `__udivmoddi4'
Signed-off-by: Sean Nyekjaer <[email protected]>
Reviewed-by: Miquel Raynal <[email protected]>
Reviewed-by: Pali Rohár <[email protected]>
|
|
Requesting the locality uses the timeout values, so they need
to be set beforehand.
Signed-off-by: Eddie James <[email protected]>
Reviewed-by: Ilias Apalodimas <[email protected]>
Reviewed-by: Joel Stanley <[email protected]>
Signed-off-by: Ilias Apalodimas <[email protected]>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx-20220523
-------------------
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/12087
Additionally to u-boot-imx20200520:
- DH MX8MP
- i.MX GPIO: reading GPIO when direction is output
- Menlo i.MX53: switch to DM
And from u-boot-imx20200520:
- fix Verdin hang
- add pca9450 regulator
- conversion to DM_SERIAL
- NAND block handling
- fix crypto
- enable cache on some boards
- add ACC board (MX6)
|
|
Add support for DH electronics i.MX8M Plus DHCOM SoM on PDK2 carrier board.
Currently supported are serial console, EQoS and FEC ethernets, eMMC, SD,
SPI NOR and USB 3.0 host.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
|
|
Add support for reading GPIO pin value when function is output.
With this patch applied, gpio toggle command is working.
Signed-off-by: Christoph Fritz <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
Convert the board to DM I2C and DM RTC. This leads to removal of board
side iomuxc configuration, which is now done using pin control driver,
and conversion of board side legacy I2C accessors to DM ones.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Stefano Babic <[email protected]>
|
|
USB controller for AXG is described as meson-axg-usb-ctrl,
see arch/arm/dts/meson-axg.dtsi
Look for that name instead of meson-gxl-usb-ctrl.
Signed-off-by: Sergei Antonov <[email protected]>
Acked-by: Neil Armstrong <[email protected]>
Signed-off-by: Neil Armstrong <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The original Allwinner F1C100 .dtsi imported from the Linux kernel tree
used the wrong compatible string for the watchdog timer, so the Allwinner
DM reset driver was not working properly. We worked around this by
disabling the SYSRESET driver, so the hardcoded SPL reset driver took
over.
Now the issue was fixed in the DTs in mainline Linux, and we synced the
fixed .dtsi file into U-Boot, so drop the hack and use the normal U-Boot
proper reset infrastructure.
This reverts commit cfcf1952c11e6ffcbbf88eb63c49edca2acf1d5e.
Signed-off-by: Andre Przywara <[email protected]>
|
|
The initial U-Boot F1C100s port was based on the mainline kernel DT
files, which were quite basic and were missing the essential MMC and
SPI peripherals. While we could work around this in the SPL by
hardcoding the required information, this left U-Boot proper without SD
card or SPI flash support, so actual loading would require FEL boot.
Now the missing DT bits have been submitted and accepted in the kernel
tree, so lets sync back those files into U-Boot to enable MMC and
SPI, plus benefit from some fixes.
This is a verbatim copy of the .dts and .dtsi file from
linux-sunxi/dt-for-5.19[1], which have been part of linux-next for a
while as well.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux.git/log/?h=sunxi/dt-for-5.19
Link: https://lore.kernel.org/linux-arm-kernel/[email protected]/
Signed-off-by: Andre Przywara <[email protected]>
|
|
The f1c100s has a clock tree similar to those of other sunxi parts.
Add support for it.
Signed-off-by: George Hilliard <[email protected]>
Signed-off-by: Yifan Gu <[email protected]>
Acked-by: Sean Anderson <[email protected]>
[Andre: add PIO and I2C]
Signed-off-by: Andre Przywara <[email protected]>
|
|
Copy the devicetree source for the H6 SoC and all existing boards
from the Linux v5.18-rc1 tag.
To maintain ABI compatibility with existing LTS kernels, one change
moving some IP blocks to the r_intc interrupt controller is excluded.
This effectively reverts Linux commits 189bef235dd3 and 73088dfee635.
This commit also adds the following new board devicetrees:
- sun50i-h6-pine-h64-model-b.dts
- sun50i-h6-tanix-tx6-mini.dts
This update should not impact any existing U-Boot functionality.
Signed-off-by: Samuel Holland <[email protected]>
|
|
Copy the devicetree source for the A64 SoC and all existing boards
from the Linux v5.18-rc1 tag.
To maintain ABI compatibility with existing LTS kernels, one change
moving some IP blocks to the r_intc interrupt controller is excluded.
This effectively reverts Linux commits 189bef235dd3 and 73088dfee635.
This update should not impact any existing U-Boot functionality.
Signed-off-by: Samuel Holland <[email protected]>
|
|
Copy the devicetree for the R40/T3 SoC verbatim from the Linux v5.18-rc1
tag. None of the existing boards had any devicetree updates.
This commit adds the following new board devicetrees:
- sun8i-r40-oka40i-c.dts
- sun8i-t3-cqa3t-bv3.dts
Signed-off-by: Samuel Holland <[email protected]>
|
|
Copy the devicetree source for the V3(s)/S3 SoCs and all existing boards
verbatim from the Linux v5.18-rc1 tag.
This commit also adds the following new board devicetrees:
- sun8i-s3-elimo-initium.dts
- sun8i-v3-sl631-imx179.dts
This update should not impact any existing U-Boot functionality.
Signed-off-by: Samuel Holland <[email protected]>
|
|
Copy the devicetree source for the H2+/H3/H5 SoCs and all existing
boards from the Linux v5.18-rc1 tag.
To maintain ABI compatibility with existing LTS kernels, one change
moving some IP blocks to the r_intc interrupt controller is excluded.
This effectively reverts Linux commits 994e5818392c and 9fdef3c3d8c2.
This commit also adds the following new board devicetree:
- sun8i-h3-nanopi-r1.dts
This update should not impact any existing U-Boot functionality.
Signed-off-by: Samuel Holland <[email protected]>
|
|
Copy the devicetree source for the A83T SoC and all existing boards
from the Linux v5.18-rc1 tag.
To maintain ABI compatibility with existing LTS kernels, one change
moving some IP blocks to the r_intc interrupt controller is excluded.
This effectively reverts Linux commits 994e5818392c and 9fdef3c3d8c2.
As with the other SoCs, updates of note include adding detection GPIO
properties in the USB PHY nodes.
Signed-off-by: Samuel Holland <[email protected]>
|
|
Copy the devicetree source for the A80 SoC and all existing boards
verbatim from the Linux v5.18-rc1 tag.
This update should not impact any existing U-Boot functionality.
Signed-off-by: Samuel Holland <[email protected]>
|
|
Copy the devicetree source for the A10s/A13/GR8, A31(s), and A23/A33/R16
SoCs and all existing boards from the Linux v5.18-rc1 tag.
These changes are combined into one commit due to interdependencies:
- The unit addresses were removed from bitbanged I2C buses, which
drives a Kconfig default change. This affects sun5i-a13-utoo-p66.dts
and sun6i-a31-colombus.dts.
- The pinctrl nodes were renamed, including some used by the shared
header sunxi-reference-design-tablet.dtsi.
To maintain ABI compatibility with existing LTS kernels, one change
moving some IP blocks to the r_intc interrupt controller is excluded.
This effectively reverts Linux commits 994e5818392c and 9fdef3c3d8c2.
This commit renames the file sun8i-r16-nintendo-nes-classic-edition.dts
to sun8i-r16-nintendo-nes-classic.dts to match the Linux tree.
This commit also adds the following new board devicetrees:
- sun5i-a13-licheepi-one.dts
- sun5i-a13-pocketbook-touch-lux-3.dts
- sun5i-gr8-evb.dts
- sun8i-a23-ippo-q8h-v1.2.dts
- sun8i-a23-ippo-q8h-v5.dts
- sun8i-a33-et-q8-v1.6.dts
- sun8i-a33-ippo-q8h-v1.2.dts
- sun8i-r16-nintendo-super-nes-classic.dts
As with the other SoCs, updates of note are conversion of GPIO pull-up
from pinconf to GPIO flags and renaming the detection GPIO properties in
the USB PHY nodes.
Signed-off-by: Samuel Holland <[email protected]>
|
|
Copy the devicetree source for the A10 SoC and all existing boards
verbatim from the Linux v5.18-rc1 tag.
This commit also adds the following new board devicetree:
- sun4i-a10-topwise-a721.dts
While this update should not impact any existing U-Boot functionality,
the changes to the USB PHY detection GPIO properties are needed to
convert that driver to use the DM GPIO framework.
Signed-off-by: Samuel Holland <[email protected]>
|
|
Copy the devicetree source for the A20 SoC and all existing boards
verbatim from the Linux v5.18-rc1 tag.
This commit also adds the following new board devicetrees:
- sun7i-a20-haoyu-marsboard.dts
- sun7i-a20-linutronix-testbox-v2.dts
- sun7i-a20-olinuxino-lime-emmc.dts
This update includes changes to the USB PHY detection GPIO properties
which are needed to convert that driver to use the DM GPIO framework.
Signed-off-by: Samuel Holland <[email protected]>
[Andre: fix Mele M5 U-Boot only DT]
Reviewed-by: Andre Przywara <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
|
|
These files are not included anywhere and do not exist in the Linux
devicetree source.
Signed-off-by: Samuel Holland <[email protected]>
|
|
Some devicetree updates make use of newly-exposed clocks and resets.
To support that, copy the binding headers from the Linux v5.18-rc1 tag.
Signed-off-by: Samuel Holland <[email protected]>
|
|
|
|
Missing nodes may also be signaled via -ENODATA. We need to check for
that to prevent failing in non-usb3 setups.
Furthermore, dev.phy must be NULL'ed in case usb3-phy was not found.
Fixes: 142d50fbce7c ("usb: dwc3: Add support for usb3-phy PHY configuration")
Signed-off-by: Jan Kiszka <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-stm
- spi: fix busy bit check in stm32_qspi driver
- stm32mp15: configure Buck3 voltage per PMIC NVM on Avenger96 board
|
|
Before this commit device tree selection could rely solely on
differentiating the iMX6 processor variant Q and DL. After adding two new
carrier boards, the DRC02 and the picoITX, the interchangeability of SoMs
makes this approach infeasible.
It is now required to specify the carrier board (dhcom-drc02,
dhcom-picoitx or dhcom-pdk2) at compile time using
CONFIG_DEFAULT_DEVICETREE. The SoM is determined at runtime as before.
Signed-off-by: Philip Oberfichtner <[email protected]>
|
|
Add a u-boot dtsi for configuring the FEC node of the DH DRC02.
Reviewed-by: Marek Vasut <[email protected]>
Signed-off-by: Philip Oberfichtner <[email protected]>
|
|
Add a u-boot dtsi for configuring the FEC node of the DH picoITX.
Reviewed-by: Marek Vasut <[email protected]>
Signed-off-by: Philip Oberfichtner <[email protected]>
|
|
Firstly the FEC can now use the regulator reg_eth_vio from
imx6qdl-dhcom-som.dtsi instead of defining its own.
Secondly the &fec node is moved to the more generic SoM device tree
file, because it can be used by multiple boards.
Reviewed-by: Marek Vasut <[email protected]>
Signed-off-by: Philip Oberfichtner <[email protected]>
|
|
Use phy address from device tree instead of CONFIG_FEC_MXC_PHYADDR from
board header. This is required, because the DH picoITX and DRC02 boards
require different settings than PDK2. The corresponding 'phy-handle'
device tree properties are already there.
I tested this change on picoITX and DRC02, but on PDK2 it is untested.
Reviewed-by: Marek Vasut <[email protected]>
Signed-off-by: Philip Oberfichtner <[email protected]>
|
|
Migrate DH picoITX device trees from Linux commit 42226c989789
(tag v5.18-rc7). No changes have been made, the DTs are exact copies.
Furthermore add the DTB to dh_imx6_defconfig.
Reviewed-by: Marek Vasut <[email protected]>
Signed-off-by: Philip Oberfichtner <[email protected]>
|
|
Migrate DH DRC02 device trees from Linux commit 42226c989789
(tag v5.18-rc7). No changes have been made, the DTs are exact copies.
Furthermore add the DTB to dh_imx6_defconfig.
Reviewed-by: Marek Vasut <[email protected]>
Signed-off-by: Philip Oberfichtner <[email protected]>
|
|
In the DH electronics iMX6 board file fix the outdated eeprom path by
using a DT label instead.
The label has been newly created for all iMX6QDL DHCOM boards.
Reviewed-by: Marek Vasut <[email protected]>
Signed-off-by: Philip Oberfichtner <[email protected]>
|
|
Add PCA9450 regulator driver. This is complementary driver for the BUCKn
and LDOn regulators provided by the PCA9450 PMIC driver. Currently the
driver permits reading the settngs and configuring the BUCKn and LDOn
regulators.
Reviewed-by: Fabio Estevam <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
|
|
The upstream DT regulators node subnodes are named BUCKn and LDOn,
the downstream DT regulators node subnodes are named buckn and ldon,
add the upstream match.
Reviewed-by: Fabio Estevam <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
|
|
Enable CONFIG_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.
Signed-off-by: Peng Fan <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
Move the preloader_console_init() call after spl_early_init() to avoid
board hang in SPL.
While at it remove explicit in-code console/debug UART pinmuxing (uart1
and its pinmuxing are already marked as u-boot,dm-spl via device tree).
Fixes: 4551e1898769 ("configs: verdin-imx8mm: verdin-imx8mp: enable dm serial")
Signed-off-by: Marcel Ziswiler <[email protected]>
|
|
There is no reason for disabling I-cache and D-cache
in SPL.
Remove the unneeded CONFIG_SPL_SYS_ICACHE_OFF and
CONFIG_SPL_SYS_DCACHE_OFF options.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
There is no reason for disabling I-cache and D-cache
in SPL.
Remove the unneeded CONFIG_SPL_SYS_ICACHE_OFF and
CONFIG_SPL_SYS_DCACHE_OFF options.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
There is no reason for disabling I-cache and D-cache
in SPL.
Remove the unneeded CONFIG_SPL_SYS_ICACHE_OFF and
CONFIG_SPL_SYS_DCACHE_OFF options.
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Michael Trimarchi <[email protected]>
|
|
The Bosch ACC (Air Center Control) Board is based on the i.MX6D.
The device tree is copied from Linux, see [1]. The only difference
compared to the Linux DT is the removal of usbphynop properties. They are
defined in the Linux version of imx6qdl.dtsi, but not in the u-boot
version.
[1] Commit 6192cf8ac082 from
git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux.git
Signed-off-by: Philip Oberfichtner <[email protected]>
|
