| Age | Commit message (Collapse) | Author |
|---|
|
- NPCM7xx FIU SPI driver (Jim Liu)
- AT45DB641E dataflash (Luca Ellero)
|
|
Macro MVNETA_GMAC_FORCE_LINK_UP can be dropped from value assignment in
fixed link case, since it's value is written into the register later in
the function for link-down-to-link-up case. The value is written as
MVNETA_GMAC_FORCE_LINK_DOWN | MVNETA_GMAC_FORCE_LINK_PASS, and so the
macro definition can also be dropped.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Guard the code handling the fixed PHY case by
CONFIG_IS_ENABLED(PHY_FIXED).
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Since this member is checked only at two places drop it and inline it's
usage.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Write PHY address just before enabling HW polling of the PHY.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Stop parsing fixed-link in the MAC driver. Instead support only PHY mode
and let the fixed PHY driver handle the fixed-link case.
Enable CONFIG_PHY_FIXED for mvneta boards that need it: Turris Omnia and
ESPRESSObin.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
The CONFIG_* macros are reserved for Kconfig. This was probably done
when this driver was being imported from Linux. Rename the macro.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Drop checking for CONFIG_PHYLIB in mvneta, this is already done in
Kconfig.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Drop unnecessary space in mvneta_adjust_link().
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Use the bool type instead of int for status_change variable.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Drop one indentation level in the mvneta_adjust_link() function.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
The `ret` variable in mvneta_probe() is unused if DM_GPIO is disabled.
Since the variable is used only once after assigning value, we can
inline the usage and drop the variable.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
This MDIO bus is now handled by a proper mvmdio DM driver. Remove it
from mvneta.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
In order to be able to get rid of the non-DM MDIO bus registered in
mvneta driver, start using the DM registered one in Turris MOX board
code.
This also allows us to drop the hack introduced in MOX' -u-boot.dtsi
file.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Add helper to resolve PHY node from it's ofnode via DM MDIO subsystem.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
In order to be able to get rid of the non-DM MDIO bus registered in
mvneta driver, we need to stop using board_network_enable() and instead
use the DM registered MDIO device to configure switch in
last_stage_init().
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
We don't need to remember PHY address anymore, because since using DM
MDIO for connecting PHY, the address is parsed by mdio-uclass from
the ofnode.
But the driver uses a special value of the address to signal fixed link
usage.
Drop phyaddr add fixed_link in driver private structure. This simplifies
code a little.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Use the modern DM MDIO API for connecting PHY in the mvneta driver.
This requires enabling MVMDIO driver in several config files.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
In mvneta_adjust_link() we need to set MII_SPEED bit only if PHY reports
the speed at 100Mbps.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Drop .of_to_plat() from the mvneta driver and parse the two properties
in .probe().
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
This patch enables the Kconfig symbols needed for full ethernet support
on the NIC23. Additionally board specific setup is done, mostly GPIOs
related to SFP / GPIO configuration. With this, ethernet can be used on
this board. Here an example of a tftp load:
=> tftp ffffffff81000000 big
Using ethernet-mac-nexus@11800e2000000 device
TFTP from server 192.168.1.5; our IP address is 192.168.1.247
Filename 'big'.
Load address: 0xffffffff81000000
Loading: ################################################## 10 MiB
9.7 MiB/s
done
Bytes transferred = 10485760 (a00000 hex)
Signed-off-by: Stefan Roese <[email protected]>
|
|
This patch enables the Kconfig symbols needed for full ethernet support
on the EBB7304. Also the PHY autonegotiation timeout is increased, as
the default 5 seconds are sometime a bit short. With this, ethernet can
be used on this board. Here an example of a tftp load:
=> tftp ffffffff81000000 big
ethernet-mac-nexus@11800e0000000 Waiting for PHY auto negotiation to complete....... done
Using ethernet-mac-nexus@11800e0000000 device
TFTP from server 192.168.1.5; our IP address is 192.168.1.243
Filename 'big'.
Load address: 0xffffffff81000000
Loading: ################################################## 10 MiB
13.2 MiB/s
done
Bytes transferred = 10485760 (a00000 hex)
Signed-off-by: Stefan Roese <[email protected]>
|
|
This patchs adds the ethernet & MDIO driver for the MIPS Octeon II / III
SoC platform. Please note that these drivers are based on the 2013
U-Boot version from Marvell and make use of the platform supported
helper functions for the ethernet functionality, including stuff like
SFP handling.
Signed-off-by: Stefan Roese <[email protected]>
Cc: Ramon Fried <[email protected]>
Cc: Joe Hershberger <[email protected]>
|
|
Add the Octeon ethernet (BGX) and SFP DT nodes to the NIC23 dts file to
enable ethernet support on this board.
Signed-off-by: Stefan Roese <[email protected]>
|
|
Add the Octeon ethernet (BGX), SMI and PHY DT nodes to the EBB7304 dts
file to enable ethernet support on this board.
Signed-off-by: Stefan Roese <[email protected]>
|
|
Add the Octeon ethernet (BGX) and SMI DT node to the dtsi file.
Signed-off-by: Stefan Roese <[email protected]>
|
|
This patch moves CONFIG_SYS_INIT_SP_OFFSET to a higher address so that
it does not interfere with larger U-Boot images. This was noticed, while
adding network support to the EBB7304 board.
Signed-off-by: Stefan Roese <[email protected]>
|
|
Import configure_lmtdma_window from Marvell 2013 U-Boot as it's needed
for network functionality.
Signed-off-by: Stefan Roese <[email protected]>
|
|
Call octeon_bootmem_init() earlier in the boot process, so that this
bootmemory infrastructure is already initialized when e.g. the
networking support gets probed.
Signed-off-by: Stefan Roese <[email protected]>
|
|
This patch adds the newly added C files to the Makefile to enable
compilation. This is done in a separate step, to not introduce build
breakage while adding the single files with potentially missing
externals.
Signed-off-by: Stefan Roese <[email protected]>
|
|
This patch includes misc changes to already present Octeon MIPS C files
files, which are necessary for the upcoming ethernet support.
The changes are mostly:
- DM GPIO & I2C infrastructure
- Coding style cleanup while reworking of the code
Signed-off-by: Stefan Roese <[email protected]>
|
|
Import cvmx-range.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Import cvmx-qlm-tables.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Import cvmx-pko-internal-ports-range.c from 2013 U-Boot. It will be used
by the later added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Import cvmx-pko3-resources.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Import cvmx-pko3-compat.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Import cvmx-pko3-queue.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Import cvmx-pko3.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Import cvmx-pko.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Import cvmx-pki-resources.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Import cvmx-pki.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Import cvmx-ipd.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Import cvmx-ilk.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Import cvmx-global-resource.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Import cvmx-fpa-resource.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Import cvmx-fpa.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Import cvmx-fau-compat.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Import cvmx-cmd-queue.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Import cvmx-agl.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Import cvmx-helper-xaui.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
