| Age | Commit message (Collapse) | Author |
|---|
|
Add clock tables required for bing up ECSPI interfaces
Signed-off-by: Elmar Albert <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: uboot-imx <[email protected]>
Signed-off-by: Elmar Albert <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
Some globals where not properly initialized causing timeouts
as data packets where not immediately acknowledged.
Fixes: cc6b87ecaa96 ("net: tftp: Add client support for RFC 7440")
Signed-off-by: Arjan Minzinga Zijlstra <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
|
|
The IMX_FEC_BASE value is not used when CONFIG_DM_ETH is configured. So this
value can be removed.
Signed-off-by: Heiko Thiery <[email protected]>
Reviewed-By: Tim Harvey <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
Tested-by: Marcel Ziswiler <[email protected]>
|
|
Currently the space between kernel_addr_r and the fdt_addr_r is only 32MB.
To have enought space to load kernel images bigger than 32MB change the
variables to a feasible value.
The new environment variables layout is based on the scheme from
"include/configs/ti_armv7_common.h".
The CONFIG_SYS_LOAD_ADDR value is set to 0x42000000. With that we have
the same value as for the kernel_addr_r.
Signed-off-by: Heiko Thiery <[email protected]>
|
|
Add new board based on the Toradex Verdin iMX8M Mini SoM, the MX8Menlo.
The board is a compatible replacement for i.MX53 M53Menlo and features
USB, multiple UARTs, ethernet, LEDs, SD and eMMC.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Marcel Ziswiler <[email protected]>
Cc: Max Krummenacher <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
|
|
If FALCON mode is enabled we have a missing include in spl_start_uboot.
Signed-off-by: Jesse Taube <[email protected]>
|
|
The Linux kernel moved dt-bindings/pinctrl/pins-imxrt to the device tree
This patch move it in U-Boot as well.
Signed-off-by: Jesse Taube <[email protected]>
|
|
1M of heap is more than internal ram making booting without SDRAM not
possible now it is 256k
Signed-off-by: Jesse Taube <[email protected]>
|
|
In Linux IMX and IMXRT use the device tree to hold the anatop address.
The anatop is used in clock drivers as it controls the internal PLLs
This will move the macro from asm/arch-imxrt to the device tree.
This presumably should also be done with the other IMX boards as well.
Signed-off-by: Jesse Taube <[email protected]>
|
|
Add compatible string for i.MX8MP, which permits i.MX8MP to use
HS400ES mode, just like all the other i.MX8M.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Haibo Chen <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
|
|
The FlexSPI NOR boot offset does not require any special handling,
the image_offset is correct in either case (0x1000 for FlexSPI NOR
and 0x8000 for SD/eMMC) and the offset of u-boot.itb from the start
of flash.bin is always 0x58000 on MX8MN/MX8MP, which matches the
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512 - 0x8000 in case
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x300, which is always the
case on MX8MN/MX8MP.
The CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR is really overloaded in
case of the MX8MN/MX8MP, but fixing that needs additional plumbing.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
|
|
Add flexspi DT node matching Linux kernel as of commit
d7cd74466651e ("arm64: dts: imx8mp: Reorder flexspi clock-names entry")
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
|
|
The i.MX8M Mini and i.MX8M Plus flexspi IPs are compatible with one
another, however the linux kernel DT uses separate compatible string
for each SoC. Add the missing i.MX8MP compatible into this driver.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
|
|
The TI DP83867 phy has been replaced with the MaxLinear GPY111 phy due
to part availability.
Add support for it by adding LED config and dt-prop based internal delay
config tx-delay/rx-delay per PHY ID.
Signed-off-by: Tim Harvey <[email protected]>
Acked-by: Peng Fan <[email protected]>
|
|
Implement spl_board_loader_name to provide more meaningful device names
vs MMC1 and MMC2.
Signed-off-by: Tim Harvey <[email protected]>
|
|
The GW7902-C revision adds an ADC for the VDD_5P0 voltage rail.
Add register definitions for it.
Signed-off-by: Tim Harvey <[email protected]>
Acked-by: Peng Fan <[email protected]>
|
|
Update the 'boot_net' script to load the fdt with the kernel.
Signed-off-by: Tim Harvey <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
rcar3_salvator-x u-boot.img is very close to the 0x100000 size limit.
Enable linked time optimization (LTO).
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
Add support for Data Modul i.MX8M Mini eDM SBC board. This is an
evaluation board for various custom display units. Currently
supported are serial console, ethernet, eMMC, SD, SPI NOR,
USB host and USB OTG.
Reviewed-by: Fabio Estevam <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
|
|
Add redundand environment support as it is required
by SWUpdate.
While at it, also adjust the CONFIG_ENV_OFFSET to a more appropriate
larger offset as done on other i.MX8M defconfigs.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
The serial number is located at offset 0x14 of the EEPROM
under i2c0 bus at address 0x54.
To print the serial number in Linux:
SERNUM=$(cat /proc/device-tree/serial-number)
echo $SERNUM
Signed-off-by: Fabio Estevam <[email protected]>
|
|
Currently the eth0 MAC address is randomly assigned.
Retrieve the MAC address from EEPROM.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
Currently, the DDR type is retrieved by iteracting inside an array
of possible DDR types.
This may take saveral attempts, which slows the overall U-Boot process
and does not provide a good user experience:
U-Boot SPL 2021.07 (Feb 28 2022 - 06:39:32 +0000)
DDRINFO: Cfg attempt: [ 1/6 ]
DDRINFO(M): mr5-8 [ 0xff000010 ]
DDRINFO(T): mr5-8 [ 0x5000010 ]
resetting ...
U-Boot SPL 2021.07 (Feb 28 2022 - 06:39:32 +0000)
DDRINFO: Cfg attempt: [ 2/6 ]
DDRINFO(M): mr5-8 [ 0xff000010 ]
DDRINFO(T): mr5-8 [ 0x1061010 ]
resetting ...
U-Boot SPL 2021.07 (Feb 28 2022 - 06:39:32 +0000)
DDRINFO: Cfg attempt: [ 3/6 ]
DDRINFO(M): mr5-8 [ 0xff000010 ]
DDRINFO(T): mr5-8 [ 0xff000010 ]
Normal Boot
WDT: Not starting
Trying to boot from MMC2
NOTICE: BL31: v2.5(release):v2.5
NOTICE: BL31: Built : 07:12:44, Jan 24 2022
Improve the boot time by retrieving the correct DDR information from
the EEPROM:
U-Boot SPL 2022.04-rc4-00045-g6d02bc40d58c (Mar 19 2022 - 08:22:29 -0300)
DDRINFO(D): Kingston 4096G
DDRINFO(M): mr5-8 [ 0xff000010 ]
DDRINFO(E): mr5-8 [ 0xff000010 ]
Normal Boot
WDT: Started watchdog@30280000 with servicing (60s timeout)
Trying to boot from MMC2
NOTICE: BL31: v2.5(release):v2.5
NOTICE: BL31: Built : 22:28:11, Mar 15 2022
Based on the original code from Compulab's U-Boot.
Tested on a imx8mm-cl-iot-gate board populated with 4GB of RAM.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
imx8mm-cl-iot-gate supports multiple DDR sizes and models.
The DDR type can be retrieved from the EEPROM, so add SPL code
that can be used to get the DDR information.
Based on the original code from Compulab's U-Boot.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
Introduce BSH SystemMaster (SMM) S2 board family, which consists of:
iMX8MN SMM S2 and iMX8MN SMM S2 PRO boards.
Add support for iMX8MN BSH SMM S2 board:
- 256 MiB DDR3 RAM
- 512MiB Nand
- USBOTG1 peripheral - fastboot.
- 100Mbit Ethernet
Add support for iMX8MN BSH SMM S2 PRO board:
- 512 MiB DDR3 RAM
- 8 GiB eMMC
- USBOTG1 peripheral - fastboot.
- 100Mbit Ethernet
Signed-off-by: Ariel D'Alessandro <[email protected]>
Signed-off-by: Michael Trimarchi <[email protected]>
|
|
Add driver for the NXP TJA1100 and TJA1101 PHYs. These PHYs are special
BroadRReach 100BaseT1 PHYs used in automotive.
Signed-off-by: Michael Trimarchi <[email protected]>
Signed-off-by: Ariel D'Alessandro <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
|
|
Add read-modify-write unlocked accessor for accessing a PHY register.
Signed-off-by: Ariel D'Alessandro <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
|
|
This macro currently supports only one parameter. Based on Linux iopoll,
let's extend read_poll_timeout common API to allow multiple variable
parameters.
Signed-off-by: Ariel D'Alessandro <[email protected]>
|
|
This driver supports NXP C45 TJA11XX PHYs, but there're also other NXP
TJA11XX PHYs. Let's rename functions in this driver to be c45 variant
specific, so further drivers can be introduced adding support for NXP
TJA11XX PHYs.
Signed-off-by: Ariel D'Alessandro <[email protected]>
|
|
Add init_nand_clk to enable gpmi nand clock. Since i.MX8M not use CCF,
so we still use legacy mode to configure the clock.
Signed-off-by: Michael Trimarchi <[email protected]>
|
|
Add regs used by GPMI
Signed-off-by: Michael Trimarchi <[email protected]>
Signed-off-by: Ariel D'Alessandro <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
The power/bd71837.h should no longer be included, since V1.1 SoM
uses only the PCA9450 PMIC and the BD71837 support was removed.
Drop the header too.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Marcel Ziswiler <[email protected]>
Cc: Max Krummenacher <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Acked-by: Marcel Ziswiler <[email protected]>
|
|
Separe dm implementation from non dm implementation of pwm-imx
driver using CONFIG_DM_PWM
Signed-off-by: Tommaso Merciai <[email protected]>
|
|
Move pwm_imx_get_parms, pwm_id_to_reg functions into pwm-imx.c
and drop off pwm-imx-util.c
Signed-off-by: Tommaso Merciai <[email protected]>
|
|
Enable CONFIG_DM_SERIAL, and `dm tree` could show:
serial 1 [ ] serial_mxc | |-- serial@30a80000
Signed-off-by: Peng Fan <[email protected]>
|
|
Set the BYPASS ID SWAP bit (GPR10 bit 1).
The ID SWAP function randomly make TZASC grant non-secure access to
secure memory. TZASC ID SWAP should be bypassed by setting the bit
TZASC_ID_SWAP_BYPASS(bit 1) in IOMUX_GPR10 register.
Signed-off-by: Peng Fan <[email protected]>
|
|
Turns out on certain carrier boards (e.g. Iris V2) and under certain
circumstances (e.g. after a software reset) the SD card may have been
left in a strange state which later failed as follows:
Colibri iMX6ULL # mmc dev 0
Card did not respond to voltage select! : -110
Fix this as follows:
- Re-name the signaling voltage rail regulator from vmmc to vqmmc.
- Fix the name of the GPIO property to gpios.
- Specify 4-bit bus width, no write-protect capability and no 1.8
volt signaling voltage capability.
- Fix the clock vs. command pull-up vs. push-pull configuration.
Signed-off-by: Marcel Ziswiler <[email protected]>
|
|
Use the Micrel KSZ8xxx specific Ethernet PHY driver rather than the
generic one.
Signed-off-by: Marcel Ziswiler <[email protected]>
|
|
Fix NAND BCH geometry as otherwise the following errors are observed
upon boot:
...
Loading Environment from NAND... NAND read from offset 380000 failed -74
...
NAND read from offset 800 failed -74
...
ubi0 error: ubi_io_read: error -74 (ECC error) while reading 64 bytes
from PEB 0:0, read 64 bytes
...
Fixes: ed48490f8d3f
("mtd: gpmi: fix the bch setting backward compatible issue")
Signed-off-by: Marcel Ziswiler <[email protected]>
|
|
Add missing error message to blk_get_device_part_str.
Signed-off-by: Oleksii Bidnichenko <[email protected]>
Signed-off-by: Marcel Ziswiler <[email protected]>
|
|
Now that it is possible to use regulator-fixed-clock make use
of it. This makes U-Boot detect the PHY on first cold-boot.
This commit also adjusts the code in setup_fec and follows
how it is done in mx6ullevk.c
This commit also slows down the boot-process by about 150ms
as it now waits for the regulator-fixed-clock voltage that
drives the PHY to go up.
If you rely on very fast boot-speeds and don't need ethernet
for your boot-process you can safely revert the changes on
imx6ull-colibri.dtsi
Signed-off-by: Philippe Schenker <[email protected]>
Signed-off-by: Marcel Ziswiler <[email protected]>
|
|
This commit adds the possibility to choose the compatible
"regulator-fixed-clock" in devicetree.
This is a special case of regulator-fixed where a clock has to
be used to switch the regulator on and off.
Signed-off-by: Philippe Schenker <[email protected]>
Signed-off-by: Marcel Ziswiler <[email protected]>
|
|
Toradex uses the variable variant to distinguish between modules with
eMMC, NAND with wifi and NAND without wifi.
This variable is set on every boot. Set this variable also if we have a
NAND module without wifi to prevent issues.
Signed-off-by: Philippe Schenker <[email protected]>
Signed-off-by: Marcel Ziswiler <[email protected]>
|
|
U-Boot should never save the environment unasked.
This also avoids storing broken fdt_module to flash.
Signed-off-by: Denys Drozdov <[email protected]>
Signed-off-by: Marcel Ziswiler <[email protected]>
|
|
U-Boot should never save the environment unasked.
This also avoids storing broken ftd_file to eMMC.
Signed-off-by: Denys Drozdov <[email protected]>
Signed-off-by: Marcel Ziswiler <[email protected]>
|
|
Since we envision using overlays for display interfaces, the video=
settings within vidargs are obsolete. Remove these settings from the
U-Boot.
Signed-off-by: Oleksandr Suvorov <[email protected]>
Signed-off-by: Marcel Ziswiler <[email protected]>
|
|
All the other NAND-based boards have tdxargs specified for setting
manual kernel command-line arguments.
Signed-off-by: Philippe Schenker <[email protected]>
Signed-off-by: Marcel Ziswiler <[email protected]>
|
|
Enable driver model for serial.
Signed-off-by: Marcel Ziswiler <[email protected]>
|
|
Explicitly use the atf-bl31 type for the bl31.bin atf-blob. This uses
the path from the BL31 environment variable, if defined.
Signed-off-by: Marcel Ziswiler <[email protected]>
|
|
Rename board_early_init_f() to board_early_init(), since this function
has nothing to do with actual board_early_init_f() as used throughout
U-Boot. The board_early_init() is function local to this board used to
configure UART and WDT pinmux. Wrap init_uart_clk() into this function
so that early UART init would be all in one place. Turn the function
into __weak one, so it could be overridden in case custom carrier board
uses different UART or needs custom IOMUX settings.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Marcel Ziswiler <[email protected]>
Cc: Max Krummenacher <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
|
