| Age | Commit message (Collapse) | Author |
|---|
|
Add DT compatible string for PCA9450C PMIC. This is a variant of the
PCA9450 PMIC with 6 A dual-phase buck regulator and 3 A buck regulator,
and is software-wise compatible with the PCA9450B. This variant of the
PCA9450 is designed for use as companion PMIC for i.MX8MP.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
Reviewed-by: Jaehoon Chung <[email protected]>
|
|
The correct compatible string for i.MX8MP variant of DWC EQoS MAC
is "nxp,imx8mp-dwmac-eqos", use it. Drop the two current users of
the current wrong compatible string to avoid breaking them.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Marcel Ziswiler <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
Tested-by: Marcel Ziswiler <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
|
|
The Ethernet controller and PHY use the device tree info to
configure themselves, so it's not necessary to manually do it
in the board file. This permits the removal of a bunch of headers
as well.
Signed-off-by: Adam Ford <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
Acked-by: Peng Fan <[email protected]>
|
|
To be in sync with the linux devicetree add the disable-smarteee
property.
Signed-off-by: Heiko Thiery <[email protected]>
Tested-by: Marek Vasut <[email protected]> # 8MNANOD4-EVK
|
|
To be in sync with the linux devicetree change the 'phy-reset-gpios' in
the fec node to 'reset-gpios' in the phy node. The PHY reset will be
done by the eth-phy-uclass driver while probing the PHY. This is ok
since it is done before probing the fec.
Signed-off-by: Heiko Thiery <[email protected]>
Tested-by: Marek Vasut <[email protected]> # 8MNANOD4-EVK
Reviewed-by: Fabio Estevam <[email protected]>
|
|
With the correct settings described in the device-tree the PHY settings
in the board init are no longer required. The values are taken from the
linux device tree.
The PHY latency settings are derived from the phy-mode property and the
voltage seetings are done via the regulator.
Suggested-by: Michael Walle <[email protected]>
Signed-off-by: Heiko Thiery <[email protected]>
Tested-by: Marek Vasut <[email protected]> # 8MNANOD4-EVK
Reviewed-by: Fabio Estevam <[email protected]>
|
|
If we select DEVRES here then it breaks building an imx8m SPL without
DEVRES support.
Signed-off-by: Angus Ainslie <[email protected]>
|
|
In cpu_to_be32_array() and be32_to_cpu_array() we should not compare an int
counter to a size_t parameter. Correct the type of the counter. This
exists in upstream as b4c80629c5c9 ("include/linux/byteorder/generic.h:
fix index variables").
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
As in ASL case use same basic set of the inclusions.
Signed-off-by: Andy Shevchenko <[email protected]>
|
|
Enable LTO on mamoj to reduce SPL and uboot size. Tested with gcc
gcc-11.1.0
U-Boot 2022.04-rc4-00051-g17fc5facd0 (Mar 23 2022 - 16:43:43 +0100)
CPU: Freescale i.MX6DL rev1.3 996 MHz (running at 792 MHz)
CPU: Extended Commercial temperature grade (-20C to 105C) at 40C
Reset cause: POR
Model: BTicino i.MX6DL Mamoj board
DRAM: 512 MiB
Core: 29 devices, 12 uclasses, devicetree: separate
MMC: FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Net:
Error: ethernet@2188000 address not set.
No ethernet found.
Tested-by: Raffaele RECALCATI <[email protected]>
Signed-off-by: Michael Trimarchi <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
updated CAAM driver files maintainer.
Signed-off-by: Gaurav Jain <[email protected]>
|
|
removed sec_init() call from board files.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
device tree imported from linux kernel.
c500bee1c5b2 (tag: v5.14-rc4) Linux 5.14-rc4
Signed-off-by: Gaurav Jain <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
LS(1021/1012/1028/1043/1046/1088/2088), LX2160, LX2162
platforms are enabled with JR driver model.
removed sec_init() call from board files.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
Reviewed-by: Michael Walle <[email protected]>
|
|
LS(1021/1012/1028/1043/1046/1088/2088), LX2160 - updated device tree
Signed-off-by: Gaurav Jain <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
i.MX8(QM/QXP) - added support for JR driver model.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <[email protected]>
Signed-off-by: Horia Geantă <[email protected]>
Reviewed-by: Ye Li <[email protected]>
|
|
i.MX8(QM/QXP) - updated device tree for supporting DM in SPL.
disabled use of JR1 in SPL and uboot, as JR1 is reserved
for SECO FW.
Signed-off-by: Gaurav Jain <[email protected]>
Reviewed-by: Ye Li <[email protected]>
|
|
added crypto node in device tree.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <[email protected]>
Reviewed-by: Ye Li <[email protected]>
|
|
i.MX7D - added support for JR driver model.
removed sec_init() call, sec is initialized based on
job ring information processed from device tree.
Signed-off-by: Gaurav Jain <[email protected]>
Reviewed-by: Ye Li <[email protected]>
|
|
i.MX6,i.MX6SX,i.MX6UL - added support for JR driver model.
removed sec_init() call, sec is initialized based on
job ring information processed from device tree.
Signed-off-by: Gaurav Jain <[email protected]>
Reviewed-by: Ye Li <[email protected]>
|
|
Because we don't use SPL_DM on mx6sabresd and mx6sabreauto, so it is
unnecessary to have SPL DTB related configs and SPL_OF_CONTROL enabled.
Signed-off-by: Ye Li <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
Reviewed-by: Gaurav Jain <[email protected]>
|
|
i.MX8MM/MN/MP/MQ - added support for JR driver model.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <[email protected]>
Reviewed-by: Ye Li <[email protected]>
|
|
Signed-off-by: Gaurav Jain <[email protected]>
Reviewed-by: Ye Li <[email protected]>
|
|
added device tree support for job ring driver.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <[email protected]>
Reviewed-by: Ye Li <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
defconfig
If enable SPL_DM without SPL_OF_CONTROL,
build errors "undefined reference to fdt_get_resource",
is coming in function `caam_jr_probe'.
Added SPL_OF_CONTROL to remove the error.
Signed-off-by: Kshitiz Varshney <[email protected]>
|
|
We need to know where the typedef of 'ofnode' comes from.
Fixes: c86a4de8df61 ("mtd: Add flash_node in struct mtd_info")
Signed-off-by: Tom Rini <[email protected]>
|
|
- Assorted fixes/updates including K3-J721s2 timer dts fix, assorted
crypto improvements, led-pwm driver, improve handling of mtd
partitions, align mkimage hash output buffers and backport a UBIFS
bugfix from Linux.
|
|
Add AHCI PCI bindings for Marvell 88SE6121/45 SATA controllers.
The 88SE6121 controller is used, for example, in the Seagate Blackarmor NAS440 or the Iomega ix4-200d NAS.
As Pali Rohár explained [1], these controllers do not match the standard AHCI class code and therefore require an explizit PCI binding. The Linux kernel also uses this approach [2].
[1] https://lists.denx.de/pipermail/u-boot/2022-March/479197.html
[2] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/ata/ahci.c?h=v5.17#n557
Signed-off-by: Hajo Noerenberg <[email protected]>
Reviewed-by: Pali Rohár <[email protected]>
|
|
Backport commit 1cb51a15b576 ("ubifs: Fix journal replay wrt. xattr
nodes") from the Linux Kernel, which has the following Signed-off-by
line:
Signed-off-by: Richard Weinberger <[email protected]>
For U-Boot, after comapring with the upstream commit:
Signed-off-by: Tom Rini <[email protected]>
|
|
Hardware-accelerated hash functions require that the input and output
buffers be aligned to the minimum DMA alignment. memalign.h helpfully
provides a macro just for this purpose. It doesn't exist on the host,
but we don't need to be aligned there either.
Fixes: 5dfb521386 ("[new uImage] New uImage low-level API")
Signed-off-by: Sean Anderson <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Since the commit bfaa51dd4adf ("cmd: add serial console support
for the cls command") the cls command is not enough to clear the
video display when ANSI console is activated.
This patch clears the video device with the video_clear() API
before to display the bitmap used for the PXE background.
This patch avoids to display the LOGO, activated by default with
commit 7a8555d87136 ("video: Show the U-Boot logo by default").
Signed-off-by: Patrick Delaunay <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
In case mtd_info's dev field is not populated (raw nand's case),
use the flash_node new field which reference the DT flash node where
can be found "partitions" node with "fixed-partitions" compatible.
Signed-off-by: Patrice Chotard <[email protected]>
Cc: Farhan Ali <[email protected]>
Cc: Heinrich Schuchardt <[email protected]>
Cc: Jagan Teki <[email protected]>
Cc: Marek Behun <[email protected]>
Cc: Miquel Raynal <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Wolfgang Denk <[email protected]>
|
|
Currently, add_mtd_partitions_of() can be used only if dev field of
mtd_info struct is populated. It's the case, for example, for a spi nor
flash, which has a DT compatible "jedec,spi-nor" and an associated
device. mtd->dev is populated in spi_nor_scan().
But in case of a raw nand node, mtd_info's dev field can't be populated
as flash node has no compatible, so no associated device.
add_mtd_partitions_of() can't be used to parse "partitions" subnode.
To remove this constraint, add an ofnode field in mtd_info struct
which reference the DT flash node. This new field is populated by
nand_scan_tail(). This new field will be used by add_mtd_partitions_of()
to parse the flash node for "partitions" defined in DT.
Signed-off-by: Patrice Chotard <[email protected]>
Cc: Farhan Ali <[email protected]>
Cc: Heinrich Schuchardt <[email protected]>
Cc: Jagan Teki <[email protected]>
Cc: Marek Behun <[email protected]>
Cc: Miquel Raynal <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Wolfgang Denk <[email protected]>
|
|
When probing the LEDs, a default brightness is set based on settings
from the U-Boot device tree, i.e. the 'default-brightness' property
of the LED nodes. If that property is not present, the default
maximum brightness is set.
This should make sure the LED controller's registers affecting the
brightness are correctly initialized and should give a consistent
behaviour.
Signed-off-by: Paul HENRYS <[email protected]>
|
|
This was implemented in order to get dual-slot bootloader
partitions on the BeagleBone Black, whose MLO boots from
the first bootable partition: MLO chainloads u-boot in the
same way.
Signed-off-by: Jérôme Carretero <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Set digest_size SHA384 and SHA512 algorithms in pkcs7 and x509,
(not set by ported linux code, but needed by __UBOOT__ part).
EFI_CAPSULE_AUTHENTICATE doesn't select these algos but required for
correctness if certificates contain sha384WithRSAEncryption or
sha512WithRSAEncryption OIDs.
Signed-off-by: Dhananjay Phadke <[email protected]>
Reviewed-by: Ilias Apalodimas <[email protected]>
|
|
Add a driver which allows to use of LEDs connected
to PWM (Linux compatible).
MAINTAINERS: add i.vozvakhov as a maintainer of leds-pwm
C(required during new functionality adding).
Signed-off-by: Ivan Vozvakhov <[email protected]>
|
|
Modify function to support any salt length instead of max
length only. Function now detects salt length by parsing
the content of db buffer. Note that it works with (but is
not limited to) zero-length, digest-length and max-length
Signed-off-by: SESA644425 <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Prior to introduction of modifications in rsassa_pss functions
related to padding verification, doing a pass to reduce memory
consumption of function by replacing memory copies of parts of
const buffer by pointers to the original buffer (masked_db and
h are subparts of msg buffer which is declared const, salt is a
subpart of db which is a working buffer, unmodified after being
filled). New pointers scope is limited to the function where
they are declared (not returned to caller by any mean), zeroing
risk of memory fault related to the change.
Signed-off-by: SESA644425 <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Prior to introduction of modifications in rsassa_pss functions
related to padding verification, doing a pass to update
const-correctness in targeted functions to comply with
coding-rules and avoid const-cast
Signed-off-by: SESA644425 <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
MCU Timer0 runs at 250MHz, and the clock-frequency defined in DT appears
incorrect.
Without this delays in R5 SPL are 10x off.
Signed-off-by: Vignesh Raghavendra <[email protected]>
|
|
- Add support for OP-TEE providing an RNG to use, and enable on some
stm32mp15 configurations.
|
|
When the RNG device is secured with OP-TEE, it is only accessible with
the HWRNG TA, the CONFIG_RNG_OPTEE is needed for STM32MP15 targets
with OP-TEE support.
The probe of this RNG driver fails when the TA is not available in OP-TEE
and the previous driver can be used, as CONFIG_RNG_STM32MP1 is activated
and when the associated node is activated in the device tree with:
&rng1 {
status = "okay";
};
When the RNG is used in OP-TEE, this node should be deactivated in
the Linux and U-Boot device tree.
Signed-off-by: Patrick Delaunay <[email protected]>
|
|
In U-Boot, the discovery of TA based on its UUID on the TEE bus is
not supported.
This patch only binds the driver associated to the new supported
OP-TEE TA = TA_HWRNG when this driver is enable.
Signed-off-by: Patrick Delaunay <[email protected]>
|
|
Add driver for OP-TEE based Random Number Generator on ARM SoCs
where hardware entropy sources are not accessible to normal world
and the RNG service is provided by a HWRNG Trusted Application (TA).
This driver is based on the linux driver: char/hw_random/optee-rng.c
Signed-off-by: Patrick Delaunay <[email protected]>
|
|
To quote the author:
This series adds support for running valgrind against U-Boot's internal
malloc. This allows for much more useful reports to be generated.
Some example output of valgrind run against u-boot/master with this
branch applied may be found at [1]. Note that valgrind gives up around
acpi. This feature still needs a lot of work on suppressions/hints to
filter out the noise properly.
[1] https://gist.githubusercontent.com/Forty-Bot/199bf06f9cdd6871e54f8f484c16e111/raw/2a2f99108eef84b48e27a54332f3f71f4e2e5342/gistfile1.txt
|
|
This documents how to get more detailed results from valgrind made possible
by the last two commits.
Signed-off-by: Sean Anderson <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
This annotates malloc and friends so that valgrind can track the heap. To
do this, we need to follow a few rules:
* Call VALGRIND_MALLOCLIKE_BLOCK whenever we malloc something
* Call VALGRIND_FREELIKE_BLOCK whenever we free something (generally after
we have done our bookkeeping)
* Call VALGRIND_RESIZEINPLACE_BLOCK whenever we change the size of an
allocation. We don't record the original request size of a block, and
neither does valgrind. For this reason, we pretend that the old size of
the allocation was for 0 bytes. This marks the whole allocaton as
undefined, so in order to mark all bits correctly, we must make the whole
new allocation defined with VALGRIND_MAKE_MEM_DEFINED. This may cause us
to miss some invalid reads, but there is no way to detect these without
recording the original size of the allocation.
In addition to the above, dlmalloc itself tends to make a lot of accesses
which we know are safe, but which would be unsafe outside of dlmalloc. For
this reason, we provide a suppression file which ignores errors ocurring in
dlmalloc.c
Signed-off-by: Sean Anderson <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Valgrind uses magic code sequences to define an ABI that the client may use
to request behavior from the host. In particular, this may be used to
inform valgrind about custom allocators, such as the one used in U-Boot.
This adds headers defining these sequences to U-Boot. It also adds a config
option to disable emission of these sequences entirely, in the (likely)
event that the user does not wish to use valgrind. Note that this option is
called NVALGRIND upstream, but was renamed (and inverted) to
CONFIG_VALGRIND. Aside from this and the conversion of a few instances of
VALGRIND_DO_CLIENT_REQUEST_EXPR to STMT, these headers are unmodified.
These headers were copied from valgrind 3.16.1-4 as distributed in Arch
Linux. They are licensed with the bzip2 1.16 license. This appears to be a
BSD license with some clauses from Zlib.
Signed-off-by: Sean Anderson <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
i.MX8MQ use SYS_MALLOC_F_LEN 0x2000, not 0x10000. The OCRAM_S only has
32KB memory, use 0x10000 will make SPL not bootable.
Signed-off-by: Peng Fan <[email protected]>
Reviewed-by: Michael Trimarchi <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
