| Age | Commit message (Collapse) | Author |
|---|
|
Add definitions for a payload or 'self', which is like an unpacked ELF
file.
Signed-off-by: Simon Glass <[email protected]>
|
|
This should use a const pointer for the input stream. Fix this and also
add a proper comment.
Signed-off-by: Simon Glass <[email protected]>
|
|
We don't use an appended tree for sandbox and the required symbols are
not present. Add a condition to avoid a build error.
Signed-off-by: Simon Glass <[email protected]>
|
|
This may have different settings for SPL and TPL. Correct the condition.
Signed-off-by: Simon Glass <[email protected]>
|
|
If the buffer is empty and not allocated, then abuf_realloc() tries to
copy invalid data. This happens because an incorrect change to use
memdup() was added after the original code was written.
Signed-off-by: Simon Glass <[email protected]>
|
|
At present the header file defines this function in SPL but the file may
not actually be built. This causes a build error if the option is enabled.
Fix the condition in the header file.
Signed-off-by: Simon Glass <[email protected]>
|
|
The conversion to bintools broke the invocation of the utility, since
the arguments are not correct. Fix it.
Signed-off-by: Simon Glass <[email protected]>
|
|
|
|
- Add DM_PMIC support to TPS65217 and migrate some platforms to it.
- mkimage verification fixes
- DM rST fix, add missing flag when linking u-boot-elf.o
|
|
We use Sphinx style comments to describe functions.
Signed-off-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
If image backend provides verify_header callback then call it after writing
image to disk. This ensures that written image is correct.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
rockchip header_v2 do not have a spl_hdr, so remove the verify.
Signed-off-by: Yi Liu <[email protected]>
Signed-off-by: Kever Yang <[email protected]>
|
|
fix compile error when using a little-endian to build with configs:
sfr_nb4-ser_ram_defconfig
comtrend_wap5813n_ram_defconfig
comtrend_ar5387un_ram_defconfig
comtrend_ct5361_ram_defconfig
comtrend_vr3032u_ram_defconfig
comtrend_ar5315u_ram_defconfig
huawei_hg556a_ram_defconfig
netgear_dgnd3700v2_ram_defconfig
Signed-off-by: Du Huanpeng <[email protected]>
|
|
When trying to run qemu-riscv64_smode_defconfig with 32 harts booting
fails. The debug UART shows a message
alloc space exhausted
32 is the current maximum number of harts for machine virt in QEMU 7.0.
Raise the default for SYS_MALLOC_F_LEN to 16 KiB.
Move the setting to /Kconfig where we define SYS_MALLOC_F_LEN for
other architectures too.
Signed-off-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Rick Chen <[email protected]>
|
|
Let CONFIG_TARGET_QEMU_VIRT imply CONFIG_CMD_SBI.
The sbi command provides detailed information about the SBI.
It is useful to test the discovery of extensions.
Signed-off-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
Let the sbi command display:
* machine vendor ID
* machine architecture ID
* machine implementation ID
With this patch the output for the HiFive Unmatched looks like
=> sbi
SBI 0.3
OpenSBI 0.9
Machine:
Vendor ID 489
Architecture ID 8000000000000007
Implementation ID 20181004
Extensions:
sbi_set_timer
sbi_console_putchar
sbi_console_getchar
sbi_clear_ipi
sbi_send_ipi
sbi_remote_fence_i
sbi_remote_sfence_vma
sbi_remote_sfence_vma_asid
sbi_shutdown
SBI Base Functionality
Timer Extension
IPI Extension
RFENCE Extension
Hart State Management Extension
System Reset Extension
Signed-off-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Sean Anderson <[email protected]>
|
|
Provide library functions to read:
* machine vendor ID
* machine architecture ID
* machine implementation ID
Signed-off-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Sean Anderson <[email protected]>
|
|
Version 1.0-rc3 of the RISC-V Supervisor Binary Interface Specification
has added the Performance Monitoring Unit Extension.
The sbi command should be able to detect it.
Signed-off-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
The tps65217 PMIC driver is used with am335x SoC based designs.
It is used in the SPL (MLO) as well, so the DM conversion only is
for u-boot proper.
This driver only allows simple reading/writing/dumping of the content
of its registers and requires the DM_I2C for proper operation.
Signed-off-by: Lukasz Majewski <[email protected]>
Reviewed-by: Jaehoon Chung <[email protected]>
|
|
Up till now the CONFIG_POWER_TPS65217 has been defined in several header
files for am335x SoC.
This patch renames it to CONFIG_PMIC_TPS65217, which better reflects the
role of this IC circuit.
Moreover, new CONFIG_PMIC_TPS65217 has been introduced in Kconfig
to be used with boards, which both support DM_PMIC and DM_I2C.
Signed-off-by: Lukasz Majewski <[email protected]>
Reviewed-by: Jaehoon Chung <[email protected]>
[trini: Migrate all other platforms as well]
Signed-off-by: Tom Rini <[email protected]>
|
|
- Updates for exynos78x0 and TI K3 platforms
|
|
https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.07-rc1 v2
xilinx:
- Allow booting bigger kernels till 100MB
zynqmp:
- DT updates (reset IDs)
- Remove unneeded low level uart initialization from psu_init*
- Enable PWM features
- Add support for 1EG device
serial_zynq:
- Change fifo behavior in DEBUG mode
zynq_sdhci:
- Fix BASECLK setting calculation
clk_zynqmp:
- Add support for showing video clock
gpio:
- Update slg driver to handle DT flags
net:
- Update ethernet_id code to support also DM_ETH_PHY
- Add support for DM_ETH_PHY in gem driver
- Enable dynamic mode for SGMII config in gem driver
pwm:
- Add driver for cadence PWM
versal:
- Add support for reserved memory
firmware:
- Handle PD enabling for SPL
- Add support for IOUSLCR SGMII configurations
include:
- Sync phy.h with Linux
- Update xilinx power domain dt binding headers
|
|
Add support for SGMII dynamic configuration which will takes care of
configuring SGMII in the GEM secure (GEM_CLK_CTRL) configuration
register.
Signed-off-by: T Karthik Reddy <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/a8915186e44015959978d080a31de652f544cd4a.1648631275.git.michal.simek@xilinx.com
|
|
Add zynqmp_pm_set_gem_config() api to configure GEM secure registers.
Signed-off-by: T Karthik Reddy <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/f69e32355c6a6be7d2780663353c52757530207d.1648631275.git.michal.simek@xilinx.com
|
|
In current slg7xl45106 gpio driver xlate() function we are not updating
gpio flags from DT. Read the given flag from DT and update the gpio desc
flags variable with required gpio direction state.
Signed-off-by: T Karthik Reddy <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/a8d7b4799337bd99f61ace509889f02b192a9414.1648631275.git.michal.simek@xilinx.com
|
|
As we are not reading the PHY address in case of CONFIG_ETH_PHY in plat
function, phy address always prints as -1. So move the ethernet info
print statement to probe function, to display proper phy address.
Signed-off-by: T Karthik Reddy <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/f6efc6719d767b1bebe65987c22c6d52329f4225.1648631275.git.michal.simek@xilinx.com
|
|
If DM_ETH_PHY config is enabled PHY gpio reset is taken care by the
eth-phy-uclass driver, so use the PHY gpio reset functionality from
ethernet_id file when this config is disabled to reset the PHY.
Use debug() print instead of dev_err() to avoid warning incase if phy-id
compatible string is not present.
Signed-off-by: T Karthik Reddy <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/4d0fd3f9f886c1d943776025e5efb5438b0eb389.1648631275.git.michal.simek@xilinx.com
|
|
CONFIG_ETH_PHY enables support to utilize generic ethernet phy
framework. Though if ethernet PHY node is in other ethernet node, it
will use shared MDIO to access the PHY of other ethernet.
Signed-off-by: Michal Simek <[email protected]>
Signed-off-by: T Karthik Reddy <[email protected]>
Link: https://lore.kernel.org/r/337b1a38ba36cde1951739af62fb3d2736d97f53.1648631275.git.michal.simek@xilinx.com
|
|
There are some new power domain IDs which are used in Linux kernel that's
why add them here too.
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/e6092e1d3766c0ac11bf620820739c93ab677a85.1648626981.git.michal.simek@xilinx.com
|
|
Add ID code for 1eg device.
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/5b6c9f6a25bba076f304bc4699f6f676a929a683.1648619516.git.michal.simek@xilinx.com
|
|
While creating a phy device using phy_device_create(), we need to
provide a valid phyaddr instead of 0 causing phy address being
registered as 0 with mdio bus and shows mdio phy list as below
ZynqMP> mdio list
eth0:
0 - TI DP83867 <--> ethernet@ff0b0000
eth1:
0 - TI DP83867 <--> ethernet@ff0c0000
Also PHY soft reset is being requested on 0 instead of valid
address causing "PHY reset timed out" error.
So add phyaddr argument to phy_connect_phy_id() and to its prototype
to create phy device with valid phyaddress.
Fixes: a744a284e354 ("net: phy: Add support for ethernet-phy-id with gpio reset")
Signed-off-by: T Karthik Reddy <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
Link: https://lore.kernel.org/r/fe35fddb9faa5af577ffdfabaec6879c935a30f8.1648562755.git.michal.simek@xilinx.com
|
|
Add support for getting rate for DP audio and video clocks.
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/8792efe1fd9715f7c8a2e1e24f0454fb5b25d833.1648552434.git.michal.simek@xilinx.com
|
|
A big part is the DM pinctrl driver, which allows us to get rid of quite
some custom pinmux code and make the whole port much more robust. Many
thanks to Samuel for that nice contribution! There are some more or less
cosmetic warnings about missing clocks right now, I will send the trivial
fixes for that later.
Another big chunk is the mkimage upgrade, which adds RISC-V and TOC0
(secure images) support. Both features are unused at the moment, but I
have an always-secure board that will use that once the DT lands in the
kernel.
On top of those big things we have some smaller fixes, improving the
I2C DM support, fixing some H6/H616 early clock setup and improving the
eMMC boot partition support.
The gitlab CI completed successfully, including the build test for all
161 sunxi boards. I also boot tested on a A64, A20, H3, H6, and F1C100
board. USB, SD card, eMMC, and Ethernet all work there (where applicable).
|
|
Recently big Linux kernels can have more then 60MB that's why increase this
limit to also cover these large kernels.
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/f52f7c8ea419d69b248ba1460a96d1635194e128.1648551279.git.michal.simek@xilinx.com
|
|
Now that the SPL can safely detect whether it was loaded from an eMMC
boot partition or the normal user data partition, let's enable this
feature on some boards that feature eMMC storage.
That covers the boards where I could test this on, and allows the same
build to be written to an SD card, eMMC user partition, eMMC boot
partition, or into SPI NOR flash.
Signed-off-by: Andre Przywara <[email protected]>
|
|
When the Allwinner BROM loads the SPL from an eMMC boot partition, it
sets the boot source byte to the same value as when booting from the
user data partition. This prevents us from determining the boot source
to load U-Boot proper from the proper partition for sure.
The generic SPL MMC code already looks at the enabled boot partition
number, to load U-Boot proper from the same partition, but this fails
if there is nothing bootable in this partition, as the BROM then
silently falls back to the user data partition, which the SPL misses.
To learn about the actual boot source anyway, we repeat the algorithm
the BROM used to select the boot partition in the first place:
- Test EXT_CSD[179] to check if an eMMC boot partition is enabled.
- Test EXT_CSD[177] to check for valid MMC interface settings.
- Check if BOOT_ACK is enabled.
- Check the beginning of the first sector for a valid eGON signature.
- Load the whole SPL.
- Recalculate the checksum to verify the SPL is valid.
If one of those steps fails, we bail out and continue loading from the
user data partition. Otherwise we load from the selected boot partition.
Since the boot source is needed twice in the boot process, we cache the
result of this test to avoid doing this costly test multiple times.
This allows the very same image file to be put onto an SD card, into the
eMMC user data partition or into the eMMC boot partition, and safely
loads the whole of U-Boot from there.
Signed-off-by: Andre Przywara <[email protected]>
|
|
Signed-off-by: Christian Gmeiner <[email protected]>
|
|
Makes it possible to use 16-bit DDR memory.
Signed-off-by: Dominic Rath <[email protected]>
Signed-off-by: Christian Gmeiner <[email protected]>
|
|
Add CONFIG_NR_DRAM_BANKS from am64x_evm_a53_defconfig as this is needed
to calculate the size of DDR that is available.
Signed-off-by: Dave Gerlach <[email protected]>
|
|
Add 'ss_cfg' memory region for memorycontroller node which is required
to enable ECC.
Signed-off-by: Dave Gerlach <[email protected]>
|
|
Call into k3-ddrss driver to fixup device tree and resize the available
amount of DDR if ECC is enabled.
A second fixup is required from A53 SPL to take the fixup as done from
R5 SPL and apply it to DT passed to A53 U-boot, which in turn passes
this to the OS.
Signed-off-by: Dave Gerlach <[email protected]>
|
|
Introduce ECC Functionality for full memory space as implemented in the
DDRSS. The following is done to accomplish this:
* Introduce a memory region "ss" to allow dt to provide DDRSS region,
which is not the same as "ctl" which is the controller region.
* Introduce a "ti,ecc-enable" flag which allows a memorycontroller
instance to enable ecc.
* Introduce functionality to properly program the DDRSS registers to
enable ECC for the full DDR memory space if enabled with above flag.
* Expose a k3_ddrss_ddr_fdt_fixup call to allow fixup of fdt blob to
account from DDR memory that must be reserved for ECC operation.
Signed-off-by: Dave Gerlach <[email protected]>
|
|
The current address being read from dt actually represents the ddrss_ctl
memory region, while ddrss_ss region is something else. Introduce
ddrss_ctl_regs and use it to free up ddrss_ss_regs for its proper
purpose later so that we can avoid confusion.
Signed-off-by: Dave Gerlach <[email protected]>
|
|
Add DT binding documentation for enabling ECC in the DDR sub system present
on AM64 device.
Signed-off-by: Dave Gerlach <[email protected]>
|
|
Use the appropriate fdtdec_setup_mem_size_base and
fdtdec_setup_bank_size calls in dram_init and dram_bank_init to pull
these values from DT, where they are already available, instead of
hardcoding them.
Signed-off-by: Dave Gerlach <[email protected]>
|
|
Mark the memory node with u-boot,dm-spl so we can use it from early SPL.
Signed-off-by: Dave Gerlach <[email protected]>
|
|
Timer0 runs at 200MHz,and the clock-frequency defined in DT is
incorrect. Fix it.
Signed-off-by: Vignesh Raghavendra <[email protected]>
Reviewed-By: Nishanth Menon <[email protected]>
|
|
On arm64 systems, recommendation is to use per-cpu timer for time
keeping. Currently AM64 ends up using DM timer as tick timer as driver
is enabled in the config. Drop OMAP DM Timer related configs, this will
switch to using armv8 per-cpu timer as tick timer for A53 SPL/U-Boot.
Signed-off-by: Vignesh Raghavendra <[email protected]>
Reviewed-By: Nishanth Menon <[email protected]>
|
|
Enable ESM driver for AM64x R5 SPL/u-boot builds.
Signed-off-by: Hari Nagalla <[email protected]>
Reviewed-by: Christian Gmeiner <[email protected]>
|
|
On AM64x devices, it is possible to route Main ESM0 error events to MCU
ESM. MCU ESM high error output can trigger the reset logic to reset the
device. So, for these devices we expect two ESM device nodes in the
device tree, one for Main ESM and the another MCU ESM in the device tree.
When these ESM device nodes are properly configired it is possible to
route the Main RTI0 WWDT output to the MCU ESM high output through Main
ESM and trigger a device reset when
CTRLMMR_MCU_RST_CTRL:MCU_ESM_ERROR_RESET_EN_Z is set to '0'.
On K3 AM64x devices, the R5 SPL u-boot handles the ESM device node
configurations.
Signed-off-by: Hari Nagalla <[email protected]>
Reviewed-by: Christian Gmeiner <[email protected]>
|
