| Age | Commit message (Collapse) | Author |
|---|
|
This converts the following to Kconfig:
CONFIG_CLOCKS
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_CLOCK_SYNTHESIZER
Signed-off-by: Tom Rini <[email protected]>
|
|
We only set one of these values ever at this point, so remove dead code.
Cc: Minkyu Kang <[email protected]>
Cc: Jaehoon Chung <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Minkyu Kang <[email protected]>
Reviewed-by: Jaehoon Chung <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_SYS_USE_NORFLASH
CONFIG_SYS_USE_BOOT_NORFLASH
Signed-off-by: Tom Rini <[email protected]>
|
|
There are a handful of variants around CONFIG_SYS_USE_DATAFLASH and none
of them now control anything further within their board config.h files,
so remove these from CONFIG_SYS_EXTRA_OPTIONS and then remove the empty
blocks in the board config.h files. In a few places further clean up
related logic.
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_SDCARD
CONFIG_SPIFLASH
Signed-off-by: Tom Rini <[email protected]>
|
|
CONFIG_QSPI is not used in the code, drop this.
Signed-off-by: Tom Rini <[email protected]>
|
|
Move this symbol to the board Kconfig file.
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_LPUART
CONFIG_LPUART_32B_REG
And note that CONFIG_LPUART_32B_REG is unused in code.
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_LSCHLV2
CONFIG_LSXHL
Cc: Michael Walle <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Michael Walle <[email protected]>
|
|
This CONFIG option is used in one place, so pick a more direct name and
migrate to Kconfig. Rework the code slightly.
Cc: Priyanka Jain <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_KM_COGE5UN
CONFIG_KM_KIRKWOOD_128M16
CONFIG_KM_KIRKWOOD
CONFIG_KM_KIRKWOOD_PCI
CONFIG_KM_NUSA
CONFIG_KM_SUSE2
Cc: Holger Brunck <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Holger Brunck <[email protected]>
|
|
The only usage of CONFIG_KMTEGR1 can be replaced by
CONFIG_TARGET_KMTEGR1 so do so and remove this other symbol.
Cc: Holger Brunck <[email protected]>
Cc: Heiko Schocher <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
Reviewed-by: Holger Brunck <[email protected]>
|
|
The way board/keymile/Kconfig is written protects the options there from
being parsed on non-keymile platforms. We cannot however safely source
this file from multiple locations. This does not manifest as a problem
currently as there are no choice statements inside of this file (nor the
sub-Kconfig files it sources). However, moving some target selection to
one of these files exposes the underlying problem. Rework things so
that we have this file sourced in arch/Kconfig.
Cc: Holger Brunck <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Holger Brunck <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_EMMC_BOOT
CONFIG_MAC_ADDR_IN_SPIFLASH
CONFIG_NAND_BOOT
CONFIG_SPL_FSL_PBL
CONFIG_SYS_FSL_DDR4
In this case we re-sync options that had been set in
CONFIG_SYS_EXTRA_OPTIONS but should not have been as they have proper
entries.
Signed-off-by: Tom Rini <[email protected]>
|
|
This was only setting values not referenced in the code so remove it.
Cc: Fabio Estevam <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
This platform is the only one to set these options, so define them in
the board Kconfig file.
Cc: Angelo Dureghello <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_MCFRTC
CONFIG_SYS_MCFRTC_BASE
While at it, remove '#undef RTC_DEBUG' from these config files.
Signed-off-by: Tom Rini <[email protected]>
|
|
This is not referenced anywhere, remove it.
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_MCFTMR
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_CF_DSPI
Signed-off-by: Tom Rini <[email protected]>
|
|
This seems to be unused in the code, remove it.
Cc: Eugen Hristev <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Both of these variables are used in a few hard-coded ways to set some
string values or print something to the user. In almost all cases, it's
just as useful to hard-code the value used. The exception here is
printing something closer to correct board name for p1_p2_rdb machines.
This can be done using something from the device tree, but for now
hard-code a non-CONFIG based value instead.
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_BITBANGMII_MULTI
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_BCM2835_GPIO
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_BOOTM_NETBSD
CONFIG_BOOTM_RTEMS
CONFIG_DESIGNWARE_WATCHDOG
CONFIG_DISPLAY_CPUINFO
CONFIG_DM_ETH
CONFIG_DM_MMC
CONFIG_DM_REGULATOR
CONFIG_DM_SPI
CONFIG_DM_SPI_FLASH
CONFIG_ISO_PARTITION
CONFIG_OF_SEPARATE
CONFIG_SPI_FLASH_WINBOND
CONFIG_SPL_ETH
CONFIG_TIMER
CONFIG_USB_DWC3
CONFIG_USB_DWC3_GADGET
CONFIG_USB_DWC3_OMAP
CONFIG_USB_DWC3_PHY_OMAP
CONFIG_USB_EHCI_TEGRA
CONFIG_USB_GADGET_DOWNLOAD
CONFIG_USB_GADGET_DUALSPEED
CONFIG_USB_GADGET_MANUFACTURER
CONFIG_USB_GADGET_PRODUCT_NUM
CONFIG_USB_GADGET_VBUS_DRAW
CONFIG_USB_GADGET_VENDOR_NUM
This catches a number of cases where board config files were #undef
various CONFIG options when building SPL, and that doesn't work. Clean
up the related comments as well.
Signed-off-by: Tom Rini <[email protected]>
|
|
We need to check for config header files that #undef migrated symbols as
well.
Signed-off-by: Tom Rini <[email protected]>
|
|
At this point DM and OF_CONTROL are used to configure how the USB ports
are enabled, with the exception of in SPL and no SPL_OF_CONTROL. Remove
a bunch of now unused logic to simplify the code.
Signed-off-by: Tom Rini <[email protected]>
|
|
colibri-imx6ull ethernet device is fec2, while the optional secondary
ethernet is fec1, update the ethernet aliases in the .dts file so that
ethaddr is set to fec2 and eth1addr to fec1.
Without this change the ethernet interfaces have a different
mac address between Linux and U-Boot.
Signed-off-by: Francesco Dolcini <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
Enable CONFIG_ATMEL_TCB_TIMER and disable CONFIG_ATMEL_PIT_TIMER.
This will allow using the TCB timer instead of the PIT one when running
under OP-TEE.
Reviewed-by: Claudiu Beznea <[email protected]>
Signed-off-by: Clément Léger <[email protected]>
|
|
In order to use the TCB early in boot and in the SPL, add
u-boot,dm-pre-reloc property for the TCB and the clock that is used by
the driver (tcb0_clk).
Signed-off-by: Clément Léger <[email protected]>
|
|
Add the device-tree node to describe the TCB timer.
Signed-off-by: Clément Léger <[email protected]>
|
|
When using interrupts property, a global interrupt controller needs to
be added to avoid warnings when compiling device-tree:
arch/arm/dts/at91-sama5d2_xplained.dtb: Warning (interrupts_property):
/ahb/apb/timer@f800c000: Missing interrupt-parent
Add AIC node as the sama5d2 global interrupt controller.
Signed-off-by: Clément Léger <[email protected]>
|
|
Add a driver for the timer counter block that can be found on sama5d2.
This driver will be used when booting under OP-TEE since the pit timer
which is part of the SYSC is secured. Channel 1 & 2 are configured to
be chained together which allows to have a 64bits counter.
Reviewed-by: Claudiu Beznea <[email protected]>
Signed-off-by: Clément Léger <[email protected]>
|
|
Align the DT for sama7g5 SoC and sama7g5 EK board with Linux devicetree
in version 5.18.
Some things remain still different, due to some things yet unimplemented in
certain drivers. These include in PMC, pinctrl, and others.
Signed-off-by: Eugen Hristev <[email protected]>
Reviewed-by: Tudor Ambarus <[email protected]>
|
|
In Linux this DT file is named at91-sama7g5ek.dts. Rename it accordingly.
Signed-off-by: Eugen Hristev <[email protected]>
Reviewed-by: Tudor Ambarus <[email protected]>
|
|
Set blue led on at boot time in order to highlight that u-boot is loaded.
This is done for all sama5d2 based boards which contain an RGB led.
Signed-off-by: Mihai Sain <[email protected]>
|
|
sama7g5 and other SoCs (sama5d3, sam9x60) define in the Reset Controller
a RSTC_CR.EXTRST bit that asserts the nrst_out pin which resets external
devices.
This is particular useful for external devices that are configured in
stateful modes which can not be undone without reconfiguring the device
or without resetting the device. An example is an SPI NOR flash that is
configured in octal mode. The do_reset u-boot cmd does not call any
driver's remove method, but merely resets the CPU. As the code was, this
left the flash in octal mode, being impossible for the first stage boot
loaders to recover/identify the flash after a "software reset".
RSTC_CR.EXTRST comes in handy here, as it can be set at "software reset"
to assert low the nrst_out pin during a time defined by the RSTC_MR.ERSTL
field and reset the external devices (including the SPI NOR flash in the
example).
nrst_out is always asserted at "user reset" and it resets the external
devices correctly. Asserting nrst_out at "software reset" should behave
in a similar way. The only difference that I could find between the two
types of resets in regards to the nrst_out signal, is that at "user reset"
timing diagram the "Processor and Peripherals Reset Line" rises after six
MD_SLCK cycles after the nrst_out line rose, while at the "software reset"
timing diagram the "Processor and Peripherals Reset Line" is active for
3 MD_SLCK cycles + 2 MCK cycles. In other words, in the "software reset"
case the nrst_out signal can be active for a longer period of time than the
"Processor and Peripherals Reset Line" active time, depending on the
RSTC_MR.ERSTL value.
Using the default value (zero) for RSTC_MR.ERSTL, worked just fine for the
sama7g5 case. Tested QSPI0 and GMAC0/GMAC1 on sama7g5ek rev 4 after a
software reset with RSTC_CR.EXTRST=1 and RSTC_MR.ERSTL=0.
Signed-off-by: Tudor Ambarus <[email protected]>
|
|
Convert AT91RESET_EXTRST to Kconfig for easier integration. The symbol is
not configurable from menuconfig, it will be automatically selected by SoCs
that select it explicitly via the "select" directive.
AT91RESET_EXTRST sets the Reset Controller's RSTC_CR.EXTRST bit which
asserts the nrst_out pin that resets external devices.
Signed-off-by: Tudor Ambarus <[email protected]>
|
|
sama5d2 contains in its ROM memory BCH code tables for NAND Flash ECC
correction. Enable the use of the GF tables defined in ROM. This should
speed up the boot process, as the tables are no longer constructed at
runtime. Tested with sama5d2-ptc-ek.
Reported-by: David Mosberger-Tang <[email protected]>
Signed-off-by: Tudor Ambarus <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-04-rc6
Documentation:
* Move VxWorks and Plan 9 to HTML documentation
* Move all command man-pages to a separate directory
Test:
* Fix pylint errors
UEFI
* Fix build flags for initrddump.efi
QEMU
* Remove unused function to get RNG device
|
|
If include/generated/environment.h exists (perhaps leftover from a build
of another board) it is used, even if the board currently being built does
not have a text environment.
This causes a build error. Fix it by emptying the file if it should not be
there.
Fixes: https://source.denx.de/u-boot/u-boot/-/issues/9
Signed-off-by: Simon Glass <[email protected]>
Reported-by: Sean Anderson <[email protected]>
Tested-by: Sean Anderson <[email protected]>
|
|
To quote the author:
This series adds a stage pre-load before launching an image. This stage
is used to read a header before the image and this header contains the
signature of the full image. So u-boot may check the full image before
using any data of the image.
The support of this header is added to binman, and a command verify
checks the signature of a blob and set the u-boot env variable
"loadaddr_verified" to the beginning of the "real" image.
The support of this header is only added to binman, but it may also be
added to mkimage.
|
|
Add a subcommand preload to bootm that execute the preload
stage on the image. Right now, it checks the signature
of the image with the pre-load header. If the check
succeed, the u-boot env variable 'loadaddr_verified'
is set to the address of the image (without the header).
It allows to run such commands:
tftp script.img && bootm preload $loadaddr && source $loadaddr_verified
Signed-off-by: Philippe Reynes <[email protected]>
|
|
Adds test units for the pre-load header signature.
Signed-off-by: Philippe Reynes <[email protected]>
|
|
Enable the support of stage pre-load in bootm.
For the moment, this stage allow to verify the
signature of the full image with a header.
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Philippe Reynes <[email protected]>
|
|
Adds the support of the pre-load header with the image signature
to binman.
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Philippe Reynes <[email protected]>
|
|
Set the variable pre-load-key-path with the shell variable
PRE_LOAD_KEY_PATH that contain the keys path (used for signature).
This variable pre-load-key-path is provided to binman.
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Philippe Reynes <[email protected]>
|
|
This commit enhances mkimage to update the node
/image/pre-load/sig with the public key.
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Philippe Reynes <[email protected]>
|
|
Add the support of image pre load in spl or tpl
when loading an image from ram.
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Philippe Reynes <[email protected]>
|
