| Age | Commit message (Collapse) | Author |
|---|
|
The function was missing from exports, even though it loooks like the
intent of the implementation in sscanf.c was to have it exported.
Signed-off-by: Samuel Dionne-Riel <[email protected]>
Cc: Simon Glass <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Let the check pass when patches have these patterns in their context.
Signed-off-by: Hou Zhiqiang <[email protected]>
|
|
Calling 'nvme scan' followed by 'nvme detail' crashes U-Boot on Turris
Omnia with the following error:
undefined instruction
pc : [<0a000000>] lr : [<7ff80bfc>]
reloc pc : [<8a8c0000>] lr : [<00840bfc>]
sp : 7fb2b908 ip : 0000002a fp : 02000000
r10: 04000000 r9 : 7fb2fed0 r8 : e1000000
r7 : 0c000000 r6 : 03000000 r5 : 06000000 r4 : 01000000
r3 : 7fb30928 r2 : 7fb30928 r1 : 00000000 r0 : 00000000
Flags: nZCv IRQs off FIQs off Mode SVC_32
Code: 0f0fb4f0 0f0fb4f0 0f0fb4f0 0f0fb4f0 (f0f04b0f)
Resetting CPU ...
This happens when nvme_print_info() tries to return to the caller. It
looks like this error is caused by trying to allocate 8 KiB of memory
on the stack by the two uses of ALLOC_CACHE_ALIGN_BUFFER().
Use malloc_cache_aligned() to allocate this memory dynamically instead.
This fixes 'nvme detail' on Turris Omnia.
Note that similar change was applied to file drivers/nvme/nvme.c in past by
commit 2f83481dff9c ("nvme: use page-aligned buffer for identify command").
Signed-off-by: Pali Rohár <[email protected]>
Signed-off-by: Marek Behún <[email protected]>
|
|
This test checks for output specific to the sandbox blk device
"sandbox_host_blk", mark it as sandbox specific.
Signed-off-by: Patrick Delaunay <[email protected]>
|
|
Attempt to handle cases with a downstream port of a PCIe switch where
link training never completes and the link continues switching between
speeds indefinitely with the data link layer never reaching the active
state.
It has been observed with a downstream port of the ASMedia ASM2824 Gen 3
switch wired to the upstream port of the Pericom PI7C9X2G304 Gen 2
switch, using a Delock Riser Card PCI Express x1 > 2 x PCIe x1 device,
P/N 41433, wired to a SiFive HiFive Unmatched board. In this setup the
switches are supposed to negotiate the link speed of preferably 5.0GT/s,
falling back to 2.5GT/s.
However the link continues oscillating between the two speeds, at the
rate of 34-35 times per second, with link training reported repeatedly
active ~84% of the time, e.g.:
02:03.0 PCI bridge [0604]: ASMedia Technology Inc. ASM2824 PCIe Gen3 Packet Switch [1b21:2824] (rev 01) (prog-if 00 [Normal decode])
[...]
Bus: primary=02, secondary=05, subordinate=05, sec-latency=0
[...]
Capabilities: [80] Express (v2) Downstream Port (Slot+), MSI 00
[...]
LnkSta: Speed 5GT/s (downgraded), Width x1 (ok)
TrErr- Train+ SlotClk+ DLActive- BWMgmt+ ABWMgmt-
[...]
LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis+, Selectable De-emphasis: -3.5dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
[...]
Forcibly limiting the target link speed to 2.5GT/s with the upstream
ASM2824 device makes the two switches communicate correctly however:
02:03.0 PCI bridge [0604]: ASMedia Technology Inc. ASM2824 PCIe Gen3 Packet Switch [1b21:2824] (rev 01) (prog-if 00 [Normal decode])
[...]
Bus: primary=02, secondary=05, subordinate=09, sec-latency=0
[...]
Capabilities: [80] Express (v2) Downstream Port (Slot+), MSI 00
[...]
LnkSta: Speed 2.5GT/s (downgraded), Width x1 (ok)
TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
[...]
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis+, Selectable De-emphasis: -3.5dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
[...]
and then:
05:00.0 PCI bridge [0604]: Pericom Semiconductor PI7C9X2G304 EL/SL PCIe2 3-Port/4-Lane Packet Switch [12d8:2304] (rev 05) (prog-if 00 [Normal decode])
[...]
Bus: primary=05, secondary=06, subordinate=09, sec-latency=0
[...]
Capabilities: [c0] Express (v2) Upstream Port, MSI 00
[...]
LnkSta: Speed 2.5GT/s (downgraded), Width x1 (downgraded)
TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
[...]
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
[...]
Make use of this observation then and attempt to detect the inability to
negotiate the link speed automatically, and then handle it by hand. Use
the Data Link Layer Link Active status flag as the primary indicator of
successful link speed negotiation, but given that the flag is optional
by hardware to implement (the ASM2824 does have it though), resort to
checking for the mandatory Link Bandwidth Management Status flag showing
that the link speed or width has been changed in an attempt to correct
unreliable link operation (the ASM2824 does set it too).
If these checks indicate that link may not operate correctly, then poll
the Data Link Layer Link Active status flag along with the Link Training
flag for the duration of 200ms to see if the link has stabilised, that
is either that the Data Link Layer Link Active status flag has been set
or that Link Training has been inactive during at least the second half
of the interval.
If that has indicated failure, restrict the target speed to 2.5GT/s,
request a link retrain and check again if the link has stabilised. If
that does not work either, then restore the original speed setting and
claim defeat, otherwise we are done.
NB interestingly enough with the ASM2824 vs PI7C9X2G304 configuration
referred above asking the ASM2824 to retrain with a higher target link
speed once the 2.5GT/s speed has been negotiated makes the two devices
successfully negotiate 5.0GT/s. Lifting the 2.5GT/s speed restriction
would however prevent our workaround from working with an OS that issues
a reset and that is unaware of the problem. This is because the devices
would then try to negotiate a higher link speed from scratch and fail,
while the sticky property of the Target Link Speed setting will keep the
2.5GT/s speed restriction across a reset.
Keep the 2.5GT/s speed restriction then, conservatively, if functional
once applied.
Signed-off-by: Maciej W. Rozycki <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
CHUNK_TYPE_RAW buffer is not aligned, and flash sparse images by
fastboot will report "Misaligned operation" if DCACHE is enabled.
Flashing Sparse Image
CACHE: Misaligned operation at range [84000028, 84001028]
CACHE: Misaligned operation at range [84001034, 84002034]
CACHE: Misaligned operation at range [8401104c, 8401304c]
Fix it
Signed-off-by: qianfan Zhao <[email protected]>
Reviewed-by: Sean Anderson <[email protected]>
|
|
- mvebu: Move PCIe code from serdes to PCIe driver (Pali)
- mtd: nand: pxa3xx: use marvell, prefix for custom DT properties
(Pierre)
- Add PCIe support for Iomega iConnect board (Tony)
- ddr: marvell: a38x: Misc improvements / fixes (Marek)
- tools: kwbimage: Load address fixes (Pali)
- mvebu: db-88f6720: Fix CONFIG_SPL_TEXT_BASE and remove wrong memory
layout (Pali)
- mvebu: Replace hardcoded values 0x0030/0x4030 by proper calculation
(Pali)
|
|
These hardcoded values were calculated from CONFIG_SPL_TEXT_BASE macro. Now
this macro is configurable via Kconfig, so calculate values 0x0030/0x4030
at compile time via CONFIG_SPL_TEXT_BASE option. Values 0x0030/0x4030
represents offset of CONFIG_SPL_TEXT_BASE from address 0x40000000.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Memory layout in the comment is from Armada XP platform which uses load
address 0x40004030. DB-88f6720 is Armada 375 platform which uses same load
address as Armada 38x which is 0x40000030.
Currently SPL support for Armada 375 is unfinished and does not work. There
is missing Serdes initialization and DDR3 training code. So nobody noticed
that CONFIG_SPL_* options are not correct.
Fix at least CONFIG_SPL_TEXT_BASE constant and remove incorrect comments
about memory layout. So it is not misleading.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Do not check for kwbimage configuration file when just showing information
about existing kwbimage file.
The check for kwbimage configuration file is required only when creating
kwbimage, not when showing information about image or when extracting data
from image.
With this change, it is possible to call mkimage -l and dumpimage -l also
for existing kwbimage file.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
When there is no -p argument for dumpimage tool specified, extract the main
data image from kwbimage file. This makes dumpimage consistent with other
image formats.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Despite the official specification, BootROM does not look at the lowest bit
of ext field but rather checks if ext field is non-zero.
Moreover original Marvell doimage tool puts into the mhdr->ext field the
number of extended headers, so basically it sets ext filed to non-zero
value if some extended header is present.
Fix U-Boot dumpimage and kwboot tools to parse correctly also kwbimage
files created by Marvell doimage tool, in the same way as the BootROM is
doing it when booting these images.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Avoid casting const to non-const.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
To regenerate kwbimage from existing image, it is needed to have kwbimage
config file. Add a new option to generate kwbimage config file from
existing kwbimage when '-p 1' option is given.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
For debugging purposes it is good to know where the binary image would be
loaded and also it is needed to know if printed size is image size or the
size of header together with image.
Make it unambiguous by showing that printed size is not the size of the
whole header, but only the size of executable code, and print also the
executable offset of this binary image. Load/execute address is the offset
relative to the base address (either 0x40004000 or 0x40000000).
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Data delay is stored as 8-bit number in kwbimage structure. Ensure the
given value is at most 255.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
BootROMs on pre-A38x SoCs enabled its output on UART by default, but A38x'
BootROM has its output on UART disabled by default.
To enable BootROM output on A38x SoC, it is required to set DEBUG flag
(which only enables BootROM output and nothing more) in kwbimage. For UART
images this DEBUG flag is ignored by BootROM.
Enable kwbimage DEBUG flag for all A38x boards.
With this change BootROM prints the following (success) information on UART
before booting U-Boot kwbimage:
BootROM - 1.73
Booting from SPI flash
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
This alignment is required only for platforms based on Sheeva CPU core
which are A370 and AXP. Now when U-Boot build system correctly propagates
LOAD_ADDRESS there is no need to have enabled 128-bit boundary alignment on
platforms which do not need it. Previously it was required because load
address was implicitly rounded to 128-bit boundary and U-Boot build system
expected it and misused it. Now with explicit setting of LOAD_ADDRESS there
is no guessing for load address anymore.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
U-Boot SPL for mvebu platform is not compiled as position independent.
Therefore it is required to instruct BootROM to load U-Boot SPL at the
correct address. Loading of kwbimage binary code at specific address can be
now achieved by the new LOAD_ADDRESS token as part of BINARY command in
kwbimage config file.
Update mvebu Makefile to put value of $(CONFIG_SPL_TEXT_BASE) into
LOAD_ADDRESS token when generating kwbimage.cfg from kwbimage.cfg.in.
It is required to update regex for sed to find replacement tokens at any
position on a line in kwbimage config file and not only at the beginning of
the line. This is because LOAD_ADDRESS is specified at the end of line
containing the BINARY command.
It looks like all Armada boards set CONFIG_SPL_TEXT_BASE to value
0x40004030 or 0x40000030. Why this value? It is because main kwbimage
header is at address 0x40004030 or 0x40000000 and it is 32 bytes long.
After the main header there is the binary header, which consist of 1 byte
for type, 3 bytes for size, 1 byte for number of arguments, 3 reserved
bytes and then 4 bytes for each argument. After these arguments comes the
executable code.
So arguments start at address 0x40004028 or 0x40000028. Before commit
e6571f38c943 ("arm: mvebu: Remove dummy BIN header arguments for SPL
binary") there were two (dummy) arguments, which resulted in load address
of 0x40004030 or 0x40000030, always. After that commit (which removed dummy
arguments), load address stayed same due to the 128-bit alignment done by
mkimage.
This patch now reflects the dependency between $(CONFIG_SPL_TEXT_BASE),
load address and dummy kwbimage arguments, and allows the user to adjust
$(CONFIG_SPL_TEXT_BASE) config option to some other value.
For unsupported values, when mkimage/kwbimage cannot set chosen load address
as specified by $(CONFIG_SPL_TEXT_BASE), the build process now fails,
instead of silently generating non-working kwbimage.
Removal of this alignment between $(CONFIG_SPL_TEXT_BASE) and LOAD_ADDRESS
can only be done by compiling U-Boot SPL as position independent. But this
currently is not possible for 32-bit ARM version of U-Boot SPL.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
kwbimage needs to know CPU type, so set it in kwbimage config file.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
BootROM loads kwbimage header to L2-SRAM and BootROM reserve only 192 kB for it.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Function image_headersz_v1() may return zero on fatal errors.
In this case the function already printed an error message.
Check the return value of image_headersz_v1() in kwbimage_generate(),
and exit on zero value with EXIT_FAILURE.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
ARM executable code included in kwbimage binary header, which is not
position independent, needs to be loaded and executed by BootROM at the
correct fixed address.
Armada BootROMs load kwbimage header (in which the executable code is also
stored) at fixed address 0x40004000 or 0x40000000 which is mapped to
L2-SRAM (L2 Cache as SRAM). Address 0x40004000 is used on Armada platforms
with Sheeva CPU core (A370 and AXP) where BootROM uses MMU with 0x4000
bytes for MMU translation table. Address 0x40000000 is used on all other
platforms.
Thus the only way to specify load and execute address of this executable
code in binary kwbimage header is by filling dummy arguments into the
binary header, using the same mechanism we already have for achieving
128-bit boundary alignment on A370 and AXP SoCs.
Extend kwbimage config file parser to allow to specify load address as
part of BINARY command with syntax:
BINARY path_to_binary arg1 arg2 ... argN LOAD_ADDRESS address
If the specified load address is invalid or cannot be used, mkimage will
throw fatal error and exit. This will prevent generating kwbimage with
invalid load address for non-position independent binary code.
If no load address is specified, kwbimage will not fill any the dummy
arguments, thus it will behave the same as before this change.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
For other changes it is required to know if CPU core is Sheeva or not.
Therefore add a new command CPU for specifying CPU.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Usage of $(call cmd,...) is standard way to call other commands which
generate things.
It also has the advantage of printing build information in the form
KWBCFG arch/arm/mach-mvebu/kwbimage.cfg
if verbosity is disabled, and printing the build command otherwise.
Note that the '#' character needs to be escaped in Makefile when used as
value for make variable assignment.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Preserve the order of BINARY, DATA and DATA_DELAY commands as they appear
in the input file. They may depend on each other.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Register set header consists of sequence of DATA commands followed by
exactly one DATA_DELAY command. Thus if we are generating image with
multiple DATA_DELAY commands, we need to create more register set headers.
Fix calculation of image size with multiple DATA_DELAY commands and
correctly set pointer to struct register_set_hdr_v1 when initializing new
register set header.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Deduplicate code that finishes OPT_HDR_V1_REGISTER_TYPE header by
extracing it into separate function.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Mark all local functions as static.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
This is a cleaned up and fixed version of a patch
mv_ddr: a380: fix SPLIT_OUT_MIX state decision
in each pattern cycle the bus state can be changed
in order to avoide it, need to back to the same bus state on each
pattern cycle
by
Moti Boskula <[email protected]>
The original patch is not in Marvell's mv-ddr-marvell repository. It was
gives to us by Marvell to fix an issues with DDR training on some
boards, but it cannot be applied as is to mv-ddr-marvell, because it is
a very dirty draft patch that would certainly break other things, mainly
DDR4 training code in mv-ddr-marvell, since it changes common functions.
I have cleaned up the patch and removed stuff that seemed unnecessary
(when removed, it still fixed things). Note that I don't understand
completely what the code does exactly, since I haven't studied the DDR
training code extensively (and I suspect that no one besides some few
people in Marvell understand the code completely).
Anyway after the cleanup the patch still fixes isssues with DDR training
on the failing boards.
There was also a problem with the original patch on some of the Allied
Telesis' x530 boards, reported by Chris Packham. I have asked Chris to
send me some logs, and managed to fix it:
- if you look at the change, you'll notice that it introduces
subtraction of cur_start_win[] and cur_end_win[] members, depending on
a bit set in the current_byte_status variable
- the original patch subtracted cur_start_win[] if either
BYTE_SPLIT_OUT_MIX or BYTE_HOMOGENEOUS_SPLIT_OUT bits were set, but
subtracted cur_end_win[] only if the first one (BYTE_SPLIT_OUT_MIX)
was set
- from Chris Packham logs I discovered that the x530 board where the
original patch introduced DDR training failure, only the
BYTE_HOMOGENEOUS_SPLIT_OUT bit was set, and on our boards where the
patch is needed only the BYTE_SPLIT_OUT_MIX is set in the
current_byte_status variable
- this led me to the hypothesis that both cur_start_win[] and
cur_end_win[] should be subtracted only if BYTE_SPLIT_OUT_MIX bit is
set, the BYTE_HOMOGENEOUS_SPLIT_OUT bit shouldn't be considered at all
- this hypothesis also gains credibility when considering the commit
title ("fix SPLIT_OUT_MIX state decision")
Hopefully this will fix things without breaking anything else.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Tested-by: Chris Packham <[email protected]>
|
|
I got an
<[email protected]>: host mxlb.ispgateway.de[80.67.18.126] said:
554 Sorry, no mailbox here by that name. (in reply to RCPT TO command)
when sending e-mail to [email protected].
Drop Dirk Eibach from MAINTAINERS of board/gdsys/a38x and
board/gdsys/mpc8308. The latter would be left maintainerless, add
Mario Six <[email protected]> (he is also maintainer of the former
board).
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Before commit 4c289425752f ("mv_ddr: a38x: add support for ddr async
mode"), Asynchornous Mode was only used when the CPU Subsystem Clock
Options[4:0] field in the SAR1 register was set to value 0x13: CPU at
2 GHz and DDR at 933 MHz.
Then commit 4c289425752f ("mv_ddr: a38x: add support for ddr async
mode") added support for Asynchornous Modes with frequencies other than
933 MHz (but at least 467 MHz), but the code it added to check for
whether Asynchornous Mode should be used is wrong: it checks whether the
frequency setting in board DDR topology map is set to value other than
MV_DDR_FREQ_SAR.
Thus boards which define a specific value, greater than 400 MHz, for DDR
frequency in their board topology (e.g. Turris Omnia defines
MV_DDR_FREQ_800), are incorrectly put into Asynchornous Mode after that
commit.
The A38x Functional Specification, section 10.12 DRAM Clocking, says:
In Synchornous mode, the DRAM and CPU clocks are edge aligned and run
in 1:2 or 1:3 CPU to DRAM frequency ratios.
Change the check for whether Asynchornous Mode should be used according
to this explanation in Functional Specification.
Signed-off-by: Marek Behún <[email protected]>
Tested-by: Chris Packham <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Add myself as maintainer.
Signed-off-by: Tony Dinh <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
- Add board_late_init function to enable pci_init
Signed-off-by: Tony Dinh <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
- Add MVEBU PCIe configs
- Also add SYS_THUMB_BUILD to keep u-boot image size within 512K
Signed-off-by: Tony Dinh <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
The DT properties for the "enable-arbiter" and "keep-config" config
knobs were previously named inconsistently:
- The u-boot driver used "nand-enable-arbiter" and "nand-keep-config"
names, without Marvell prefixes.
- The Linux driver uses "marvell,nand-keep-config" ("enable-arbiter"
does not exist anymore in recent kernels, but it also used to be
"marvell,nand-enable-arbiter").
- The device trees almost all use "marvell," prefixed names, except for
one single instance of "nand-enable-arbiter" without vendor prefix.
This commit standardizes on the vendor prefixed version, making the
u-boot driver read from DT props "marvell,nand-enable-arbiter" and
"marvell,nand-keep-config". The one device tree using the unprefixed
version is also changed to use the new naming.
This has the side effect of making the previously no-op "marvell,"
config knobs already present in some DTs actually do something. This was
likely the original intention of the DT authors, but note that this
commit was not tested on every single impacted board.
Signed-off-by: Pierre Bourdon <[email protected]>
|
|
As explained in commit 3bedbcc3aa18 ("arm: mvebu: a38x: serdes: Don't
overwrite read-only SAR PCIe registers") it is required to set Maximum Link
Width bits of PCIe Root Port Link Capabilities Register depending of number
of used serdes lanes. As this register is part of PCIe address space and
not serdes address space, move it into pci_mvebu.c driver.
Read number of PCIe lanes from DT property "num-lanes" which is used also
by other PCIe controller drivers in Linux kernel. If this property is
absent then it defaults to 1. This property needs to be set to 4 for every
mvebu board which use PEX_ROOT_COMPLEX_X4 or PEX_BUS_MODE_X4.
Enabling of PCIe port needs to be done afer all registers in PCIe address
space are properly configure. For this purpose use new mvebu-reset driver
(part of system-controller) and remove this code from serdes code.
Because some PCIe ports cannot be enabled individually, it is required to
first setup all PCIe ports and then enable them.
This change contains also all required "num-lanes" and "resets" DTS
properties, to make pci_mvebu.c driver work correctly.
Signed-off-by: Pali Rohár <[email protected]>
|
|
ports
Enabling and disabling PCIe ports is done via address space of system
controller. All 32-bit Armada SoCs use low 4 bits in SoC Control 1 Register
for enabling and disabling some or more PCIe ports. Correct mapping needs
to be set in particular DTS files.
DT API for mvebu-reset is prepared for implementing resets also for other
HW blocks, but currently only PCIe is implemented via index 0.
Currently this driver is not used as PCIe ports are automatically enabled
by SerDes code executed by U-Boot SPL. But this will change in followup
patches.
Signed-off-by: Pali Rohár <[email protected]>
|
|
After function mvebu_pcie_probe() returns U-Boot DM expects that PCIe link
is already up. In followup patches link initialization will be moved from
SPL to proper and therefore explicitly link up delay is required.
Delay mvebu_pcie_probe() for 100ms to ensure that PCIe link is up after
function finish. In the case when no card is connected to the PCIe slot,
this will delay probe time by 100ms, which should not be problematic.
This change fixes detection and initialization of some QCA98xx cards on
the first serdes when configured in x1 mode. Default configuration of
the first serdes on A385 is x4 mode, so it looks as if some delay is
required when x4 is changed to x1 and card correctly links with A385.
Other PCIe serdes ports on A385 are x1-only, and so they don't have this
problem.
Signed-off-by: Pali Rohár <[email protected]>
|
|
In first phase just parse DT properties and fill struct mvebu_pcie. In
second phase setup all PCIe links (without enabling them). And in the last
third phase enable all PCIe links and create UCLASS_PCI device for each
one.
Because parsing of DT is done before UCLASS_PCI is created, we cannot use
DM for this action anymore. So remove .of_to_plat callback and replace it
by ad-hoc function for parsing DT properties and filling struct mvebu_pcie.
Signed-off-by: Pali Rohár <[email protected]>
|
|
SoC specific macro SOC_REGS_PHY_BASE is used for two things:
* calculation of base PCIe port address
* filling PCIe register with address of internal registers
For calculating base PCIe port address use function
ofnode_translate_address() which translates DT "assigned-addresses" to
final PCIe port address.
And for calculating address of internal registers use untranslated and
translated DT "assigned-addresses".
Basically this change reads SOC_REGS_PHY_BASE address indirectly from DT.
Signed-off-by: Pali Rohár <[email protected]>
|
|
Function mvebu_pcie_port_parse_dt() is called only from
mvebu_pcie_of_to_plat() function. Both these function parse DT properties
required to setup mvebu pcie. So inline mvebu_pcie_port_parse_dt() function
into mvebu_pcie_of_to_plat() to have all code related to parsing DT
properties at one place.
Signed-off-by: Pali Rohár <[email protected]>
|
|
Do not call pci_set_region() for resources which were not properly mapped.
This prevents U-Boot to access unmapped memory space.
Update MBUS_PCI_MEM_SIZE and MBUS_PCI_IO_SIZE macros to cover all PCIe MEM
and IO ranges. Previously these macros covered only address ranges for the
first PCIe port. Between MBUS_PCI_IO_BASE and MBUS_PCI_MEM_BASE there is
space for six 128 MB long address ranges. So set MBUS_PCI_MEM_SIZE to value
of 6*128 MB. Similarly set MBUS_PCI_IO_SIZE to 6*64 KB.
Function resource_size() returns zero when start address is 0 and end
address is -1. So set invalid resources to these values to indicate that
resource has no mapping.
Split global PCIe MEM and IO resources (defined by MBUS_PCI_*_* macros)
into PCIe ports in mvebu_pcie_bind() function which allocates per-port
based struct mvebu_pcie, instead of using global state variables
mvebu_pcie_membase and mvebu_pcie_iobase. This makes pci_mvebu.c driver
independent of global static variables (which store the state of
allocation) and allows to bind and unbind the driver more times.
Signed-off-by: Pali Rohár <[email protected]>
Signed-off-by: Marek Behún <[email protected]>
|
|
A385 controlcenterdc board does not use PCI DM properly and touches some
PCIe devices directly in its board code.
This controlcenterdc spl_board_init() function expects that PCIe link is
already initialized. Link itself is initialized in a38x serdes code but
this will change in future and link initialization will be postponed from
U-Boot SPL to proper U-Boot.
So explicitly enable PCIe link 2 in spl_board_init() function via
SoC Control Register 1 to not break this code by future changes. This board
has PCIe link 2 just x1, so no additional initialization (except enabling
PCIe port) is needed.
Signed-off-by: Pali Rohár <[email protected]>
|
|
The only user of board_pex_config() weak function is A385 controlcenterdc
board. It looks like that code in its board_pex_config() function needs to
be executed after PCIe link is up. Therefore put this code into
spl_board_init() function which is called after a38x serdes initialization,
and therefore it is after the serdes hws_pex_config() function finishes
(which is the state before this change).
With this change completely remove board_pex_config() function as it is not
used anymore.
Signed-off-by: Pali Rohár <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-dm
bloblist prep for standard passage
switch order of pinctrl and power domain calls
various minor fixes
|
|
This implementation is intended to be copied to other projects and
modified, to as to foster a standard means of communcating runtime
information between firmware projects.
The GPL-2 license is too restrictive for some projects, e.g. those
intended as reference implementations rather than designed for
collaborative open-source development.
Update the license to make this easier to share.
Signed-off-by: Simon Glass <[email protected]>
|
|
FIx up various minor errors and add the API documentation to the bloblist
docs, since it is quite useful to see it in the same place.
Signed-off-by: Simon Glass <[email protected]>
|
|
Add a few convenience functions to obtain useful information about the
bloblist.
Signed-off-by: Simon Glass <[email protected]>
|
|
At present we do support allocating the bloblist but the Kconfig is a bit
strange, since we still have to specify an address in that case. Partly
this is because it is a pain to have CONFIG options that disappears when
its dependency is enabled. It means that we must have #ifdefs in the code,
either in the C code or header file.
Make use of IF_ENABLED_INT() and its friend to solve that problem, so we
can separate out the location of bloblist into a choice. Put the address
and size into variables so we can log the result.
Add the options for SPL as well, so we can use CONFIG_IS_ENABLED().
Signed-off-by: Simon Glass <[email protected]>
|
