summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2021-12-27CI: Test for unmigrated CONFIG symbols in board config.h filesTom Rini
Now that all symbols that exist in Kconfig no longer also have boards setting them in the board config.h file, add a CI test to catch new instances of this, and fail. Signed-off-by: Tom Rini <[email protected]>
2021-12-27Convert CONFIG_SYS_I2C_EEPROM_ADDR_LEN to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_I2C_EEPROM_ADDR_LEN Signed-off-by: Tom Rini <[email protected]>
2021-12-27ppc: mpc83xx: Remove unused CONFIG symbolsTom Rini
Neither of these symbols are referenced anywhere else, so remove them. Signed-off-by: Tom Rini <[email protected]>
2021-12-27Convert CONFIG_83XX_PCICLK to KconfigTom Rini
This converts the following to Kconfig: CONFIG_83XX_PCICLK Signed-off-by: Tom Rini <[email protected]>
2021-12-27Finish conversion of CONFIG_SYS_CLK_FREQ to KconfigTom Rini
In order to finish moving this symbol to Kconfig for all platforms, we need to do a few more things. First, for all platforms that define this to a function, introduce CONFIG_DYNAMIC_SYS_CLK_FREQ, similar to CONFIG_DYNAMIC_DDR_CLK_FREQ and populate clock_legacy.h. This entails also switching all users from CONFIG_SYS_CLK_FREQ to get_board_sys_clk() and updating a few preprocessor tests. With that done, all platforms that define a value here can be converted to Kconfig, and a fall-back of zero is sufficiently safe to use (and what is used today in cases where code may or may not have this available). Make sure that code which calls this function includes <clock_legacy.h> to get the prototype. Signed-off-by: Tom Rini <[email protected]>
2021-12-27CONFIG_SYS_CLK_FREQ: Consistently be static or get_board_sys_clk()Tom Rini
This CONFIG option is used in one of two ways. The first way is that it is defined to a static value, of an unsigned long size. The second way is that it is defined to something, typically a function, to determine this value at run time. However, in a few cases that function returns a static value. Change that to using the static value directly. In the case of using something at run time, convert everything to using a function of the same name and prototype. This will allow for further cleanups. Finally, we have a few cases where the function is just not used, so drop it. Signed-off-by: Tom Rini <[email protected]>
2021-12-27nxp: ics307_clk: Guard get_board_ddr_clk function correctlyTom Rini
When we have CONFIG_DYNAMIC_DDR_CLK_FREQ set is the only time we should have this function, so guard it so that we can include <clock_legacy.h> in this file later on. Signed-off-by: Tom Rini <[email protected]>
2021-12-27ls1088a: Guard get_board_ddr_clk function correctlyTom Rini
When we have CONFIG_DYNAMIC_DDR_CLK_FREQ set is the only time we should have this function, so guard it so that we can include <clock_legacy.h> in this file later on. Signed-off-by: Tom Rini <[email protected]>
2021-12-27arm: s5pc1xx: Move CONFIG_SYS_CLK_FREQ_C1x0 out of CONFIG namespaceTom Rini
The values CONFIG_SYS_CLK_FREQ_C100 and CONFIG_SYS_CLK_FREQ_C110 are only used in one place and not changed by the board config file. Move these out of the CONFIG namespace and in to the CFG namespace. Signed-off-by: Tom Rini <[email protected]>
2021-12-27Convert CONFIG_ARCH_MAP_SYSMEM to KconfigTom Rini
This converts the following to Kconfig: CONFIG_ARCH_MAP_SYSMEM Signed-off-by: Tom Rini <[email protected]>
2021-12-27Convert CONFIG_SYS_NAND_U_BOOT_OFFS to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_NAND_U_BOOT_OFFS Signed-off-by: Tom Rini <[email protected]>
2021-12-27Convert CONFIG_TPL_TEXT_BASE to KconfigTom Rini
This converts the following to Kconfig: CONFIG_TPL_TEXT_BASE Signed-off-by: Tom Rini <[email protected]>
2021-12-27Convert CONFIG_ZYNQMP_PSU_INIT_ENABLED to KconfigTom Rini
This converts the following to Kconfig: CONFIG_ZYNQMP_PSU_INIT_ENABLED Signed-off-by: Tom Rini <[email protected]>
2021-12-27Finish conversion CONFIG_SYS_NAND_SELF_INIT to KconfigTom Rini
In order to finish this conversion we need to add a symbols for SPL_SYS_NAND_SELF_INIT and TPL_SYS_NAND_SELF_INIT as there are cases there where we need to, or need to not, use that framework as things stand. Signed-off-by: Tom Rini <[email protected]>
2021-12-27Convert CONFIG_TEGRA_NAND to KconfigTom Rini
This converts the following to Kconfig: CONFIG_TEGRA_NAND Signed-off-by: Tom Rini <[email protected]>
2021-12-27Finish converting CONFIG_SYS_FSL_CLK to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_FSL_CLK We move the exiting option to common/Kconfig near the other options to control the contents of board_init_f() and note that this is a legacy option. We further restrict this to where the call is going to be non-empty, for the SoCs that had only been using this for some MMC-related clocks. Signed-off-by: Tom Rini <[email protected]>
2021-12-27warp7, pic32mzdask: Remove SYS_FDT_ADDR/SYS_ENV_ADDR from CONFIG namespaceTom Rini
In the case of CONFIG_SYS_FDT_ADDR this was being used to modify the default value of fdt_addr / fdt_addr_r, which is not something to expose in this manner and is not otherwise done. The case of SYS_ENV_ADDR is similar but only done on the pic32mzdask platform, for scriptaddr. Signed-off-by: Tom Rini <[email protected]>
2021-12-27Convert CONFIG_SYS_PCI_64BIT to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_PCI_64BIT Signed-off-by: Tom Rini <[email protected]>
2021-12-27Finish CONFIG_VID et al conversion to KconfigTom Rini
This converts the following to Kconfig: CONFIG_VID CONFIG_VOL_MONITOR_INA220 CONFIG_VOL_MONITOR_IR36021_READ CONFIG_VOL_MONITOR_IR36021_SET CONFIG_VOL_MONITOR_LTC3882_READ CONFIG_VOL_MONITOR_LTC3882_SET To finish this migration, we first need to introduce CONFIG_SPL_VID as some platforms only use this code in full U-Boot while others use it in SPL as well. To make the Kconfig logic clearer, guard all of the sub-options with a if VID || SPL_VID check. Finally, add Kconfig options for the remaining related options that did not previously have one. Signed-off-by: Tom Rini <[email protected]>
2021-12-27Convert CONFIG_SYS_IMMR to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_IMMR We do this by consolidating the SYS_IMMR options we have and providing defaults. We also, in the few places where M68K was also sharing code with these platforms, define it within the file to CONFIG_SYS_MBAR to match usage. This should be cleaned up longer term. Signed-off-by: Tom Rini <[email protected]>
2021-12-27Convert CONFIG_SYS_MEMTEST_START et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_MEMTEST_START CONFIG_SYS_MEMTEST_END This is removing unused defines and correcting the default value to be 0x0 as we are a hex symbol. Signed-off-by: Tom Rini <[email protected]>
2021-12-27Convert CONFIG_WATCHDOG_TIMEOUT_MSECS to KconfigTom Rini
This converts the following to Kconfig: CONFIG_WATCHDOG_TIMEOUT_MSECS Signed-off-by: Tom Rini <[email protected]>
2021-12-27Finish converting CONFIG_WATCHDOG, HW_WATCHDOG and WDT to KconfigTom Rini
Because of how these symbols work, and the remaining board config.h file uses, we need to do these at the same time. In some cases we just get to move rather directly to the defconfigs. A few cases require manual intervention. For the case of the eb_cpu5282 we need to select HW_WATCHDOG for the target, given how it's implemented. For the cases of m53menlo, dh_imx6, display5, and display5_factory we disable SPL watchdog support as the particular combination of options they want would require either more symbols or enabling SPL_DM. Signed-off-by: Tom Rini <[email protected]>
2021-12-27pci: Remove unused FSL_PCI_INIT codeTom Rini
The symbol CONFIG_FSL_PCI_INIT is no longer enabled anywhere, removed now unused code. Signed-off-by: Tom Rini <[email protected]>
2021-12-27Convert CONFIG_SYS_NAND_DRIVER_ECC_LAYOUT to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_NAND_DRIVER_ECC_LAYOUT In order to do this conversion, expose this option to the user and use "save" not "safe" in the text. Signed-off-by: Tom Rini <[email protected]>
2021-12-27Convert CONFIG_SUPPORT_EMMC_RPMB to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SUPPORT_EMMC_RPMB This fixes a few platforms where the option was not taking effect as intended. Signed-off-by: Tom Rini <[email protected]>
2021-12-27Remove CONFIG_SYS_MMC_IMG_LOAD_PART from CONFIG namespaceTom Rini
This option is used as part of configuring the default environment for a number of platforms. However, it is always set to 1 and the only time it is part of Kconfig, it is used in a hard-coded manner. Hard-code the value in the environment instead. Signed-off-by: Tom Rini <[email protected]>
2021-12-27Convert CONFIG_CONS_INDEX et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_CONS_INDEX CONFIG_DEBUG_UART_CLOCK CONFIG_FSL_TZPC_BP147 CONFIG_GENERIC_ATMEL_MCI CONFIG_IDENT_STRING CONFIG_LIBATA CONFIG_LNX_KRNL_IMG_TEXT_OFFSET_BASE CONFIG_LPC32XX_GPIO CONFIG_MP CONFIG_MPC8XXX_GPIO CONFIG_MTD_PARTITIONS CONFIG_MVGBE CONFIG_MXC_GPIO CONFIG_NR_DRAM_BANKS CONFIG_OF_BOARD_SETUP CONFIG_OF_STDOUT_VIA_ALIAS CONFIG_OF_SYSTEM_SETUP CONFIG_PREBOOT CONFIG_ROCKCHIP_SERIAL CONFIG_RTC_ENABLE_32KHZ_OUTPUT CONFIG_RTC_MV CONFIG_SCSI_AHCI CONFIG_SF_DEFAULT_BUS CONFIG_SF_DEFAULT_CS CONFIG_SF_DEFAULT_SPEED CONFIG_SOFT_SPI CONFIG_SPI_FLASH_EON CONFIG_SPI_FLASH_MACRONIX CONFIG_SPI_FLASH_MTD CONFIG_SPI_FLASH_SPANSION CONFIG_SPI_FLASH_SST CONFIG_SPI_FLASH_STMICRO CONFIG_SUPPORT_RAW_INITRD CONFIG_SYS_ARCH_TIMER CONFIG_SYS_BOARD CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE CONFIG_SYS_DCACHE_OFF CONFIG_SYS_FDT_SAVE_ADDRESS CONFIG_SYS_FLASH_CFI CONFIG_SYS_FSL_ERRATUM_ESDHC135 CONFIG_SYS_HAS_SERDES CONFIG_SYS_L2CACHE_OFF CONFIG_SYS_LITTLE_ENDIAN CONFIG_SYS_LOAD_ADDR CONFIG_SYS_MMCSD_FS_BOOT_PARTITION CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR CONFIG_SYS_NS16550 CONFIG_SYS_PLLFIN CONFIG_SYS_SPI_U_BOOT_OFFS CONFIG_TIMER_SYS_TICK_CH CONFIG_USB_EHCI_FSL CONFIG_U_QE CONFIG_VERSION_VARIABLE Signed-off-by: Tom Rini <[email protected]>
2021-12-27Convert CONFIG_SD_BOOT et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SD_BOOT CONFIG_SD_BOOT_QSPI Signed-off-by: Tom Rini <[email protected]>
2021-12-27Convert CONFIG_FSL_IFC to KconfigTom Rini
This converts the following to Kconfig: CONFIG_FSL_IFC This is done via select statements to match previous logic. Signed-off-by: Tom Rini <[email protected]>
2021-12-27Convert CONFIG_ENV_SPI_BUS et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_ENV_SPI_BUS CONFIG_ENV_SPI_CS CONFIG_ENV_SPI_MAX_HZ CONFIG_ENV_SPI_MODE As part of this, we use Kconfig to provide the defaults now that were done in include/spi_flash.h. We also in some cases change from using CONFIG_ENV_SPI_FOO to CONFIG_SF_DEFAULT_FOO as those were the values in use anyhow as ENV was not enabled. Signed-off-by: Tom Rini <[email protected]>
2021-12-27Clarify CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW in KconfigTom Rini
This is a "hex" prompt but the default value was given as an int. Switch the default to hex (0x0) and remove the defconfigs that were using the default, but as hex before. Signed-off-by: Tom Rini <[email protected]>
2021-12-27arm: Drop unused tam3517-common.hTom Rini
With the relevant platforms removed, drop this file. Signed-off-by: Tom Rini <[email protected]>
2021-12-27doc: Fix usage of CFG_RPMB_WRITE_KEYIlias Apalodimas
This is a 'y/n' selection, so fix it. While at it remove the duplicate usage of CFG_CORE_HEAP_SIZE Signed-off-by: Ilias Apalodimas <[email protected]> Acked-by: Heinrich Schuchardt <[email protected]>
2021-12-27video: mxsfb: fix clk_get_by_name() return value checkGiulio Benetti
If clk_get_by_name() returns 0 it means it executed successfully while now we consider it as an error. So let's check if return value is negative to be an error. Otherwise this prevents "axi" and "disp_axi" to be enabled. Signed-off-by: Giulio Benetti <[email protected]>
2021-12-26x86: coreboot: Add a sample script to build a qemu imageSimon Glass
It is useful to boot coreboot (with U-Boot as a payload) from qemu. Add a sample script to show how to do this. Signed-off-by: Simon Glass <[email protected]>
2021-12-26x86: coreboot: Support getting a logo from virtioSimon Glass
Enable this feature so that a splash screen can be provided. Signed-off-by: Simon Glass <[email protected]>
2021-12-26video: Support virtio devices with the splash screenSimon Glass
This is useful for showing a logo when booting from qemu. Signed-off-by: Simon Glass <[email protected]>
2021-12-26video: Show the U-Boot logo by defaultSimon Glass
Enable this for boards with a display, unless they are using the SPLASH feature. This shows a U-Boot logo on boards with a display, which seems like a useful thing. Signed-off-by: Simon Glass <[email protected]>
2021-12-26video: Support showing the U-Boot logoSimon Glass
Show the U-Boot logo by default. This is only 7KB in size so seems like a useful default for boards that enable a display. If SPLASH_SCREEN is enabled, it is not enabled by default, so as not to conflict with that feature. Also disable it for tests, since we don't want to complicate the output. Signed-off-by: Simon Glass <[email protected]>
2021-12-26video: Drop VIDEO_LOGO from cfb_consoleSimon Glass
This driver is obsolete and only used by nokia_rx51. It should be deleted. For now, drop the VIDEO_LOGO code to avoid confusion with the new implementation. Signed-off-by: Simon Glass <[email protected]>
2021-12-26video: Convert CONFIG_VIDEO_LOGO to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_VIDEO_LOGO Note that this option depends on CONFIG_DM_VIDEO now, since cfb_console is deprecated. The only relevant code is now in splash.c Drop the check for DM_VIDEO in that file. Signed-off-by: Simon Glass <[email protected]>
2021-12-26video: Drop #ifdefs from video_bmpSimon Glass
Convert the current preprocessor macros to C code. Signed-off-by: Simon Glass <[email protected]>
2021-12-26video: theadorable: Use RGB565 for BMP blittingSimon Glass
At present this uses RGB555 format for blitting to a display. Sandbox uses 565 and that seems to be more normal for BMP as well. Update the code accordingly and add a test. Note that this likely breaks the theadorable board so we may need to discuss supporting both formats. Signed-off-by: Simon Glass <[email protected]>
2021-12-26video: Add a test for 16bpp BMP filesSimon Glass
Add a compressed 16bpp BMP file and a test to cover this. Signed-off-by: Simon Glass <[email protected]>
2021-12-26video: Tidy up 24/32 BMP blittingSimon Glass
Drop the unnecessary brackets. Signed-off-by: Simon Glass <[email protected]>
2021-12-26video: Drop the uclass colour mapSimon Glass
We don't need this anymore since we use the BMP palette directly. Drop it. Signed-off-by: Simon Glass <[email protected]>
2021-12-26video: bmp: Update RLE8 support to use the write functionSimon Glass
Update this code to use write_pix8() rather than writing the pixels only for a single supported display depth. This allows us to support any depth. Add some more tests too. Signed-off-by: Simon Glass <[email protected]>
2021-12-26video: Move BMP pixel-writing into a functionSimon Glass
At present the code that writes to a pixel is quite convoluted. It uses a colour map which is in the uclass and the same code is repeated in different places within video_bmp_display(). As a first step, create a function which can write a pixel from the bitmap, no matter what the display depth. Use any provided palette directly, rather than using the uclass version. Signed-off-by: Simon Glass <[email protected]>
2021-12-26video: Drop fb_put_byte() el atSimon Glass
These functions are not used with driver model, nor in any U-Boot boards. Drop them and inline the code. Signed-off-by: Simon Glass <[email protected]>
generated by cgit v1.3.1 (git 2.54.0) at 2026-09-01 01:44:03 +0000