| Age | Commit message (Collapse) | Author |
|---|
|
UCLASS_IRQ driver is not Intel specific. Make CONFIG_IRQ
selectable for all platforms.
Signed-off-by: Wasim Khan <[email protected]>
Tested-by: Vladimir Oltean <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
The GICv3 RM requires "The first 1KB of memory for the LPI Pending tables
must contain only zeros on initial allocation, and this must be visible
to the Redistributors, or else the effect is UNPREDICTABLE".
And as the following statement, we here clear the whole Pending tables
instead of the first 1KB.
"An LPI Pending table that contains only zeros, including in the first 1KB,
indicates that there are no pending LPIs.
The first 1KB of the LPI Pending table is IMPLEMENTATION DEFINED. However,
if the first 1KB of the LPI Pending table and the rest of the table contain
only zeros, this must indicate that there are no pending LPIs."
And there isn't any pending LPI under U-Boot, so it's unnecessary to
load the contents of the Pending table during the enablement, then set
the GICR_PENDBASER.PTZ flag.
Signed-off-by: Hou Zhiqiang <[email protected]>
Tested-by: Vladimir Oltean <[email protected]> # NXP LS1028A
Reviewed-by: Wasim Khan <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
Signed-off-by: Neil Armstrong <[email protected]>
|
|
Let's add a boot target for NVMe so we can do a full boot over NVMe.
Signed-off-by: Neil Armstrong <[email protected]>
|
|
Now we have PCIe, let's also enable NVMe to access an eventual NVMe SSDs
connected on the M.2 slot.
Signed-off-by: Neil Armstrong <[email protected]>
|
|
Enable PCIe by default in u-boot, this should eventually be made dynamic
in the runtime board config depending on the MCU configuration.
Signed-off-by: Neil Armstrong <[email protected]>
|
|
Add the PCIe part of the G12A USB3 PCIe Combo PHY driver.
Signed-off-by: Neil Armstrong <[email protected]>
|
|
Add missing gates used for PCIe.
Signed-off-by: Neil Armstrong <[email protected]>
|
|
The sync of the device tree and dt-bindings from Linux v5.6-rc2
11a48a5a18c6 ("Linux 5.6-rc2") causes Ethernet to break on some
ODROID-C2. The PHY seems to need proper reset timing to be functional
in U-Boot and Linux afterwards. Readd the old PHY reset bindings for
dwmac until we support the new bindings in the PHY node.
Fixes: dd5f2351e99a ("arm64: dts: meson: sync dt and bindings from v5.6-rc2")
Signed-off-by: Stefan Agner <[email protected]>
Signed-off-by: Neil Armstrong <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-amlogic
- fix Ethernet on Odroid-C2 by re-adding old bindings style PHY reset
- add G12A PCIe clock gates
- add G12A PCIe PHY OPs
- enable PCIe for Khadas VIM3/VIM3L boards DT
- enable PCIe and NVME for Khadas VIM3/VIM3L boards config
- update Amlogic board documentation for PCIe support
|
|
https://source.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features for 2021.07 cycle:
This small feature set include support for 5th PIO bank on pio4 pinctrl
driver and a fix for the SPL on sama5d3.
|
|
This reverts commit 38d6b7ebdaee3e0e8426ef1b9df88bdce8ae2e75.
struct global_data contains a pointer to the bd_info structure. This
pointer was populated spl_set_bd() to a pre-allocated bd_info in the
".data" section. The referenced commit replaced this mechanism to one
that uses malloc(). That new mechanism is only used if SPL_ALLOC_BD=y.
which very few boards do.
The result is that (struct global_data)->bd is NULL in SPL on most
platforms. This breaks falcon mode, since arch_fixup_fdt() tries to
access (struct global_data)->bd and set the "/memory" node in the
devicetree. The result is that the "/memory" node contains garbage
values, causing linux to panic() as it sets up the page table.
Instead of trying to fix the mess, potentially causing other issues,
revert to the code that worked, while this change is reworked.
Signed-off-by: Alexandru Gagniuc <[email protected]>
|
|
Signed-off-by: Neil Armstrong <[email protected]>
|
|
Let's add a boot target for NVMe so we can do a full boot over NVMe.
Signed-off-by: Neil Armstrong <[email protected]>
|
|
Now we have PCIe, let's also enable NVMe to access an eventual NVMe SSDs
connected on the M.2 slot.
Signed-off-by: Neil Armstrong <[email protected]>
|
|
Enable PCIe by default in u-boot, this should eventually be made dynamic
in the runtime board config depending on the MCU configuration.
Signed-off-by: Neil Armstrong <[email protected]>
|
|
Add the PCIe part of the G12A USB3 PCIe Combo PHY driver.
Signed-off-by: Neil Armstrong <[email protected]>
|
|
Add missing gates used for PCIe.
Signed-off-by: Neil Armstrong <[email protected]>
|
|
The sync of the device tree and dt-bindings from Linux v5.6-rc2
11a48a5a18c6 ("Linux 5.6-rc2") causes Ethernet to break on some
ODROID-C2. The PHY seems to need proper reset timing to be functional
in U-Boot and Linux afterwards. Readd the old PHY reset bindings for
dwmac until we support the new bindings in the PHY node.
Fixes: dd5f2351e99a ("arm64: dts: meson: sync dt and bindings from v5.6-rc2")
Signed-off-by: Stefan Agner <[email protected]>
Signed-off-by: Neil Armstrong <[email protected]>
|
|
in the early SPL boot stage whenever there is a call to udelay,
dm_timer_init fails to find the pit timer whenever it traverses
the device tree, if this property is not present
Signed-off-by: Manuel Reis <[email protected]>
CC: Eugen Hristev <[email protected]>
Tested-by: Derald D. Woods <[email protected]>
Reviewed-by: Eugen Hristev <[email protected]>
|
|
Change the pinctrl compatible to sama7g5, the right one for this product.
Signed-off-by: Eugen Hristev <[email protected]>
|
|
Add support for sama7g5 pinctrl variant, with 5 banks with a degraded
8 line only 5th bank.
Based on Linux Kernel implementation.
Signed-off-by: Eugen Hristev <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2021-07-rc1-2
Documentation:
man-page for fatinfo
Bug fixes:
memory leak in efi_capsule_scan_dir()
incorrect invocations of EFI_CALL macro creating ESRT table
buffer overflow in tcg2_create_digest()
|
|
This is a patchset which makes away with the .bind() controller indexing
workaround which was broken since before v2021.04, and then adds PHY
support and MX8M support on top of that. Better add it into the release
early to get as much testing as possible done, because this really does
a lot of changes to the ehci-mx6 driver.
|
|
https://source.denx.de/u-boot/custodians/u-boot-ti
- Support for pinmux status command on beaglebone
- Updates for MMC speed modes for J721e-evm
- Fix MMC booting on omap35_logic_somlv board
|
|
- SPI Flash ENV improvements / cleanups
- Redundant support for FAT
- Assorted bugfixes
|
|
Enable USB host support on MX8MM Verdin.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Marcel Ziswiler <[email protected]>
Cc: Max Krummenacher <[email protected]>
Cc: Oleksandr Suvorov <[email protected]>
|
|
The iMX8M uses nop PHY, select PHY and NOP_PHY automatically.
Otherwise, the DM capable driver is now perfectly compatible.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
|
|
Fix cast from pointer to integer of different size by casting the
pointer to uintptr_t instead of uint32_t, the former has correct
size on both 32bit and 64bit architectures.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
|
|
Add new compatible string, used by some more up-to-date DTs.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
|
|
There is now multiple copies of CONFIG_MXC_USB_PORTSC in configs set to
PORT_PTS_UTMI | PORT_PTS_PTW, which is in fact the default register value
for MX6, MX7 and MX7ULP. Define the default value of CONFIG_MXC_USB_PORTSC
in the driver and use it in case CONFIG_MXC_USB_PORTSC is not defined in
config, to reduce the duplication.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
|
|
In case PHY support is enabled, use the generic EHCI PHY support
to start and stop the PHY.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
|
|
In case the platform uses DM, determine port number, which is
used as offset in USBMISC registers, from PHY node DT aliases,
just like Linux does.
Fixes: 4de51cc25b5 ("usb: ehci-mx6: Drop assignment of sequence number")
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
|
|
Instead of passing ad-hoc sequence number to usb_oc_config(), pass in
the USB MISC address itself. The USB MISC address comes from DT in DM
case, and from the old method using controller index in non-DM case.
Fixes: 4de51cc25b5 ("usb: ehci-mx6: Drop assignment of sequence number")
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
|
|
Split usb_power_config() per SoC and pass in USB PHY, USBNC and ANATOP
addresses instead of ad-hoc sequence numbers. This is only applicable
on legacy systems which do not implement proper PHY support. Once PHY
support is available, parts of this can be removed altogether and moved
to the PHY driver, similar to Linux phy-mxs-usb.c .
Fixes: 4de51cc25b5 ("usb: ehci-mx6: Drop assignment of sequence number")
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
|
|
Instead of passing ad-hoc index to USB PHY handling functions and then
try and figure out the PHY address, pass in the PHY address itself. For
DM case, this address comes easily from DT. For non-DM case, the previous
method is still present, however the non-DM case will soon be removed.
Fixes: 4de51cc25b5 ("usb: ehci-mx6: Drop assignment of sequence number")
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
|
|
In order to pass component addresses around easily instead of passing
ad-hoc sequence numbers, it is necessary to split ehci_mx6_common_init().
Make it so and call the separate functions instead.
Since board_ehci_hcd_init() makes no sense in DM case, do not call it
in DM case.
Fixes: 4de51cc25b5 ("usb: ehci-mx6: Drop assignment of sequence number")
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
|
|
In case DM and OF controler is enabled, but PHY support is disabled,
parse USB PHY and MISC component addresses from DT manually. Those
component addresses will be used in subsequent patches to access the
ANATOP, PHY and MISC registers matching the controller and thus get
rid of the ad-hoc controller sequence number mapping.
Fixes: 4de51cc25b5 ("usb: ehci-mx6: Drop assignment of sequence number")
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
|
|
Merge USBNC register layout structure into a single one, instead of
having three separate structures and a lot of ifdeffery. No functional
change.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
|
|
Add support for using DM clock framework to enable and disable all the
necessary clock for the USB controller.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
|
|
The driver turns on Vbus regulator in probe, but fails to turn it back
off in case of probe failure. Add the missing code.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
|
|
The driver is compatible with iMX8MN, add missing compatible string.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
|
|
The driver is compatible with iMX8MM, add missing compatible string.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
|
|
Add power domain nodes to DT.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
|
|
Add power domain nodes to DT.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
|
|
The fsl,usbphy DT property is deprecated, replace it with phys DT
property and specify #phy-cells, so that the generic PHY framework
can parse the PHY bindings without any extra hacking.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
|
|
The fsl,usbphy DT property is deprecated, replace it with phys DT
property and specify #phy-cells, so that the generic PHY framework
can parse the PHY bindings without any extra hacking.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
|
|
The standard compatible string is "usb-nop-xceiv", use it.
Note that keystone-k2g.dtsi already uses the aforementioned
compat string, so this patch can only remove the override.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Alexey Brodkin <[email protected]>
Cc: Eugeniy Paltsev <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Jean-Jacques Hiblot <[email protected]>
Cc: Murali Karicheri <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
|
|
The standard compatible string is "usb-nop-xceiv", use it.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Alexey Brodkin <[email protected]>
Cc: Eugeniy Paltsev <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Jean-Jacques Hiblot <[email protected]>
Cc: Murali Karicheri <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
|
|
The USB no-op PHY uses "usb-nop-xceiv" compatible string. This driver is
compatible with USB no-op PHY, so add the compatible string.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Alexey Brodkin <[email protected]>
Cc: Eugeniy Paltsev <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Jean-Jacques Hiblot <[email protected]>
Cc: Murali Karicheri <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
|
