| Age | Commit message (Collapse) | Author |
|---|
|
The register reflects lifecycle and some lifecycle-derived state of
i.MX95 has new offset address and layout, so display_life_cycle() is
added specifically for it.
Signed-off-by: Ye Li <[email protected]>
Signed-off-by: Alice Guo <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
|
|
Due to i.MX95 has reserved first 256MB DDR, change to use the DDR
start address in u-boot as the container header buffer.
Signed-off-by: Ye Li <[email protected]>
Signed-off-by: Alice Guo <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
|
|
Define the daisy register offset for i.MX94 at 0x608 within the iomuxc
register space. This enables correct pad selection for daisy chain
configuration on i.MX94 platforms.
Signed-off-by: Jacky Bai <[email protected]>
Signed-off-by: Alice Guo <[email protected]>
Acked-by: Peng Fan <[email protected]>
|
|
Extend get_imageset_end() to handle i.MX94 family.
Signed-off-by: Ye Li <[email protected]>
Signed-off-by: Jacky Bai <[email protected]>
Signed-off-by: Alice Guo <[email protected]>
Acked-by: Peng Fan <[email protected]>
|
|
i.MX94
- Add base addresses for WDG3, WDG4, GPIO6, and GPIO7 for i.MX94.
- Introduce common.h with macros of clock IDs, power domains, and CPU
types for platform-specific replacement (e.g., i.MX94, i.MX95).
- Extend imx_get_mac_from_fuse() to support i.MX94.
Signed-off-by: Ye Li <[email protected]>
Signed-off-by: Alice Guo <[email protected]>
Acked-by: Peng Fan <[email protected]>
Reviewed-by: Jacky Bai <[email protected]>
|
|
Update get_reset_reason() to support i.MX94 to send message to the
System Manager to retrieve the LM/system last booted/shutdown reasons.
Signed-off-by: Ye Li <[email protected]>
Signed-off-by: Alice Guo <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
|
|
reasons
System Manager provides the last booted and shutdown reasons of the
logical machines (LM) and system using the SCMI misc protocol (Protocol
ID: 0x84, Message ID: 0xA). This path adds get_reset_reason() to query
and print these reasons in SPL and U-Boot.
Signed-off-by: Peng Fan <[email protected]>
Signed-off-by: Alice Guo <[email protected]>
Reviewed-by: Ye Li <[email protected]>
|
|
Add a case for i.MX94 to return the correct string identifier in the
get_imx_type_str() function. This ensures proper CPU type reporting for
i.MX94 platforms.
Signed-off-by: Alice Guo <[email protected]>
|
|
Introduce support for the new i.MX94 processor, including its CPU type
and SoC-level Kconfig entry.
The i.MX94 is a new member of the i.MX9 family. It uses a System Manager
to handle system-level functions such as power, clock, sensor and pin
control. The System Manager runs on a Cortex-M processor, while the
Cortex-A processor communicates with it via the ARM SCMI protocol and a
messaging unit.
Signed-off-by: Ye Li <[email protected]>
Signed-off-by: Alice Guo <[email protected]>
Acked-by: Peng Fan <[email protected]>
Reviewed-by: Jacky Bai <[email protected]>
|
|
- Tighten some USB dependencies and remove some unused code.
|
|
Initialize mtd->writesize in nand_init() as otherwise
nand_page_size() returns 0 and this affects NAND read
operations.
Signed-off-by: Yegor Yefremov <[email protected]>
|
|
- Update MMC entry to match 'mmc' using 'N'
- Add myself as POWER maintainer for regulator and pmic patches. I have
started to handle relevant patches.
- Update QORIQ maintainer. Priyanka has moved to work on other stuff, I
have been handling this for quite some time.
Signed-off-by: Peng Fan <[email protected]>
|
|
Add myself as a maintainer of the NETWORK subsystem since:
- I have effectively been handling net patches in my patchwork queue and
sending pull requests to Tom,
- I do have push access to the u-boot-net custodian tree.
Also, add u-boot-net as the SCM tree for NETWORK (LWIP) since it is where
lwIP-related patches end up too.
Signed-off-by: Jerome Forissier <[email protected]>
CC: Ramon Fried <[email protected]>
CC: Joe Hershberger <[email protected]>
CC: Tom Rini <[email protected]>
|
|
RZG2 boot failure fix for boot with TFA which does not pass DT, and
R-Car Gen4 PCIe controller driver alignment with Linux fixes.
|
|
A few of the USB musb-new host glue drivers cannot build without access
to some platform specific header files. Express those requirements in
Kconfig as well.
Reviewed-by: Marek Vasut <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
A few of the USB host drivers cannot build without access to some
platform specific header files. Express those requirements in Kconfig as
well.
Reviewed-by: Marek Vasut <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
This driver was never enabled by any platforms after being added to the
tree over 5 years ago. Remove it.
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
This driver is unused since the removal of the bcm28155_ap board in
commit 0f6807e77b07 ("arm: Remove bcm28155_ap board"). Remove it.
Fixes: 0f6807e77b07 ("arm: Remove bcm28155_ap board")
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
This driver requires some mach-at91 specific header files in order to build.
Express that requirement in Kconfig as well.
Reviewed-by: Marek Vasut <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
A few of the platform specific DWC3 host glue drivers cannot build
without access to some platform specific header files. Express those
requirements in Kconfig as well.
Reviewed-by: Marek Vasut <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
R-Car V4H Reference Manual R19UH0186EJ0130 Rev.1.30 Apr. 21, 2025 page 585
Figure 9.3.2 Software Reset flow (B) indicates that for peripherals in HSC
domain, after reset has been asserted by writing a matching reset bit into
register SRCR, it is mandatory to wait 1ms.
Because it is the controller driver which can determine whether or not the
controller is in HSC domain based on its compatible string, add the missing
delay into the controller driver.
This 1ms delay is documented on R-Car V4H and V4M, it is currently unclear
whether S4 is affected as well. This patch does apply the extra delay on
R-Car S4 as well.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Assure the reset is latched and the core is ready for DBI access.
On R-Car V4H, the PCIe reset is asynchronized and does not take
effect immediately, but needs a short time to complete. In case
DBI access happens in that short time, that access generates an
SError. Make sure that condition can never happen, read back the
state of the reset which should turn the asynchronized reset into
synchronized one, and wait a little over 1ms to add additional
safety margin.
Signed-off-by: Marek Vasut <[email protected]>
|
|
R-Car V4H Reference Manual R19UH0186EJ0130 Rev.1.30 Apr. 21, 2025 page 4581
Figure 104.3b Initial Setting of PCIEC(example), third quarter of the figure
indicates that register 0xf8 should be polled until bit 18 becomes set to 1.
Register 0xf8 bit 18 is 0 immediately after write to PCIERSTCTRL1 and is set
to 1 in less than 1 ms afterward. The current readl_poll_timeout() break
condition is inverted and returns when register 0xf8 bit 18 is set to 0,
which in most cases means immediately. In case CONFIG_DEBUG_LOCK_ALLOC=y ,
the timing changes just enough for the first readl_poll_timeout() poll to
already read register 0xf8 bit 18 as 1 and afterward never read register
0xf8 bit 18 as 0, which leads to timeout and failure to start the PCIe
controller.
Fix this by inverting the poll condition to match the reference manual
initialization sequence.
Signed-off-by: Marek Vasut <[email protected]>
|
|
On the RZG2L platform, the advised
TF-A (https://github.com/renesas-rz/rzg_trusted-firmware-a/tree/v2.5/rzg2l)
does not pass any DTB blob to U-Boot.
On the other hand, the RZG2L part of U-Boot expects a DTB to be passed. It
means that if one flashes the latest TF-A as well as the mainline U-Boot,
it will crash trying to dereference the NULL DTB pointer before outputing
anything.
Check if the DTB pointer is NULL before trying to use it.
Signed-off-by: Mathieu Othacehe <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
This was apparently not built for several years: Since a2535243e011,
optee_copy_fdt_nodes implicitly works against the U-Boot dt. We
therefore have to tweak its reference before using the function and
restore things afterwards.
If it had been built, actually trying it out would have failed next: We
need CONFIG_OPTEE_LIB to actually build the function that is primarily
being tested here. And we need to re-initialize target fdt, now that the
tests may run in random order.
Fixes: a2535243e011 ("lib: optee: migration optee_copy_fdt_nodes for OF_LIVE support")
Fixes: ba2feaf41435 ("test: Split optee tests into three functions")
Signed-off-by: Jan Kiszka <[email protected]>
|
|
Signed-off-by: Jan Kiszka <[email protected]>
|
|
return is not a function, parentheses are not required
Signed-off-by: Osama Abdelkader <[email protected]>
|
|
The sandbox time offset is intended to be controlled via the U-Boot
environment, not the host process environment. Update os_get_time_offset()
to use env_get() instead of the libc getenv().
Leave other getenv() uses (e.g. U_BOOT_PERSISTENT_DATA_DIR,
UBOOT_SB_FUZZ_TEST) unchanged, since those refer to host environment
variables needed by sandbox tests.
Signed-off-by: Osama Abdelkader <[email protected]>
|
|
The android boot header is page aligned but the current code made the
assumption that the header was always smaller than the current header
format.
When the page_size is defined as 2048, as this is the case with the
cuttlefish target, the current code sets the end of the header in the
middle of it as the v3 and v4 headers are respectively 2112 and 2128
bytes long.
Fix that by aligning to page_size
Fixes: 1115027d2f75 ("android: boot: update android_image_get_data to support v3, v4")
Signed-off-by: Guillaume Ranquet <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-mmc into next
CI: https://source.denx.de/u-boot/custodians/u-boot-mmc/-/pipelines/27712
- Correct error value check in regulator_list_autoset
- Minor style fixes in mmc
|
|
Fix a couple of style issues reported by checkpatch.pl:
- Replace `#ifdef CONFIG_MMC_TRACE` with `#if IS_ENABLED(CONFIG_MMC_TRACE)`
to follow the preferred kernel style for config-dependent branches.
- Drop explicit zero initialization of a static variable.
No functional change intended.
Signed-off-by: Bhimeswararao Matsa <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
|
|
In regulator_list_autoset there is a test for ret being non-zero and
error being zero but it uses the binary '&' instead of the logical '&&'
which could well lead to unexpected results. Correct this to use the
logical '&&' instead.
This issue found by Smatch.
Signed-off-by: Andrew Goodbody <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
|
|
and fix related test/DTS issues""
This reverts commit 4d84fa1261eb27d57687f2e4c404a78b8653c183, reversing
changes made to b82a1fa7ddc7f3be2f3b75898d5dc44c34420bdd.
I had missed some feedback on this series from earlier, and we have
since had reports of regressions due to this as well. For now, revert
this.
Signed-off-by: Tom Rini <[email protected]>
|
|
Wadim Egorov <[email protected]> says:
First patch fixes boot issues with script boot method and the
second patch is a minor formatting fix in our board detection code.
@TI: I think the scriptaddr should be also updated for most TI/K3 and
beagle board boards.
Link: https://lore.kernel.org/r/[email protected]
|
|
The error message in phytec_get_product_name() was missing a newline,
causing log output to be concatenated with subsequent messages. Add
the newline to improve readability.
Signed-off-by: Wadim Egorov <[email protected]>
|
|
After switching our boards to standard boot, we observed that the
kernel hangs when booting with the "script" boot method over the
network.
The original scriptaddr value was copied from ti_common.env and
remained unused for some time. On phycore-am62x and phycore-am62ax,
however, this address conflicts with the current location where
ATF is loaded (CONFIG_K3_ATF_LOAD_ADDR).
Move scriptaddr to 0x89100000, directly after fdtoverlay_addr_r.
The phycore-am64x is not affected by this issue, but we update it
as well to keep all phycore-am6xx boards consistent.
Signed-off-by: Wadim Egorov <[email protected]>
Reviewed-by: Anshul Dalal <[email protected]>
|
|
related test/DTS issues"
Aristo Chen <[email protected]> says:
This patch series enhances FIT image robustness by adding **memory
region overlap detection** to `mkimage` and fixing existing overlaps
in DTS files and `binman` tests.
The primary goal is to prevent runtime memory corruption from
conflicting load addresses in FIT images.
Key Changes:
1. `mkimage` Overlap Detection: A new validation in
`tools/fit_image.c` checks for overlapping load addresses
within FIT configurations. `mkimage` now errors out with
detailed info on conflicts, preventing bad FIT image creation.
2. New Test Case: A Python test verifies the new detection.
It intentionally creates an overlap (kernel and FDT)
to confirm correct error handling.
3. Fixes for Existing Overlaps:
* Board DTS (k3-am6xx): Adjusted load addresses for TI
firmware stubs to prevent conflicts. This resolves
previously undetected overlaps.
* `binman` Tests: Fixed several tests. U-Boot load
addresses were shifted to avoid ATF conflicts. A new
linker script for TEE ELF sections ensures distinct
memory layouts.
4. Documentation: Added guidance for developers on how to
determine ELF load addresses using readelf, linker scripts,
and objdump when working with binman FIT images.
Impact:
This series improves FIT image reliability by catching overlaps
at build time, helping developers resolve issues before runtime
failures.
Link: https://lore.kernel.org/r/[email protected]
|
|
Add documentation to help users understand how to determine where ELF
files will be loaded when using binman's 'fit,load' property. This
addresses the common confusion about how load addresses are determined
from ELF files.
The documentation explains three methods:
1. Using readelf to examine program headers
2. Checking the linker script (.lds file)
3. Using objdump to see section addresses
Also includes a specific example from binman tests showing how
elf_sections.lds sets ATF load address to 0x00000010 and
elf_sections_tee.lds sets TEE load address to 0x00100010 to avoid
memory overlap conflicts.
This helps users debug memory layout conflicts more efficiently when
working with FIT images containing multiple ELF components.
Signed-off-by: Aristo Chen <[email protected]>
|
|
Add a new test case to verify that mkimage properly detects and reports
memory region overlaps in FIT image configurations.
The test creates a FIT image with kernel and FDT components that have
the same load address (0x40000), which should trigger the overlap
detection logic and cause mkimage to fail with an appropriate error
message.
Test verifies:
- mkimage returns non-zero exit code when overlap is detected
- Error message contains "Error: Overlap detected:"
- Error message identifies the specific overlapping components
(kernel@1 and fdt@1)
This test ensures the overlap detection feature works correctly and
prevents deployment of FIT images with conflicting memory layouts
that could cause runtime failures.
Signed-off-by: Aristo Chen <[email protected]>
|
|
This patch adds a validation step in mkimage to detect memory region
overlaps between images specified in the same configuration of a
FIT image. If any overlaps are found, the tool prints an error and
aborts the build.
This helps prevent runtime memory corruption caused by conflicting
load addresses between images.
Signed-off-by: Aristo Chen <[email protected]>
|
|
Fix memory overlaps in FIT image configurations for TI AM62x and AM64x
PHYCore and SK boards.
The overlaps occurred in two categories:
1. TI firmware stub images (tifsstub-hs, tifsstub-fs, tifsstub-gp):
These mutually exclusive firmware variants were incorrectly assigned
the same load address within FIT configurations, causing overlap
detection to fail. Adjust addresses with 64KB spacing:
- tifsstub-hs: Keep original address
- tifsstub-fs: Move to +64KB offset
- tifsstub-gp: Move to +128KB offset
2. Device tree overlay images (som-no-rtc, som-no-spi, som-no-eth):
These overlay files had insufficient spacing between load addresses,
causing actual memory overlaps. Increase spacing to 8KB boundaries
to accommodate overlay sizes safely.
An upcoming commit will validate if the memory region is overlapped
Signed-off-by: Aristo Chen <[email protected]>
|
|
Fix one binman test that has memory region overlap issue, the test case
needed to be updated to use non-overlapping memory layouts.
* Tests fixed:
- testFitSplitElf
* Changes made:
1. ELF section layouts: added elf_sections_tee.lds with different
address for TEE to avoid overlap with ATF address defined in
elf_sections.lds
2. Makefile to properly build elf_sections_tee binary
3. Updat ftest.py to use separate ELF files for TEE vs ATF components
in split-elf operations.
An upcoming commit will validate if the memory region is overlapped
Signed-off-by: Aristo Chen <[email protected]>
|
|
Fix three binman tests that has memory region overlap issue, the test
cases needed to be updated to use non-overlapping memory layouts.
* Tests fixed:
- testFitFirmwareLoadables
- testFitSignSimple
- testFitSignNoSignatureNodes
* Changes made:
Updated DTB test files to change U-Boot load addresses from 0x0 to
0x2000 to avoid overlapping with ATF in the 0x10-0xfc range:
- 276_fit_firmware_loadables.dts
- 340_fit_signature.dts
- 342_fit_signature.dts
An upcoming commit will validate if the memory region is overlapped
Signed-off-by: Aristo Chen <[email protected]>
Reviewed-by: Neha Malcom Francis <[email protected]>
|
|
Fix typo from `Singature` to `Signature`
Signed-off-by: Aristo Chen <[email protected]>
Reviewed-by: Dhruva Gole <[email protected]>
|
|
Add myself into the list for MbedTLS.
Signed-off-by: Raymond Mao <[email protected]>
Acked-by: Ilias Apalodimas <[email protected]>
|
|
Per a private email, drop Luka Perkov from MAINTAINERS entries.
Reviewed-by: Tony Dinh <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Prepare v2025.10-rc5
|
|
Signed-off-by: Tom Rini <[email protected]>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx into next
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/27684
- Add i.MX8 ahab-commit command.
- Add support for flashing board with UUU on imx93_frdm.
- Fix the acces of PFUZE100 regulator desc.
- Add more i.MX6 PWM clock definitions.
- Enable OP-TEE on phytec-imx8m and update documentation.
- Enable PCI host controller on iMX95 19x19 EVK.
[trini: Fixup spacing issues]
Signed-off-by: Tom Rini <[email protected]>
|
|
Use single make command for compiling blobs and U-Boot.
Update the imx firmware version.
Signed-off-by: Yannic Moog <[email protected]>
|
