| Age | Commit message (Collapse) | Author |
|---|
|
This patch adds the top level dtsi for AM6254atl SiP which integrates
the existing AM625 SoC with 512MiB of DDR in a single package.
More information about the package can be found here:
https://www.ti.com/lit/ds/symlink/am625sip.pdf
Signed-off-by: Anshul Dalal <[email protected]>
Reviewed-by: Bryan Brattlof <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Nishanth Menon <[email protected]>
[ upstream commit: 7c1d13a14e61ab33eec330cb6cabbddb37eecaa9 ]
(cherry picked from commit fa5a6a6e784bde78c6ec74eccd92d51fb9fd49e8)
|
|
The k3-am62x-sk-common dtsi represents the common hardware used across
am62x EVMs which can be configured with various DDR sizes or none (with
DDR integrated in the package) based on the specific am62x SoC used.
Therefore this patch moves the memory node and the SoC specific k3-am625
dtsi out of sk-common and into the board dts files. No functional change
is intended from this patch. The device-tree inheritance is changed as
follows:
Before:
k3-am62
^
k3-am625
^
k3-am62x-sk-common
^
am62x EVMs (k3-am625-sk, k3-am62-lp-sk)
After:
k3-am62
^
k3-am625 k3-am62x-sk-common
^ ^
am62x EVMs (k3-am625-sk, k3-am62-lp-sk)
Signed-off-by: Anshul Dalal <[email protected]>
Reviewed-by: Bryan Brattlof <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Nishanth Menon <[email protected]>
[ upstream commit: e0b9feca7329c495a76891d7766a781dea73787d ]
(cherry picked from commit 0b0edbbdf43bac6b28dd59c88647bd5e0b73ffea)
|
|
Add the label name 'reserved_memory' to the reserved-memory node in all
K3 AM6* board level dts files. This is done so that the node can be
referenced and extended to add more carveout entries as needed in future
refactoring patches.
Signed-off-by: Beleswar Padhi <[email protected]>
Acked-by: Andrew Davis <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Nishanth Menon <[email protected]>
[ upstream commit: 4f1aee4723a796a92f17b23699dc861b582ddfd2 ]
(cherry picked from commit 58c447fe500d78f5adc373b4945d8317e11df072)
|
|
TI's J784S4 SoC has two instances of PCIe Controller namely PCIe0 and
PCIe1 which are Cadence PCIe Controllers. Enable corresponding configs
to support PCIe Endpoint mode of operation on these instances.
Signed-off-by: Hrushikesh Salunke <[email protected]>
|
|
TI's J784S4 SoC has two instances of PCIe Controller namely PCIe0 and
PCIe1 which are Cadence PCIe Controllers. Add support to configure PCIe
instances in Endpoint mode of operation.
While at it disable all endpoint functions except function 0 during
probe to prevent the Root Complex from enumerating unconfigured
functions. This ensures only properly configured endpoint functions
are visible to the host and avoids enumeration issues with
multi-function devices.
Signed-off-by: Hrushikesh Salunke <[email protected]>
|
|
Probe the mux device early in the SERDES configuration flow to ensure
proper lane routing before PHY initialization. This is required for SoCs
where SERDES lanes can be muxed between different controllers
(PCIe, USB, etc), and different mux configurations are required between
different boot phases.
Signed-off-by: Hrushikesh Salunke <[email protected]>
|
|
Add a 1ms delay after powering on the PCIe power domain to ensure
the controller stabilizes before subsequent operations. This prevents
potential timing issues during PCIe endpoint initialization.
The delay allows sufficient time for the power domain to fully come
up and the hardware to be in a stable state before configuration
begins.
Signed-off-by: Hrushikesh Salunke <[email protected]>
|
|
Replace the board-specific implementation of do_board_detect()
with a call to the generic do_board_detect_am6() function to
avoid code duplication across AM6x family boards.
The generic function provides the same functionality with
additional fallback logic to try alternate EEPROM addresses.
Reviewed-by: Mattijs Korpershoek <[email protected]>
Signed-off-by: Guillaume La Roque (TI.com) <[email protected]>
|
|
Replace the board-specific implementation of do_board_detect() and
setup_serial() with calls to the generic do_board_detect_am6() and
setup_serial_am6() functions.
The generic function provides the same functionality with
additional fallback logic to try alternate EEPROM addresses.
Reviewed-by: Mattijs Korpershoek <[email protected]>
Signed-off-by: Guillaume La Roque (TI.com) <[email protected]>
|
|
I2C EEPROM data contains the board name and its revision.
Add support for:
- Reading EEPROM data and store a copy at end of SRAM
- Updating env variable with relevant board info
- Printing board info during boot
Use the generic do_board_detect_am6() and setup_serial_am6()
functions to avoid code duplication across AM6x family boards.
Reviewed-by: Mattijs Korpershoek <[email protected]>
Signed-off-by: Guillaume La Roque (TI.com) <[email protected]>
|
|
Add two new generic functions for AM6x family boards to simplify
board-specific implementations:
- do_board_detect_am6(): Generic board detection function that reads
the on-board EEPROM. It first attempts to read at the configured
address, and if that fails, tries the alternate address
(CONFIG_EEPROM_CHIP_ADDRESS + 1). This provides a common
implementation that can be used across different AM6x boards.
- setup_serial_am6(): Sets up the serial number environment variable
from the EEPROM data. The serial number is converted from
hexadecimal string format to a 16-character hexadecimal
representation and stored in the "serial#" environment variable.
Both functions are protected by CONFIG_IS_ENABLED(TI_I2C_BOARD_DETECT)
and are designed to be used by AM62x, AM64x, AM65x, and other AM6x
family boards.
Reviewed-by: Mattijs Korpershoek <[email protected]>
Signed-off-by: Guillaume La Roque (TI.com) <[email protected]>
|
|
This patch enable spinand flashes support for en7523 based boards
Signed-off-by: Mikhail Kshevetskiy <[email protected]>
|
|
This patch adds spinand flashes support to en7523 dts
Signed-off-by: Mikhail Kshevetskiy <[email protected]>
|
|
This patch activates ethernet controller support for en7523 based boards
Signed-off-by: Mikhail Kshevetskiy <[email protected]>
|
|
This patch adds integrated ethernet controller support to en7523 dts
Signed-off-by: Mikhail Kshevetskiy <[email protected]>
|
|
Add support for Ethernet controller present in Airoha en7523/en7529/en7562.
Signed-off-by: Mikhail Kshevetskiy <[email protected]>
|
|
This allow us remove some an7581/an7583 specific code and use a common
code instead.
Signed-off-by: Mikhail Kshevetskiy <[email protected]>
|
|
This patch activates reset controller support for en7523 based boards
Signed-off-by: Mikhail Kshevetskiy <[email protected]>
|
|
This patch adds reset controller support to en7523 dts
Signed-off-by: Mikhail Kshevetskiy <[email protected]>
|
|
This adds reset controller support for airoha en7523/en7529/en7562 SoCs.
Signed-off-by: Mikhail Kshevetskiy <[email protected]>
|
|
Introduce reset capability for EN7523 device-tree binding
Signed-off-by: Mikhail Kshevetskiy <[email protected]>
|
|
This patch unify probing code using airoha SCU regmap helper, thus a
common function can be used instead of an7581/an7583 specific ones.
Signed-off-by: Mikhail Kshevetskiy <[email protected]>
|
|
In preparation for support for Airoha AN7583, convert the driver to
regmap API. This is needed as Airoha AN7583 will use syscon to access
reset registers.
Signed-off-by: Christian Marangi <[email protected]>
|
|
This patch activates clk support for en7523 based boards
Signed-off-by: Mikhail Kshevetskiy <[email protected]>
|
|
This adds clock driver for airoha en7523/en7529/en7562 SoCs. The code
is based on corresponding linux driver.
Signed-off-by: Mikhail Kshevetskiy <[email protected]>
|
|
Use common helper to get CHIP_SCU registers.
Signed-off-by: Mikhail Kshevetskiy <[email protected]>
|
|
We need access SCU and CHIP_SCU regmaps in several places (clk-airoha,
reset-airoha, airoha_eth). Unfortunately these regmaps can't be easily
retrieved with a common code, because of different Airoha SoCs uses
a different dts structure.
To make life easy we can write a commonly named SoC specific helpers
for these tasks. This patch implements helpers for Airoha EN7523 SoC.
Signed-off-by: Mikhail Kshevetskiy <[email protected]>
|
|
We need access SCU and CHIP_SCU regmaps in several places (clk-airoha,
reset-airoha, airoha_eth). Unfortunately these regmaps can't be easily
retrieved with a common code, because of different Airoha SoCs uses
a different dts structure.
To make life easy we can write a commonly named SoC specific helpers
for these tasks. This patch implements helpers for Airoha AN7581 SoC.
Signed-off-by: Mikhail Kshevetskiy <[email protected]>
|
|
Basic support for en7523/en7529/en7562 SoCs. Within a patch
only serial console will be supported.
Signed-off-by: Mikhail Kshevetskiy <[email protected]>
|
|
This is required because airoha/en7523 will be added with the following
patches. Without this line config for en7523 will be created instead of
an7581.
Signed-off-by: Mikhail Kshevetskiy <[email protected]>
|
|
%s/to be write/to write/
Signed-off-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
%s/private date/private data/
Signed-off-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
%s/v1.0 complaint/v1.0 compliant/
Signed-off-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
%s/to be write/to be written/
%s/writen/written/
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
Clean up the sound Kconfig options to let all sound devices depend on
CONFIG_SOUND.
Before this patch it was possible to select CONFIG_SOUND_MAX98357A even
with CONFIG_SOUND=n.
Signed-off-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Update the resource management configuration (rm-cfg.yaml) to align
with the default configuration provided in TI's AM62xx Processor SDK
Linux version 11.01.05.03, generated using the K3 Resource Partitioning
Tool.
This matches the configuration from board/ti/am62x/rm-cfg.yaml and the
notable change is the sharing of MCU GPIO interrupts between DM R5 and
A53 cores, and reservation of an additional virtual interrupt and event
for TIFS usage.
Signed-off-by: Vitor Soares <[email protected]>
Reviewed-by: Francesco Dolcini <[email protected]>
Reviewed-by: Anshul Dalal <[email protected]>
|
|
If missing, lbaint_t typedef will not be found in some cases.
[The proper fix for the commit above at the time would have been to
include ide.h as only since commit 1a73661bc7a7 ("dm: Add a new header
for block devices") is the typedef in blk.h]
Fixes: 04735e9c5578 ("Fix ext2/ext4 filesystem accesses beyond 2TiB")
Signed-off-by: Quentin Schulz <[email protected]>
|
|
The general python documentation for the subprocess class recommends
that run() be used in all cases that it can handle. What we do in
RunAndLog is simple enough that run() is easy to switch to. In fact,
looking at this exposed a problem we have today, which is that we had
combined stdout and stderr but then looked at both stdout and stderr as
if they were separate. Stop combining them.
Signed-off-by: Tom Rini <[email protected]>
|
|
instead of depends on"
Quentin Schulz <[email protected]> says:
This improves readability in menuconfig by putting PWM symbols under a
Kconfig menu.
It also groups PWM symbols that depend on DM_PWM together under an if
DM_PWM block so that we don't need to always list the dependency in the
depends on of the symbol.
No intended change in behavior except how it shows in menuconfig.
Link: https://lore.kernel.org/r/[email protected]
|
|
Reviewed-by: Tom Rini <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
|
|
This simplifies the "depends on" since we don't need DM_PWM listed
explicitly there as it already is made explicit via the surrounding
"if". No intended change in behavior.
Reviewed-by: Tom Rini <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
|
|
Since it is registered as a U_CLASS_DRIVER, Sandbox PWM driver is a
Driver Model Driver and thus to be usable depends on DM_PWM to be
selected.
Let's make sure of that via the appropriate Kconfig option.
Signed-off-by: Quentin Schulz <[email protected]>
|
|
So it's visually better split from the other subsystems when using
menuconfig.
Reviewed-by: Tom Rini <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
|
|
Add support for R-Car Gen5 SoCs into the driver.
The default quirk is identical to previous generation.
Signed-off-by: Hai Pham <[email protected]>
Signed-off-by: Marek Vasut <[email protected]> # Tweak commit message
|
|
Some shared memory mailboxes may have empty receive operation,
because the data are polled by upper layers directly from the
shared memory region, and there is no completion interrupt or
bit of any sort. Allow empty .recv callback, and if the .recv
callback is empty, exit from mbox_recv() right away, because
any polling for completion here would be meaningless.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Alice Guo <[email protected]>
|
|
Isolate Renesas R-Car Gen3 clock driver to R-Car Gen3 and Gen4 and RZ/G2L.
The Renesas R-Car Gen5 uses SCMI clock protocol driver instead. This is
a preparatory change for R-Car Gen5. No functional change.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Resync all defconfig files using qconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-dfu
u-boot-dfu-20251107:
CI: https://source.denx.de/u-boot/custodians/u-boot-dfu/-/pipelines/28223
Android:
* Add bootargs environment to kernel commandline
DFU:
* Support DFU over PCIe in SPL
|
|
https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request efi-2026-01-rc2
CI: https://source.denx.de/u-boot/custodians/u-boot-efi/-/pipelines/28208
Documentation:
* bootstd: Describe environment variable extension_overlay_addr
environment and remove extension support from TODO list
EFI:
* Correct the detection of the video mode in the EFI payload app:
- Use struct efi_gop_mode_info in the definition of struct
efi_entry_gopmode.
- In function get_mode_from_entry() use the correct type for the video
mode structure.
* Use a valid error code as return value in efi_store_memory_map().
* Avoid a memory leak for the variable name in efi_bl_create_block_device().
* Correct the code indentation in efi_uc_stop().
* Correct the description of struct efi_priv.
* Fix typos in code comments.
Other:
* qfw: Add more fields and a heading to qfw list
* Fix the support for ACPI pass-through on ARM and RISC-V:
Avoid zeroing out the XSDT address
* test: provide unit test for 'acpi list' command
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEbcT5xx8ppvoGt20zxIHbvCwFGsQFAmkNj/kACgkQxIHbvCwF
# GsS8NQ/6Aj+Z54HJTIEfoXssvElLr5ATactrCxszq42i/yy6dLqa2Ym1afG6w1XS
# 1ZbCeU/bCXFke5Tsz+x89gEfckUm83oTwngwcID0WR1qn8mWjwR7tM5MuORq8NxU
# 7NwLuFs9O/QZihagKdz6hv1/Y+cBwiAYLY16EYVSuUlbLaKQo3QvxwWkqG3jdKWV
# Rm58/PolU+2h04MBwP0SxSduX4OyRF/tMOGjf5RGLyqCyj8kIgdu7PvUAPMM+Gps
# KemL59V0Bdv8hlF4JknmPz+idtZg2nHIDdNrBZvoxwzwGQeRZ1YXAMruRxZXqDYL
# tiuDp6HMv/GfIIGkz14tJtJMdboaAybAnluPWGalx8JQJqJzEPww0R+9s4KKQeWL
# mHgRyl6PxVV9p19f79Qq6q6ETwrFDX0YH3pdrGUk3DBa3lDt0UsEAnuW4FvaJ8tx
# 3PMrjKAxpxocT0hglsMVnptnfvDEigMsjwH/TWrau83mY+juxFQLjm+U4vye+qCa
# 4zXjjLas18+eRcrv2KxU7teakyi1Jp+WbqHq37L26YcQMaLq/RkBc0bTrsreKKLu
# jprYFpvc7EJpH2Fd1XWaZ2EnxXcVSJSvrY/iwRQqb6wbwQ6XGtMvSh3IFY8IzAoh
# N2Pj78oaYqyL1q/TftuZWhEHo3a0M/HfM4D+oMSHzJtWCb0wZHE=
# =OGcS
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 07 Nov 2025 12:21:45 AM CST
# gpg: using RSA key 6DC4F9C71F29A6FA06B76D33C481DBBC2C051AC4
# gpg: Good signature from "Heinrich Schuchardt <[email protected]>" [unknown]
# gpg: aka "[jpeg image of size 1389]" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 6DC4 F9C7 1F29 A6FA 06B7 6D33 C481 DBBC 2C05 1AC4
|
|
https://source.denx.de/u-boot/custodians/u-boot-mmc
CI: https://source.denx.de/u-boot/custodians/u-boot-mmc/-/pipelines/28218
- Disabling FMP on Exynos850 to make eMMC functional when U-Boot is
executed during USB boot
- Drop extra included errno.h
|
