| Age | Commit message (Collapse) | Author |
|---|
|
The third_arg for a dfu alt is read as an integer and is overloaded for
different supported backends. For ext4 and fat, this third_arg
represents the partition and forms the dev part string, which should
have its partition in hex. This commit fixes dfu ext4/fat usage for
devices with ten or more partitions.
Signed-off-by: Ivan Pang <[email protected]>
Reviewed-by: Mattijs Korpershoek <[email protected]>
Reviewed-by: Lukasz Majewski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mattijs Korpershoek <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-raspberrypi
Updates for RPi for 2025.07-rc5:
- configs: rpi: set NR_DRAM_BANKS to 8 to accommodate RAM on 16GB models
|
|
Writing to eMMC on RK3528 is affected with the same or a similar issue
as on RK3588, where eMMC must init to HS200 at least once to fully work.
Trying to write u-boot-rockchip.bin to eMMC fails with:
=> mmc write $fileaddr 40 5000
MMC write: dev # 0, block # 64, count 20480 ... mmc write failed
0 blocks written: ERROR
For U-Boot to enable HS200 mode the mmc-hs200-1_8v prop must be defined
in the device tree. Linux does not seem to be affected and is able to
detect and use HS200 without this prop.
Enable use of HS200 and fix eMMC write on RK3528 by adding the missing
mmc-hs200-1_8v prop for affected boards:
=> mmc write $fileaddr 40 5000
MMC write: dev # 0, block # 64, count 20480 ... 20480 blocks written: OK
Fixes: b112a44531cb ("board: rockchip: Add minimal generic RK3528 board")
Fixes: ccbddf645310 ("board: rockchip: Add Radxa E20C")
Signed-off-by: Jonas Karlman <[email protected]>
|
|
Raspberry Pi 5 can now have up to 16 GiB of RAM where the memory spans 8
DRAM banks in total. Increase the config value to 8 to initialize the
whole RAM. Without this change, kernel only sees 8 GiB of RAM on the 16
GiB CM5 as reported in [1].
[1] https://github.com/home-assistant/operating-system/issues/3989
Signed-off-by: Jan Čermák <[email protected]>
Reviewed-by: Matthias Brugger <[email protected]>
|
|
6.15 + winbond"
Christian Marangi <[email protected]> says:
This small series sync linux/bitfield.h from Linux 6.15 and fix all
the compilation error due to a change in the header include.
The sync is needed to make it easier to support the winbond changes.
The changes are CI test with [1]
[1] https://github.com/u-boot/u-boot/pull/777
Link: https://lore.kernel.org/r/[email protected]
|
|
Add Winbond W25N04KV flash support that use a different value to detect
ECC bitflip.
Signed-off-by: Christian Marangi <[email protected]>
|
|
Sync bitfield.h header with Linux 6.15 version. Mainly is to permit the
introduction of FIELD_PREP_CONST. The bug.h header changed to
build_bug.h doesn't cause any regression as we also ship split header
similar to how it's done with in Linux.
Signed-off-by: Christian Marangi <[email protected]>
|
|
The GENMASK/GENMASK_ULL macro requires inclusion of linux/bitops.h
header. It does currently work as bitfield.h includes it indirectly
but this will change when bitfield.h will be synced with new Linux
version.
Also raw printf require linux/bug.h header (also currently included
indirectly by bitfield.h)
Explicitly include the headers to fix future compilation error.
Signed-off-by: Christian Marangi <[email protected]>
|
|
The WARN macro requires inclusion of linux/bug.h header. It does
currently work as bitfield.h includes it indirectly but this will
change when bitfield.h will be synced with new Linux version.
Explicitly include the header to fix future compilation error.
Signed-off-by: Christian Marangi <[email protected]>
|
|
The WARN macro requires inclusion of linux/bug.h header. It does
currently work as bitfield.h includes it indirectly but this will
change when bitfield.h will be synced with new Linux version.
Explicitly include the header to fix future compilation error.
Signed-off-by: Christian Marangi <[email protected]>
|
|
E Shattow <[email protected]> says:
Make consistent use of lowercase hexadecimal prefix '0x' throughout U-Boot.
There are a few remaining uses of uppercase 'X' to denote hexadecimal prefix
or placeholder in documentation and error messages.
External devicetree-rebasing dts/upstream and the generated code of
xilinx/zynq are ignored for the series.
Link: https://lore.kernel.org/r/[email protected]
|
|
Use consistent lowercase hex prefix style in include/*
Signed-off-by: E Shattow <[email protected]>
|
|
Use consistent lowercase hex prefix style in arch/*
Signed-off-by: E Shattow <[email protected]>
|
|
Use consistent lowercase hex prefix style in lib/*
Signed-off-by: E Shattow <[email protected]>
|
|
Use consistent lowercase hex prefix style in tools/*
Signed-off-by: E Shattow <[email protected]>
|
|
Use consistent lowercase hex prefix style in drivers/*
Does not change hex prefix case in allcaps uppercase style error messages
Signed-off-by: E Shattow <[email protected]>
|
|
Use consistent lowercase hex prefix style in board/*
Does not change auto-generated files in xilinx/zynq/*/ps7_init_gpl.c
Signed-off-by: E Shattow <[email protected]>
|
|
Use consistent lowercase hex prefix style in configs/*
Signed-off-by: E Shattow <[email protected]>
|
|
Rasmus Villemoes <[email protected]> says:
There's really no reason for the gd pointer to have the volatile
qualifier.
In fact, I claim that it's completely unnecessary and just pessimizes
code generation and forces ugly casts in lots of places. For example,
see the casts in drivers/core/tag.c where elements are added to
gd->dm_taglist, or a helper such as cyclic_get_list() that should not
be needed.
Also, it is what ends up standing in the way of an otherwise
innocent code cleanup of list.h:
https://lore.kernel.org/u-boot/20250522165656.GB2179216@bill-the-cat/
Note that riscv, x86 as well as arm64 with LTO enabled has not had
this volatile qualifier, so it's unlikely there's any generic code
that depends on it.
Link: https://lore.kernel.org/r/[email protected]
|
|
It's slightly ironic that riscv at very first had the gd pointer
volatile qualified [6020faf62c3 ("riscv: nx25: include: Add header
files to support RISC-V")], removed that back in 2018
[40717eb849c ("riscv: checkpatch: Fix use of volatile")], and then in
2020 this helper was added [6b9966e1aa3 ("riscv: define function
set_gd()")] which needlessly had volatile in the prototype.
Signed-off-by: Rasmus Villemoes <[email protected]>
|
|
The global gd pointer is no longer volatile-qualified. Callers of this
helper function have been updated to no longer use volatile-qualifed
temporary variables, so update the prototype accordingly.
Signed-off-by: Rasmus Villemoes <[email protected]>
|
|
The global gd pointer is no longer volatile-qualified, so drop that
qualifier from these bookkeeping variables.
Signed-off-by: Rasmus Villemoes <[email protected]>
|
|
The global gd pointer is no longer volatile-qualified, so drop that
qualifier from these bookkeeping variables.
Signed-off-by: Rasmus Villemoes <[email protected]>
Reviewed-by: Heinrich Schuchardt <[email protected]>
|
|
Now that the global gd pointer is no longer volatile-qualified,
there's no reason for the temporary variables used for
saving/restoring it to have that qualifier.
Signed-off-by: Rasmus Villemoes <[email protected]>
Tested-by: Anshul Dalal <[email protected]>
|
|
Signed-off-by: Rasmus Villemoes <[email protected]>
|
|
The way DECLARE_GLOBAL_DATA_PTR is used, the stuff under #if 0 can
never compile as you cannot have a non-constant initializer at global
scope (and one would get linker errors as well because the 'gd' symbol
would be defined in multiple TUs).
Signed-off-by: Rasmus Villemoes <[email protected]>
Acked-by: Angelo Dureghello <[email protected]>
|
|
Signed-off-by: Rasmus Villemoes <[email protected]>
|
|
Signed-off-by: Rasmus Villemoes <[email protected]>
|
|
Signed-off-by: Rasmus Villemoes <[email protected]>
|
|
Signed-off-by: Rasmus Villemoes <[email protected]>
|
|
There's a bunch of other places where this qualifier should be
dropped, e.g. in the set_gd() prototype and for various variables used
for stashing the value in the mach-imx/ directory and elsewhere. But
that will be done in follow-up patches.
Signed-off-by: Rasmus Villemoes <[email protected]>
Tested-by: Anshul Dalal <[email protected]>
|
|
This patch is to solve the sandbox building error:
$ make O=build-sandbox -s sandbox_defconfig
$ make O=build-sandbox -s -j2
/usr/bin/ld: /tmp/u-boot.27rzOu.ltrans58.ltrans.o: undefined reference to symbol 'pthread_kill@@GLIBC_2.2.5'
/usr/bin/ld: /lib/x86_64-linux-gnu/libpthread.so.0: error adding symbols: DSO missing from command line
collect2: error: ld returned 1 exit status
[...]
Fixes: b989f9ed9fe1 ("test: lib: add initjmp() test")
Signed-off-by: Raymond Mao <[email protected]>
Reviewed-by: Jerome Forissier <[email protected]>
Tested-by: Patrice Chotard <[email protected]>
|
|
This function is currently a misnomer at times as we have cases where it
passes arguments to the image. In preparation for making that be a more
common case rename this function to jump_to_image(...). In order to do
this, rename jump_to_image in board_init_r(...) to jumper so that we do
not have a conflict.
Signed-off-by: Simon Glass <[email protected]>
[trini: Reword the commit message, adding missing cases of
jump_to_image_no_args()]
Signed-off-by: Tom Rini <[email protected]>
|
|
Move this so we can include it from sandbox, needed since it is in a
bloblist and must have a check.
Signed-off-by: Simon Glass <[email protected]>
|
|
Sukrut Bellary <[email protected]> says:
This patch series adds the support for
1. In am33xx SoC[1], enhanced capture (eCAP) supports auxiliary PWM (APWM).
This series adds the PWM driver support for the APWM feature for eCAP on
AM33xx. AM335X_ECAP0_IN_PWM0_OUT is used to enable the backlight.
2. Fix build warning in ti-ehrpwm driver in dev_deb().
3. Enable eCAP0 PWM and LCD pin muxing to support splash screen on
AM335x EVM[2].
[1] AM335x TRM - https://www.ti.com/lit/ug/spruh73q/spruh73q.pdf
[2] AM335x EVM - https://www.ti.com/tool/TMDXEVM3358
per discussion on the earlier patch series,
https://lore.kernel.org/all/[email protected]/
dropping the device tree changes in this series due to OF_UPSTREAM
conflict.
As we are dropping the DT patch, started with the new series instead of
V2.
This series doesn't contain defconfig changes since we don't want to
enable LCD, splash screen and PWM support by default.
Enabling splash screen and PWM support in defconfig causes u-boot crash
on AM335x based beaglebone black. This will be handled in a separate
patch.
Link: https://lore.kernel.org/r/[email protected]
|
|
On AM335x EVM[1],
1. pin AM335X_ECAP0_IN_PWM0_OUT is used to enable the
backlight. ECAP0 can be configured in single channel PWM mode.
If CONFIG_PWM_TI_ECAP is enabled, perform eCAP0 pin muxing.
2. Pins LCD_DATA0 - LCD_DATA15, gpmc_ad8 - gpmc_ad15 and
lcd_vsync, lcd_sync, lcd_ac_bias_en, lcd_pclk are used for driving LCD.
If CONFIG_AM335X_LCD is enabled, perform the LCD pin muxing.
This is required to enable splash screen support on AM335x EVM.
[1] AM335x EVM - https://www.ti.com/tool/TMDXEVM3358
Signed-off-by: Sukrut Bellary <[email protected]>
|
|
If CONFIG_PWM_TI_EHRPWM is enabled, it throws the build warning in
dev_dbg() due to incorrect format specifier as,
"warning: format ‘%lx’ expects argument of type ‘long unsigned int’, but
argument 4 has type ‘fdt_addr_t’ {aka ‘unsigned int’}".
Fix this with the correct format specifier.
Signed-off-by: Sukrut Bellary <[email protected]>
|
|
In am33xx SoC[1], enhanced capture (eCAP) supports auxiliary PWM (APWM).
This series adds the PWM driver support for the APWM feature for eCAP on
AM33xx.
eCAP HW also supports the capture mode. Currently, this driver only
supports APWM.
This is based on the Linux kernel driver -> drivers/pwm/pwm-tiecap.c
Version: v6.12
Tested on AM335x EVM[2].
[1] AM335x TRM - https://www.ti.com/lit/ug/spruh73q/spruh73q.pdf
[2] AM335x EVM - https://www.ti.com/tool/TMDXEVM3358
Signed-off-by: Sukrut Bellary <[email protected]>
|
|
RAM drivers using Device Model currently lack of their own Kconfig menu
entry, which makes Kconfig put all options of the class in the top-level
menu of device drivers. These options are also incorrectly grouped with
pinctrl options in the generated .config, which is hard to read. Let's
create a menu entry for these drivers.
Fixes: 6c51df6859f ("dm: Add support for RAM drivers")
Signed-off-by: Yao Zi <[email protected]>
Reviewed-by: Quentin Schulz <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Fix typo from heder to header
Signed-off-by: Aristo Chen <[email protected]>
|
|
Although if we don't setup an initrd, there could be a stale initrd
setting from the previous boot firmware in the live device tree. So,
make sure there is no setting left if we don't want an initrd.
This can happen when booting on a Raspberry Pi. The boot firmware can
happily load an initrd before us and configuring the addresses in the
live device tree we get handed over.
Especially the setting `auto_initramfs` in config.txt is dangerous.
When enabled (default), the firmware tries to be smart and looks for
initramfs files.
Signed-off-by: Richard Weinberger <[email protected]>
|
|
Use lbaint_t for blknr to avoid overflow in ext4fs_read_file().
Background:
blknr (block number) used in ext4fs_read_file() could be increased to a
very large value and causes a wrap around at 32 bit signed integer max,
thus becomes negative. This results in an out-of-normal range for sector
number (during the assignment delayed_start = blknr) where delayed_start
sector is typed uint64 lbaint_t. This causes the "Read outside partition"
error.
Looks like we also have this overflown problem in ext4_write.c that needs
to be addressed.
This patch was tested on the Synology DS116 (Armada 385) board, and a
4TB Seagate HDD.
Signed-off-by: Tony Dinh <[email protected]>
|
|
Some SoCs require a Trusted Firmware-A (TF-A) AP Trusted ROM (BL1) to
initialize the SoC before U-Boot can run properly. Add an atf-bl1 etype
so we can properly package BL1 into a final binary
Signed-off-by: Bryan Brattlof <[email protected]>
Acked-by: Simon Glass <[email protected]>
|
|
Call do_board_detect() hook before the K3 DDRSS driver gets probed.
It will allow boards to adjust DDR timings in do_board_detect().
Signed-off-by: Emanuele Ghidoli <[email protected]>
|
|
If an Unexpected exception is thrown in a test, an undefined variable
error is reported. Fix this.
Signed-off-by: Simon Glass <[email protected]>
Fixes: 85d7dae377a ("test: Detect dead connections")
Reviewed-by: Mattijs Korpershoek <[email protected]>
|
|
If a BootFail exception is thrown in a test, it is not handled
correctly. Use the correct fixture variable 'ubman_fix' to resolve this.
Signed-off-by: Simon Glass <[email protected]>
Fixes: d9ed4b75add ("test/py: Drop u_boot_ prefix on test files")
Reviewed-by: Mattijs Korpershoek <[email protected]>
|
|
When the toradex-smarc-imx8mp_defconfig file was first added, SPL_STACK
was set to 0x960000, but SPL_HAVE_INIT_STACK wasn't enabled.
This led to SPL_STACK being correctly dropped in commit 25fefa05d732
("configs: Resync with savedefconfig"), since SPL_HAVE_INIT_STACK was
missing, which ended up making the board not boot.
Fix this by adding SPL_STACK back and making sure SPL_HAVE_INIT_STACK is
enabled.
Fixes: dde53eae88d6 ("board: toradex: add Toradex SMARC iMX8MP")
Signed-off-by: Hiago De Franco <[email protected]>
Acked-by: Francesco Dolcini <[email protected]>
|
|
After enabling some options to support EEPROM read in SPL
(CONFIG_SPL_I2C_EEPROM), the following error appears:
alloc space exhausted
Increasing SYS_MALLOC_F_LEN from 8kB to 64kB fixes the problem.
But instead of manually increasing the value, adopt method used in
commit ce3f23404c19 ("board: bsh: imx8mn_bsh_smm_s2/s2pro: enlarge
CONFIG_SPL_SYS_MALLOC_F_LEN"):
Dropping CONFIG_SPL_SYS_MALLOC_F_LEN option allows it to be set to the
default value of CONFIG_SYS_MALLOC_F_LEN, which is set by default to 64kB
(0x10000) on i.MX8M platforms.
Suggested-by: Fabio Estevam <[email protected]>
Signed-off-by: Hugo Villeneuve <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
i.MX91 device tree still not landed in linux kernel, so drop OF_UPSTREAM
and move the device tree files to arch/arm/dts
Signed-off-by: Peng Fan <[email protected]>
Reviewed-by: Sumit Garg <[email protected]>
|
|
When doing the investigation for commit 53bb8fdea12a ("mmc: Kconfig:
Correct dependencies SDHCI ADMA options") I missed the implications of
MMC_SDHCI_ADMA_HELPERS. The problem is that FSL_ESDHC via the
FSL_ESDHC_SUPPORT_ADMA2 option will also enable these helper functions.
This in turn means the correct dependency here is
MMC_SDHCI_ADMA_HELPERS and not *MMC_SDHCI_ADMA.
Reported-by: Heiko Thiery <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
