| Age | Commit message (Collapse) | Author |
|---|
|
https://source.denx.de/u-boot/custodians/u-boot-fsl-qoriq
CI: https://source.denx.de/u-boot/custodians/u-boot-fsl-qoriq/-/pipelines/23856
- Use strcat to replace sprintf for t208xqds
- Fix bootefi for board ls1028a
- Various fixes to sl28 board
|
|
https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request doc-2025-01-rc5
Documentation:
* sending_patches: Fix spelling of "its"
* environment: NET_LWIP dhcp sets ipaddrN, netmaskN and gatewayipN
* remove redundant Rockchip bindings
* fwu_updates: Fix formatting
* coolpi: Fix document style
* board: theobroma-systems: fix feature list in introductions
Fix typos in code comments:
* clk: mpc83xx: Fix typo in "Coherent System Bus"
* efi_loader: Fix typos in enum efi_allocate_type
|
|
buf was used as destination and as parameter to sprintf
which triggers an undefined behaviour.
This commit removes this usage of sprintf and uses strcat
to append strings to buf variable.
Signed-off-by: Francois Berder <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
|
|
Without this patch, there will be error indicating that
"Cannot use 64 bit addresses with SDMA", and the booting
process will stuck.
please see full boot log below
U-Boot 2022.04-g18185931 (Sep 11 2024 - 13:15:30 +0800)
SoC: LS1028AE Rev1.0 (0x870b0010)
Clock Configuration:
CPU0(A72):1500 MHz CPU1(A72):1500 MHz
Bus: 400 MHz DDR: 1600 MT/s
Reset Configuration Word (RCW):
00000000: 3c004010 00000030 00000000 00000000
00000010: 00000000 018f0000 0030c000 00000000
00000020: 020031a0 00002580 00000000 00003296
00000030: 00000000 00000010 00000000 00000000
00000040: 00000000 00000000 00000000 00000000
00000050: 00000000 00000000 00000000 00000000
00000060: 00000000 00000000 200e705a 00000000
00000070: bb580000 00000000
Model: LS1028A RDB Board
Board: LS1028AE Rev1.0-RDB, Version: C, boot from SD
FPGA: v8 (RDB)
SERDES1 Reference : Clock1 = 100.00MHz Clock2 = 100.00MHz
DRAM: 3.9 GiB
DDR 3.9 GiB (DDR4, 32-bit, CL=11, ECC on)
Using SERDES1 Protocol: 47960 (0xbb58)
PCIe1: pcie@3400000 Root Complex: no link
PCIe2: pcie@3500000 Root Complex: x1 gen2
Core: 45 devices, 22 uclasses, devicetree: separate
WDT: Started watchdog@c000000 with servicing (60s timeout)
WDT: Started watchdog@c010000 with servicing (60s timeout)
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment
EEPROM: Invalid ID (ff ff ff ff)
In: serial
Out: serial
Err: serial
SEC0: RNG instantiated
Net:
Warning: enetc-0 (eth0) using random MAC address - d2:9b:a5:37:7b:b5
eth0: enetc-0
Warning: enetc-2 (eth1) using random MAC address - ca:57:11:de:de:cb
, eth1: enetc-2, eth2: swp0, eth3: swp1, eth4: swp2, eth5: swp3
Hit any key to stop autoboot: 0
Trying load HDP firmware from SD..
switch to partitions #0, OK
mmc0 is current device
Device: FSL_SDHC
Manufacturer ID: 9f
OEM: 5449
Name: SD32G
Bus Speed: 50000000
Mode: SD High Speed (50MHz)
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 28.9 GiB
Bus Width: 4-bit
Erase Group Size: 512 Bytes
MMC read: dev # 0, block # 18944, count 512 ... 512 blocks read: OK
Loading hdp firmware from 0x00000000a0000000 offset 0x0000000000002000
Loading hdp firmware Complete
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
** Unable to read file / **
Failed to load '/'
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
Scanning disk [email protected]...
Scanning disk [email protected]...
Found 7 disks
ERROR: invalid device tree
Found EFI removable media binary efi/boot/bootaa64.efi
981992 bytes read in 44 ms (21.3 MiB/s)
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
WARNING could not find node vivante,gc: FDT_ERR_NOTFOUND.
Booting /efi\boot\bootaa64.efi
Cannot use 64 bit addresses with SDMA
Error reading cluster
** Unable to read file /efi/boot/grubaa64.efi **
Unexpected return from initial read: Device Error, buffersize 29D790
Failed to load image ￢ : Device Error
start_image() returned Device Error
EFI LOAD FAILED: continuing...
switch to partitions #0, OK
mmc1(part 0) is current device
Scanning mmc 1:1...
** Unable to read file / **
Failed to load '/'
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
BootOrder not defined
EFI boot manager: Cannot load any image
Scanning mmc 1:2...
** Unable to read file / **
Failed to load '/'
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
BootOrder not defined
EFI boot manager: Cannot load any image
starting USB...
Bus usb@3100000: Register 200017f NbrPorts 2
Starting the controller
USB XHCI 1.00
Bus usb@3110000: Register 200017f NbrPorts 2
Starting the controller
USB XHCI 1.00
scanning bus usb@3100000 for devices... 1 USB Device(s) found
scanning bus usb@3110000 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Device 0: unknown device
Trying load from SD ...
switch to partitions #0, OK
mmc0 is current device
Device: FSL_SDHC
Manufacturer ID: 9f
OEM: 5449
Name: SD32G
Bus Speed: 50000000
Mode: SD High Speed (50MHz)
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 28.9 GiB
Bus Width: 4-bit
Erase Group Size: 512 Bytes
MMC read: dev # 0, block # 32768, count 81920 ... 81920 blocks read: OK
Wrong Image Format for bootm command
ERROR: can't get kernel image!
Signed-off-by: Wei Ming Chen <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
|
|
Remove one of the double colon so ..code-block is used for formatting.
Signed-off-by: Leonard Anderweit <[email protected]>
Acked-by: Ilias Apalodimas <[email protected]>
Reviewed-by: Heinrich Schuchardt <[email protected]>
|
|
Document environment variables set by the dhcp command when the network
stack is lwIP.
Signed-off-by: Jerome Forissier <[email protected]>
|
|
Board introductions have a feature list which isn't formatted properly
according to rST and is thus rendered incorrectly.
Fix this by adding the missing newlines in the appropriate places.
Signed-off-by: Quentin Schulz <[email protected]>
|
|
Fix 'indicatged' and 'adress' typos.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Add a blank line after title "Specification:" to
make it render correctly html.
And also remove the useless > in bash code block.
Signed-off-by: Andy Yan <[email protected]>
Reviewed-by: Quentin Schulz <[email protected]>
|
|
Most Rockchip device tree related bindings are converted to YAML
and available in the U-boot /dts/upstream/Bindings/ directory.
Remove all redundant U-boot entries.
Signed-off-by: Johan Jonker <[email protected]>
|
|
Although it has historically been different, the current standard
spelling of the neutral singular possessive pronoun is "its".
Signed-off-by: J. Neuschäfer <[email protected]>
|
|
Cosmetic change.
Signed-off-by: J. Neuschäfer <[email protected]>
|
|
Since commit 61ff13283c3b ("board: sl28: move to OF_UPSTREAM") USB0 is
broken because the former u-boot soc dtsi was setting dr_mode to "host"
but the linux device tree isn't. That is because linux fully supports
OTG but u-boot doesn't. Therefore, u-boot only ever enabled host mode
and never OTG mode. Add it to our board "-u-boot.dtsi" to fix it.
Fixes: 61ff13283c3b ("board: sl28: move to OF_UPSTREAM")
Reported-by: Heiko Thiery <[email protected]>
Signed-off-by: Michael Walle <[email protected]>
Tested-by: Heiko Thiery <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
|
|
Convert the table to a correct reST table syntax.
Signed-off-by: Michael Walle <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
|
|
Network is broken on variant 3 boards since commit 61ff13283c3b ("board:
sl28: move to OF_UPSTREAM") because it was removing the variant 3
handling. That is because at that time the var3 device tree was not
upstream. FWIW variant 3 is actually the same as the base variant, but
I've missed that the -u-boot.dtsi is not inlcuded in this case which
will set the ethernet alias. Now that the var3 device tree is upstream,
just re-add it to the SPL handling again.
Fixes: 61ff13283c3b ("board: sl28: move to OF_UPSTREAM")
Signed-off-by: Michael Walle <[email protected]>
Reviewed-by: Heiko Thiery <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
|
|
Increase the malloc size to 2MiB because our FIT image exceeds the 1MiB
limit either if BL31 mode is enabled or if another device tree is added
to the image.
Signed-off-by: Michael Walle <[email protected]>
Tested-by: Heiko Thiery <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
|
|
We don't have a reference to the driver used by
uclass_get_device_by_driver() in stop_recovery_watchdog(). Fix it by not
calling that function if the watchdog driver isn't enabled.
Signed-off-by: Michael Walle <[email protected]>
Reviewed-by: Heiko Thiery <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
|
|
Anurag Dutta <[email protected]> says:
Hi All,
In u-boot, hbmc is broken and has been removed from j7200
configs. This series re-enables the hbmc driver and introduces a series
of hyperflash boot fixes. At present, in u-boot, the parent device (fss)
gets registered as a syscon device. This is done because the MMIO
mux driver in u-boot did not support the mux functionality when the
parent device is not a syscon. In this series, we make relevant changes
in the hbmc driver as well as dts' so that we can use the reg-mux driver for
selecting the appropriate state of the mux.
Test logs:
1) j721e-idk-gw hyperflash boot test: https://gist.github.com/anuragdutta731/50aae6fec707a3ffad6d985de6757fe4
2) j7200-evm hyperflash boot test: https://gist.github.com/anuragdutta731/c3a4d60f8bfd9c425d6c44b36eb7322b
Link: https://lore.kernel.org/r/[email protected]
|
|
The HBMC_AM654 driver was dependent on SYSCON because syscon APIs were
being used to select the multiplexer state. Change the dependency to
MULTIPLEXER and MUX_MMIO because mux APIs are now being used to
select mux state.
Signed-off-by: Anurag Dutta <[email protected]>
|
|
Kernel commit dbb124cf6888 ("configs: j7200: Remove HBMC_AM654
config") removed the HBMC_AM654 config because hbmc was broken
in u-boot. Hence, add the missing configs necessary to re-enable
Hyperflash boot.
Signed-off-by: Vaishnav Achath <[email protected]>
Signed-off-by: Anurag Dutta <[email protected]>
|
|
HyperFlash
The size of J7200 tiboot3.bin is 516KB but the memory reserved for it in
HyperFlash was 512KB. This led to overlap of tiboot3.bin over tispl.bin
region and break in HyperFlash boot mode.
Therefore, fix this by increasing the memory allocated for tiboot3.bin
to 1MB for J7200.
Fixes: cf1d6867f774 ("board: ti: j7200: Introduce support for j7200 build targets")
Signed-off-by: Aswath Govindraju <[email protected]>
Signed-off-by: Vaishnav Achath <[email protected]>
Signed-off-by: Anurag Dutta <[email protected]>
|
|
Kernel commit 5b2671594b80 ("configs: j721e: Remove HBMC_AM654
config") removed the HBMC_AM654 config because hbmc was broken
in u-boot. Hence, add the missing configs necessary to re-enable
Hyperflash boot.
Signed-off-by: Vaishnav Achath <[email protected]>
Signed-off-by: Anurag Dutta <[email protected]>
|
|
Add 32-bit address overrides for Hyper Bus Memory Controller
for Hyperflash to be functional in R5 SPL.
Signed-off-by: Vaishnav Achath <[email protected]>
Signed-off-by: Anurag Dutta <[email protected]>
|
|
Add 32-bit address overrides for Hyper Bus Memory Controller
for Hyperflash to be functional in R5 SPL.
Signed-off-by: Vaishnav Achath <[email protected]>
Signed-off-by: Anurag Dutta <[email protected]>
|
|
The syscon APIs were used for selecting the state of the mux
device because the mmio-mux driver in u-boot did not support
the mux functionality when the parent device is not a syscon.
Change to mux APIs which utilizes the reg-mux driver to select the
state of the multiplexer.
Signed-off-by: Anurag Dutta <[email protected]>
|
|
Add config required to build mmio-mux driver and dependencies.
Signed-off-by: Anurag Dutta <[email protected]>
|
|
Neha Malcom Francis <[email protected]> says:
Enable the NFS command across all platforms to allow network booting via
the NFS. Clean up the J7 configs to use TI_COMMON_CMD_OPTIONS.
Link: https://lore.kernel.org/r/[email protected]
|
|
Instead of bloating the defconfig with CONFIG_CMD_*, move J7 devices to
start using TI_COMMON_CMD_OPTIONS.
Signed-off-by: Neha Malcom Francis <[email protected]>
|
|
Add CMD_NFS to list of configs implied by CONFIG_TI_COMMON_CMD_OPTIONS.
This allows network booting via the NFS protocol from the U-Boot prompt.
Fixes: 10de12570799 ("disable NFS support by default")
Signed-off-by: Neha Malcom Francis <[email protected]>
|
|
Gokul Praveen <[email protected]> says:
The OMAP specific UART driver is changed from a generic implementation of
certain ops functions to an OMAP specific implementation of it to add
support for higher baudrates for OMAP devices.
Hence to support the above change, static functionality of ops functions
in generic ns16550 UART U-Boot driver is removed and also migrated certain
macros to its header file for usage in device-specific drivers.
Boot logs link :
https://gist.github.com/GOKU-THUG/8b90117c963e5da5c1b6caeee427c82c
Link: https://lore.kernel.org/r/[email protected]
|
|
higher baudrates
Move to OMAP specific implementation of certain ops functions as the UART
prints on the serial console fail for baudrates greater than 460800.
The MDR1 register is responsible for determining the speed mode at which
the UART should operate for OMAP specific devices. The baud divisor is used
to set the UART_DLL register which is used for generation of the baud
clock in the baud rate generator. The implementation logic is similar to
how it is implemented in omap_8250_get_divisor function of 8250_omap UART
linux driver.
Signed-off-by: Gokul Praveen <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Increase scope of ops functions and do some clean up for usage in device
-specific UART drivers.
Remove the static functionality of ops functions and migrate certain macros
to header file for usage in device-specific drivers.
Signed-off-by: Gokul Praveen <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Garrett Giordano <[email protected]> says:
This patch set adds the phyCORE AM62Ax board support and documenation to
u-boot.
The phyCORE-AM62Ax is a SoM (System on Module) featuring TI's AM62Ax SoC. It can
be used in combination with different carrier boards. This module can come
with different sizes and models for DDR, eMMC, SPI NOR Flash and various SoCs
from the AM62x family.
A development Kit, called phyBOARD-Lyra is used as a carrier board reference
design around the AM62x SoM.
This series depends on the following two patches:
- [PATCH v2] arm: mach-k3: am62a7: Provide a way to obtain boot device for non SPL
https://lists.denx.de/pipermail/u-boot/2024-October/570156.html
- [PATCH] board: phytec: common: Introduce CONFIG_PHYTEC_K3_DDR_PATCH
https://lists.denx.de/pipermail/u-boot/2024-November/571543.html
Link: https://lore.kernel.org/r/[email protected]
[trini: Fix warning in board/phytec/common/k3/board.c when
CONFIG_EFI_HAVE_CAPSULE_SUPPORT is not enabled]
Signed-off-by: Tom Rini <[email protected]>
|
|
Introduce get_boot_device() to obtain the booting device. Make it also
available for non SPL builds so u-boot can also know the device it
is booting from.
Signed-off-by: Garrett Giordano <[email protected]>
Reviewed-by: Bryan Brattlof <[email protected]>
Reviewed-by: Andrew Davis <[email protected]>
|
|
The module pid4 currently corresponds to the index of the toradex_module
array. If a new pid4 is introduced that does not follow the sequence of
the previous entries, it will create a gap in the array.
To address this, embed pid4 within the toradex_som structure and
implement a function to retrieve the index corresponding to pid4.
Signed-off-by: Vitor Soares <[email protected]>
Acked-by: Francesco Dolcini <[email protected]>
|
|
Add documentation for PHYTEC phyCORE-AM62ax SoM.
Signed-off-by: Garrett Giordano <[email protected]>
Reviewed-by: Wadim Egorov <[email protected]>
Reviewed-by: Dhruva Gole <[email protected]>
|
|
Add support for PHYTEC phyCORE-AM62A7 SoM.
Supported features:
- 2GB LPDDR4 RAM
- eMMC
- External SD
- Ethernet
- debug UART
Signed-off-by: Garrett Giordano <[email protected]>
Reviewed-by: Wadim Egorov <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Bryan Brattlof <[email protected]>
|
|
Wadim Egorov <[email protected]> says:
This implements capsule updates for all our K3 SoMs for
eMMC, OSPI NOR and uSD cards.
We can use capsule updates to update the bootloader on all our
supported flash devices.
Link: https://lore.kernel.org/r/[email protected]
|
|
Enable raw & on disk capsule updates and provide configs required
for updating MTD devices. Also resync after savedefconfig.
Signed-off-by: Wadim Egorov <[email protected]>
|
|
Implement EFI capsule update functionality for PHYTEC K3-based SoMs.
These SoMs feature various flash device options, including eMMC,
OSPI NOR, and uSD card at the board level.
This update provides the necessary logic to enable EFI capsule updates
across all three flash devices, ensuring flexible and robust firmware
upgrade capabilities.
The GUID is dynamically generated for the board, to get it:
efidebug capsule esrt
========================================
ESRT: fw_resource_count=3
ESRT: fw_resource_count_max=3
ESRT: fw_resource_version=1
[entry 0]==============================
ESRT: fw_class=C7D64D6D-10B2-54BC-A3BF-06A9DC3653D9
ESRT: fw_type=unknown
ESRT: fw_version=0
ESRT: lowest_supported_fw_version=0
ESRT: capsule_flags=0
ESRT: last_attempt_version=0
ESRT: last_attempt_status=success
[entry 1]==============================
ESRT: fw_class=09841C3F-F177-5D57-B1F6-754D92879205
ESRT: fw_type=unknown
ESRT: fw_version=0
ESRT: lowest_supported_fw_version=0
ESRT: capsule_flags=0
ESRT: last_attempt_version=0
ESRT: last_attempt_status=success
[entry 2]==============================
ESRT: fw_class=D11A9016-515E-503A-8872-3FF65384D0C4
ESRT: fw_type=unknown
ESRT: fw_version=0
ESRT: lowest_supported_fw_version=0
ESRT: capsule_flags=0
ESRT: last_attempt_version=0
ESRT: last_attempt_status=success
========================================
On the board (from uSD card containing capsule binaries at boot):
load mmc 1:1 $loadaddr tiboot3-capsule.bin
efidebug capsule update $loadaddr
load mmc 1:1 $loadaddr tispl-capsule.bin
efidebug capsule update $loadaddr
load mmc 1:1 $loadaddr uboot-capsule.bin
efidebug capsule update $loadaddr
The binaries will be flashed to the flash device you are booted from.
Signed-off-by: Wadim Egorov <[email protected]>
|
|
Fill in phycore-am64x capsule GUID properties of the base
binman capsule nodes.
Signed-off-by: Wadim Egorov <[email protected]>
|
|
Fill in phycore-am62x capsule GUID properties of the base
binman capsule nodes.
Signed-off-by: Wadim Egorov <[email protected]>
|
|
Siddharth Vadapalli <[email protected]> says:
Hello,
This series adds support for USB DFU boot on TI's AM62A SoC which has
two instances of DWC3 USB Controllers namely USB0 and USB1. The USB0
instance of the USB Controller supports USB DFU boot:
ROM => tiboot3.bin => tispl.bin => u-boot.img
USB DFU Boot requires the USB Controller to be configured for Gadget
mode of operation. Since the USB0 instance of the DWC3 USB Controller
supports both Host and Gadget modes of operation via the Type-C interface
on the AM62A7-SK board, the device-tree specifies the "dr_mode" as "OTG".
However, there is currently no support for dynamically switching the "mode"
from Host to Gadget and vice-versa with the help of a state-machine.
The OTG mode is treated as a separate mode in itself rather than being
treated as an intermediate stage before assuming the Host/Gadget mode.
Due to this, USB DFU boot via the Type-C interface doesn't work as the
USB Controller hasn't been appropriately configured for Device/Gadget
mode of operation. One option is to change the device-tree to specify
"dr_mode" as "peripheral" and force the controller to assume the Device
role. This will imply that the U-Boot device-tree for AM62A diverges
from its Linux counterpart. Therefore, with the intent of keeping the
device-tree uniform across Linux and U-Boot, and at the same time, in
order to enable USB DFU boot in "OTG" mode with the DWC3 Controller,
the first patch in this series sets the "mode" on the basis of the
caller function, rather than using the "dr_mode" property in the
device-tree. There are only two callers of "dwc3_generic_probe()",
each of which clearly specify the expected mode of configuration.
This will enable both Host and Device mode of operation based on the
command executed by the user, thereby truly supporting "OTG"
functionality when the USB Controller supports it.
The second patch in this series adds USB DFU environment for AM62A,
enabling USB DFU Boot and USB DFU flash on AM62A.
In addition to the patches in this series, the following device-tree
changes will be required to test USB DFU on AM62A (bootph-all property
to be added to ensure that USB Controller is present at all stages
for DFU Boot):
https://gist.github.com/Siddharth-Vadapalli-at-TI/53ba02cb0ff4a09c47e920d08247065f
The above device-tree changes will be made to the Linux device-tree,
which shall ensure that the same shall be a part of U-Boot device-tree
eventually.
The USB DFU config fragments for AM62x have been used for enabling
USB DFU boot on AM62a as follows:
R5 => am62ax_evm_r5_defconfig + am62x_r5_usbdfu.config
A53 => am62ax_evm_a53_defconfig + am62x_a53_usbdfu.config
Logs validating USB DFU boot with this series:
https://gist.github.com/Siddharth-Vadapalli-at-TI/daa71da1b0e478a51afea42605fb2d2c
Link: https://lore.kernel.org/r/[email protected]
|
|
Include the TI K3 DFU environment to support DFU Boot and DFU Flash.
Signed-off-by: Siddharth Vadapalli <[email protected]>
Reviewed-by: Roger Quadros <[email protected]>
|
|
There are only two callers of "dwc3_generic_probe()", namely:
1. dwc3_generic_peripheral_probe()
2. dwc3_generic_host_probe()
Currently, the "mode" is set based on the device-tree node of the
platform device. Also, the DWC3 core doesn't support updating the "mode"
dynamically at runtime if it is set to "OTG", i.e. "OTG" is treated as a
separate mode in itself, rather than being treated as a mode which should
eventually lead to "host"/"peripheral".
Given that the callers of "dwc3_generic_probe()" clarify the expected
"mode" of the USB Controller, use that "mode" instead of the one
specified in the device-tree. This shall allow the USB Controller to
function both as a "Host" and as a "Peripheral" when the "mode" is "otg"
in the device-tree, based on the caller of "dwc3_generic_probe()".
Signed-off-by: Siddharth Vadapalli <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
Reviewed-by: Roger Quadros <[email protected]>
|
|
Udit Kumar <[email protected]> says:
This enables the ESMs and the associated PMIC. Programming these bits is
a requirement to make the watchdog actually reset the board.
Logs
WDT reset J721S2
https://gist.github.com/uditkumarti/93cfe863d1f3fe3abb82b1821105f274#file-j721s2-L2708
AM68 boot (this does not support WDT)
https://gist.github.com/uditkumarti/93cfe863d1f3fe3abb82b1821105f274#file-am68
Link: https://lore.kernel.org/r/[email protected]
[trini: Merge configs/am68_sk_r5_defconfig]
Signed-off-by: Tom Rini <[email protected]>
|
|
Enables ESM configs for j721s2 and disables them for AM68 as AM68
includes J721s2 configs by default.
Signed-off-by: Manorit Chawdhry <[email protected]>
|
|
Add esm node for j721s2.
Signed-off-by: Manorit Chawdhry <[email protected]>
|
|
Initialize the 3 instances of SOC ESM & PMIC ESM.
This is needed for watchdog functionality.
Signed-off-by: Keerthy <[email protected]>
Signed-off-by: Udit Kumar <[email protected]>
|
|
Jayesh Choudhary <[email protected]> says:
Add QOS support for DSS in TI K3 SoC to route the DSS traffic through
RT queue by setting orderID as 15:
- J722S
- AM62P
Link: https://lore.kernel.org/r/[email protected]
|
