| Age | Commit message (Collapse) | Author |
|---|
|
This converts the following to Kconfig:
CONFIG_CMD_IRQ
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
At present IDE support is controlled by CONFIG_CMD_IDE. Add a separate
CONFIG_IDE option so that IDE support can be enabled without requiring
the 'ide' command.
Update existing users and move the ide driver into drivers/block since
it should not be in common/.
Signed-off-by: Simon Glass <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_CMD_ERRATA
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_CMD_EEPROM
CONFIG_CMD_EEPROM_LAYOUT
CONFIG_EEPROM_LAYOUT_HELP_STRING
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
[trini: Rework Kconfig logic slightly, define EEPROM location on TI eval
platforms]
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_CMD_ECCTEST
Signed-off-by: Simon Glass <[email protected]>
|
|
|
|
T1023 and T1024 have 4 SerDes lanes. Fix macro SRDS_MAX_LANES
and use this macro instead of hard-coded value in t1024_serdes.c.
Signed-off-by: Paulo Zaneti <[email protected]>
Signed-off-by: York Sun <[email protected]>
|
|
Drop use of this long-deprecated option for powerpc.
Signed-off-by: Simon Glass <[email protected]>
|
|
With 3f66149d9fb4 we no longer have a common call fdt_fixup_ethernet.
This was fine to do on PowerPC as they largely had calls already in
ft_cpu_fixup. On ARM however we largely relied on this call. Rather
than introduce a large number of changes to ft_cpu_fixup /
ft_board_fixup we recognize that this is a common enough call that we
should be doing it in a central location. Do it early enough that we
can do any further updates in ft_cpu_fixup / ft_board_fixup.
Cc: Gerd Hoffmann <[email protected]>
Cc: Chen-Yu Tsai <[email protected]>
Cc: Maxime Ripard <[email protected]>
Cc: Thomas Chou <[email protected]> (maintainer:NIOS)
Cc: York Sun <[email protected]> (maintainer:POWERPC MPC85XX)
Cc: Stefan Roese <[email protected]> (maintainer:POWERPC PPC4XX)
Cc: Simon Glass <[email protected]>
Cc: Joakim Tjernlund <[email protected]>
Fixes: 3f66149d9fb4 ("Remove extra fdt_fixup_ethernet() call")
Signed-off-by: Tom Rini <[email protected]>
Acked-by: Stefan Roese <[email protected]>
Acked-by: York Sun <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_CMD_DIAG
Signed-off-by: Simon Glass <[email protected]>
[trini: imply CMD_DIAG on some keymile configs]
Signed-off-by: Tom Rini <[email protected]>
|
|
Rather than using CMD_CRAMFS for both the filesystem and its command, we
should have a separate option for each. This allows us to enable CRAMFS
support without the command, if desired, which reduces U-Boot's size
slightly.
Signed-off-by: Simon Glass <[email protected]>
[trini: imply FS_CRAMFS for keymile]
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_CMD_CRAMFS
Signed-off-by: Simon Glass <[email protected]>
[trini: imply CMD_CRAMFS for keymile]
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_CMD_CHIP_CONFIG
Signed-off-by: Simon Glass <[email protected]>
|
|
For E6500 cores, L2 cache has been used as init_ram. L1 cache is a
write through cache on E6500.If lines are not locked in both L1 and
L2 caches, crashes are observed during secure boot. This patch locks/
unlocks both L1 and L2 cache to prevent the crash.
Signed-off-by: Ruchika Gupta <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
This allows us to use the same DRAM init function on all archs. Add a
dummy function for arc, which does not use DRAM init here.
Signed-off-by: Simon Glass <[email protected]>
[trini: Dummy function on nios2]
Signed-off-by: Tom Rini <[email protected]>
|
|
At present we cannot use this function as an init sequence call without a
wrapper, since it returns the RAM size. Adjust it to set the RAM size in
global_data instead, and return 0 on success.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
It looks like only cm5200 and tqm8xx use this feature, so we don't really
need it in generic code. Drop it and have the users access gd->board_type
directly.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Move these two function calls into checkcpu(), which is called on this
arch immediately after these two.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
This function is called just before checkcpu() on MPX83xx. Move it to the
code for that arch.
Signed-off-by: Simon Glass <[email protected]>
|
|
There is no good reason to use a different name on PowerPC. Change it to
timer_init() like the others.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: York Sun <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
We can just call this from the only place that needs it.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
We can just call this from the only function that needs it.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
We really don't need to have a name like this in the generic init
sequence. Use the generic get_clocks() name so that we can merge these
two at some point.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: York Sun <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Signed-off-by: Tom Rini <[email protected]>
Conflicts:
configs/ls1046aqds_defconfig
configs/ls1046aqds_nand_defconfig
configs/ls1046aqds_qspi_defconfig
configs/ls1046aqds_sdcard_ifc_defconfig
configs/ls1046aqds_sdcard_qspi_defconfig
configs/ls1046ardb_emmc_defconfig
configs/ls1046ardb_qspi_defconfig
configs/ls1046ardb_sdcard_defconfig
|
|
eLBC IP clock is always a constant divisor of platform clock
pre-defined per SoC. Clock ratio register (LCRR) used in
current implementation governs eLBC IP output cloc.
Update sys_info->freq_localbus to represent eLBC input clock with
value constant divisor of platform clock.
Signed-off-by: Prabhakar Kushwaha <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
Enable ELBC from Kconfig.
Signed-off-by: Prabhakar Kushwaha <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
IFC IP clock is always a constant divisor of platform clock
pre-defined per SoC. Clock control register (CCR) used in
current implementation governs IFC IP output clock.
Update sys_info->freq_localbus to represent IFC input clock with
value constant divisor of platform clock.
Signed-off-by: Prabhakar Kushwaha <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
Enable IFC from Kconfig.
Signed-off-by: Prabhakar Kushwaha <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
We should use the symbolic names for the cache control bits.
Signed-off-by: Mark Marshall <[email protected]>
Reviewed-by: Thomas Graziadei <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
To enable DM on MPC83xx, we need pre-relocation malloc, which is
implemented in this patch.
Signed-off-by: Mario Six <[email protected]>
[York S: Fixed compiling warning for unused variable 'i']
Reviewed-by: York Sun <[email protected]>
|
|
The r1 register is modified several times during the cache-ram setup of
the MPC83xx SoCs.
Since this SP modification confuses debuggers, we use a general purpose
register to compute the new stack pointer value, and only set the SP
once after all computations are done.
Signed-off-by: Mario Six <[email protected]>
Reviewed-by: Joakim Tjernlund <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
|
|
Rather than having an arch-specific function, use the existing generic
one.
Signed-off-by: Simon Glass <[email protected]>
|
|
This is not defined anywhere in U-Boot. Drop this dead code.
Signed-off-by: Simon Glass <[email protected]>
|
|
To avoid an unnecessary arch-specific call in board_init_f(), rename this
function.
Signed-off-by: Simon Glass <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_BOARD_EARLY_INIT_F
Signed-off-by: Simon Glass <[email protected]>
|
|
The read-only-write-enable bit is set by default and must be cleared
to prevent overwriting read-only registers. This should be done
immediately after resetting the PCI Express controller.
Reviewed-by: Hamish Martin <[email protected]>
Signed-off-by: Tony O'Brien <[email protected]>
[York S: Move SYS_FSL_ERRATUM_A007815 to Kconfig]
Reviewed-by: York Sun <[email protected]>
|
|
Core hang occurs when using L1 stashes. Workaround is to disable L1
stashes so software uses L2 cache for stashes instead.
Reviewed-by: Chris Packham <[email protected]>
Signed-off-by: Darwin Dingel <[email protected]>
Cc: York Sun <[email protected]>
[York S: Move SYS_FSL_ERRATUM_A007907 to Kconfig]
Reviewed-by: York Sun <[email protected]>
|
|
This option should not really be user selectable. Note that on PowerPC
we currently only need BOARD_LATE_INIT when CHAIN_OF_TRUST is enabled so be
conditional on that.
Signed-off-by: Tom Rini <[email protected]>
Acked-by: Masahiro Yamada <[email protected]> (for UniPhier)
|
|
Use Kconfig option SYS_PPC64 instead.
Signed-off-by: York Sun <[email protected]>
|
|
Use Kconfig option to select chassis version.
Signed-off-by: York Sun <[email protected]>
|
|
Use Kconfig option E6500 and clean up existing usage.
Signed-off-by: York Sun <[email protected]>
|
|
Use Kconfig to select DDR version instead of using config header.
Signed-off-by: York Sun <[email protected]>
|
|
These two macros are used for the same thing, the total number of DDR
controllers for a given SoC. Use SYS_NUM_DDR_CTRLS in Kconfig and
merge existing usage.
Signed-off-by: York Sun <[email protected]>
|
|
Use Kconfig to select errata workaround.
Signed-off-by: York Sun <[email protected]>
|
|
Add option SYS_FSL_ERRATUM_ESDHC111, SYS_FSL_ERRATUM_ESDHC13,
SYS_FSL_ERRATUM_ESDHC135, SYS_FSL_ERRATUM_ESDHC_A001 to mmc Kconfig.
Move existing macros to related Kconfig.
Signed-off-by: York Sun <[email protected]>
[trini: Migrate bk4r1]
Signed-off-by: Tom Rini <[email protected]>
|
|
Create driver/ddr/fsl/Kconfig and move existing options. Clean up
existing macros.
Signed-off-by: York Sun <[email protected]>
[trini: Migrate sbc8641d, xpedite537x and MPC8536DS, run a moveconfig.py -s]
Signed-off-by: Tom Rini <[email protected]>
|
|
Remove these SoCs from Kconfig because they don't have individual
configuration. Clean up existing macros.
Signed-off-by: York Sun <[email protected]>
|
|
Use Kconfig option to set little- or big-endian access to secure
boot and trust architecture.
Signed-off-by: York Sun <[email protected]>
|
|
Instead of define CONFIG_SYS_FSL_SEC_COMPAT in header files for PowerPC
and ARM SoCs, move it to Kconfig under the driver.
Signed-off-by: York Sun <[email protected]>
|
