| Age | Commit message (Collapse) | Author |
|---|
|
|
|
We are supposed to not add config entries with only "default y"
in board/SoC Kconfig files.
Signed-off-by: Masahiro Yamada <[email protected]>
Acked-by: Enric Balletbo i Serra <[email protected]>
|
|
Move this option to Kconfig and set its default value to 4; this
increases the number of supported CPUs for some boards.
It consumes 1KB memory per CPU for PSCI stack, but it should not
be a big deal, given the amount of memory used for the modern OSes.
Reviewed-by: Alexander Graf <[email protected]>
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Add ARCH_SUPPORT_PSCI as a non-configurable option that platforms
can select. Then, move CONFIG_ARMV7_PSCI, which is automatically
enabled if both ARMV7_NONSEC and ARCH_SUPPORT_PSCI are enabled.
Reviewed-by: Alexander Graf <[email protected]>
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
If CONFIG_ARMV7_NONSEC is enabled, the linker script requires
CONFIG_ARMV7_PSCI_NR_CPUS regardless of CONFIG_ARMV7_PSCI.
Reviewed-by: Alexander Graf <[email protected]>
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
SPL_BUILD is not a CONFIG in Kconfig, so !SPL_BUILD is always true.
Reviewed-by: Alexander Graf <[email protected]>
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
On all TI platforms the ROM defines a "downloaded image" area at or near
the start of SRAM which is followed by a reserved area. As it is at
best bad form and at worst possibly harmful in corner cases to write in
this reserved area, we stop doing that by adding in the define
NON_SECURE_SRAM_IMG_END to say where the end of the downloaded image
area is and make SRAM_SCRATCH_SPACE_ADDR be one kilobyte before this.
At current we define the end of scratch space at 0x228 bytes past the
start of scratch space this this gives us a lot of room to grow. As
these scratch uses are non-optional today, all targets are modified to
respect this boundary.
Tested on OMAP4 Pandaboard, OMAP3 Beagle xM
Cc: Albert Aribaud <[email protected]>
Cc: Nagendra T S <[email protected]>
Cc: Vaibhav Hiremath <[email protected]>
Cc: Lokesh Vutla <[email protected]>
Cc: Felipe Balbi <[email protected]>
Cc: Igor Grinberg <[email protected]>
Cc: Nikita Kiryanov <[email protected]>
Cc: Paul Kocialkowski <[email protected]>
Cc: Enric Balletbo i Serra <[email protected]>
Cc: Adam Ford <[email protected]>
Cc: Steve Sakoman <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: Thomas Weber <[email protected]>
Cc: Hannes Schmelzer <[email protected]>
Cc: Thomas Chou <[email protected]>
Cc: Masahiro Yamada <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Joe Hershberger <[email protected]>
Cc: Sam Protsenko <[email protected]>
Cc: Heiko Schocher <[email protected]>
Cc: Samuel Egli <[email protected]>
Cc: Michal Simek <[email protected]>
Cc: Wolfgang Denk <[email protected]>
Cc: Mateusz Kulikowski <[email protected]>
Cc: Ben Whitten <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Bin Meng <[email protected]>
Cc: Sekhar Nori <[email protected]>
Cc: Mugunthan V N <[email protected]>
Cc: "B, Ravi" <[email protected]>
Cc: "Matwey V. Kornilov" <[email protected]>
Cc: Ladislav Michl <[email protected]>
Cc: Ash Charles <[email protected]>
Cc: "Kipisz, Steven" <[email protected]>
Cc: Daniel Allred <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Tested-by: Lokesh Vutla <[email protected]>
Acked-by: Lokesh Vutla <[email protected]>
Tested-by: Ladislav Michl <[email protected]>
|
|
Remove the device definition from board file, update the driver with
the new compatible property and update config with necessary options.
Signed-off-by: Beniamino Galvani <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Import DTS files and dt-bindings includes from Linux 4.8-rc1.
Signed-off-by: Beniamino Galvani <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
So far we could only tell the gpio framework that a GPIO was mapped as input or
output, not as alternative function.
This patch adds support for determining whether a function is mapped as
alternative.
Signed-off-by: Alexander Graf <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Acked-by: Stephen Warren <[email protected]>
|
|
Currently MX6 SPL DDR initialization hardcodes the REF_SEL and
REFR fields of the MDREF register as 1 and 7, respectively for
DDR3 and 0 and 3 for LPDDR2.
Looking at the MDREF initialization done via DCD we see that
boards do need to initialize these fields differently:
$ git grep 0x021b0020 board/
board/bachmann/ot1200/mx6q_4x_mt41j128.cfg:DATA 4 0x021b0020 0x00005800
board/ccv/xpress/imximage.cfg:DATA 4 0x021b0020 0x00000800 /* MMDC0_MDREF */
board/freescale/mx6qarm2/imximage.cfg:DATA 4 0x021b0020 0x7800
board/freescale/mx6qarm2/imximage.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qarm2/imximage_mx6dl.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qarm2/imximage_mx6dl.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qsabreauto/imximage.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qsabreauto/mx6dl.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qsabreauto/mx6qp.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6sabresd/mx6dlsabresd.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6sabresd/mx6q_4x_mt41j128.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6slevk/imximage.cfg:DATA 4 0x021b0020 0x00001800
board/freescale/mx6sxsabreauto/imximage.cfg:DATA 4 0x021b0020 0x00000800
board/freescale/mx6sxsabresd/imximage.cfg:DATA 4 0x021b0020 0x00000800
board/warp/imximage.cfg:DATA 4 0x021b0020 0x00001800
So introduce a mechanism for users to be able to configure
REFSEL and REFR fields as needed.
Keep all the mx6 SPL users in their current REF_SEL and REFR values,
so no functional changes for the existing users.
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Eric Nelson <[email protected]>
|
|
Add support for Advantech DMS-BA16 board. The board is based on Advantech
BA16 module which has a i.MX6D processor. The board supports:
- FEC Ethernet
- USB Ports
- SDHC and MMC boot
- SPI NOR
- LVDS and HDMI display
Basic information about the module:
- Module manufacturer: Advantech
- CPU: Freescale ARM Cortex-A9 i.MX6D
- SPECS:
Up to 2GB Onboard DDR3 Memory;
Up to 16GB Onboard eMMC NAND Flash
Supports OpenGL ES 2.0 and OpenVG 1.1
HDMI, 24-bit LVDS
1x UART, 2x I2C, 8x GPIO,
4x Host USB 2.0 port, 1x USB OTG port,
1x micro SD (SDHC),1x SDIO, 1x SATA II,
1x 10/100/1000 Mbps Ethernet, 1x PCIe X1 Gen2
Signed-off-by: Akshay Bhat <[email protected]>
Cc: [email protected]
Cc: [email protected]
|
|
|
|
With commit ceec08f50b6, phy is connected to slave 0, but
changing the phy node was missed, fix it by populating the
phy node to proper cpsw slave node.
Fixes: ceec08f50b6 ("ARM: dts: dra72-evm: Add mode-gpios entry for mac node")
Signed-off-by: Mugunthan V N <[email protected]>
Cc: Vignesh R <[email protected]>
Tested-by: Tom Rini <[email protected]>
|
|
The Orange Pi Plus2E is an extended version of the Orange Pi Pc Plus,
with 2G RAM and an external gbit ethernet phy.
The dts file is identical to the one submitted to the upstream kernel,
except that it has the pending patch to enable the ethernet controller
squashed in, as u-boot already has sun8i-emac support.
Signed-off-by: Hans de Goede <[email protected]>
|
|
This adds an emac node to the orangepi-2 dts (not yet merged upstream,
but in u-boot we already have emac support); fixes the alphetically
sorting of nodes in sun8i-h3-orangepi-plus.dts and disables some
usb controllers in sun8i-h3-orangepi-plus.dts which are only used
on the plus2e, as upstream has decided to do a separate dts files
for the plus2e.
Signed-off-by: Hans de Goede <[email protected]>
|
|
The sun8i-emac driver follows an old version of the proposed DT
bindings, where the EMAC clock and EPHY control register range is
listed directly, rather than through a syscon phandle.
Add back the syscon register range to avoid an invalid data access.
We should fix the driver once the Linux kernel bindings have been
finalized.
Signed-off-by: Chen-Yu Tsai <[email protected]>
Reviewed-by: Hans de Goede <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|
|
A33-OLinuXino is A33 development board designed by Olimex LTD.
It has AXP223 PMU, 1GB DRAM, a micro SD card, one USB-OTG connector,
headphone and mic jacks, connector for LiPo battery and optional
4GB NAND Flash.
It has two 40-pin headers. One for LCD panel, and one for
additional modules. Also there is CSI/DSI connector.
The dts files are identical to the ones submitted to the upstream kernel.
Signed-off-by: Stefan Mavrodiev <[email protected]>
Reviewed-by: Hans de Goede <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|
|
Add a proper dts for the iNet D978 rev2 based A33 tablets.
Signed-off-by: Icenowy Zheng <[email protected]>
Acked-by: Hans de Goede <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|
|
The Colorado TK1 SOM is a small form factor board similar to the
Jetson TK1. The main differences lie in the pinmux, and in that the
PCIe controller is set to use in 4lanes+1lane, rather than 2+2.
The pinmux header here was generated from a spreadsheet provided by
Colorado Engineering using the tegra-pinmux scripts. The spreadsheet
was converted from v09 to v11 by me.
Signed-off-by: Peter Chubb <[email protected]>
Acked-by: Stephen Warren <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
The board ID EEPROM and board ID stickers on p2771-0000 will use a numeric
versioning scheme, with version numbers such as 000/100/200/300/400/500.
Within NVIDIA, these versions are also known as A00/A01/A02/A03/A04/B00.
However, that numbering scheme is not easily visible outside of NVIDIA,
and so does not make much sense to use. Convert U-Boot to use the readily
visible numeric scheme.
Also, it turns out that the current A02 DT actually applies to board
versions 000/100/200 (A00..A02). Consequently rename this to 000 not 200
so that all U-Boot builds are named after the first version of the HW they
support.
Signed-off-by: Stephen Warren <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
There are lots of warnings when building EFI 64-bit payload.
include/asm-generic/bitops/__fls.h:17:2:
warning: left shift count >= width of type
if (!(word & (~0ul << 32))) {
^
In fact, U-Boot itself as EFI payload is running in 32-bit mode.
So BITS_PER_LONG needs to still be 32, but EFI status codes are
64-bit when booting from 64-bit EFI. Introduce EFI_BITS_PER_LONG
to bridge those status codes with U-Boot's BITS_PER_LONG.
Signed-off-by: Bin Meng <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add a debug() at this point to help figure out what is wrong.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
Generally the microcode is combined into a single block only (and removed
from the device tree) when there are multiple blocks. But this is not a
requirement.
Adjust the ivybridge code to avoid assuming this.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
Add a debug() at this point to help figure out what is wrong.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Heiko Schocher<[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
|
|
The eMMC on sLD3 is assigned with dedicated pins (only multiplexed
with GPIO), so it shouldn't hurt to enable eMMC on SPL all the time.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
The revision of the original support card (rev 3.5, rev 3.6) fits in
the 8 bit width revision register. When it was extended in a weird
way, it was versioned in the format of "3.6.x" (where it should have
been "3.7", of course). What is worse, only the sub-level version
"6.x" was recorded in the 8 bit width register, completely ignoring
the compatibility of the revision register format.
This patch saves madly-versioned support cards by assuming the major
version "3" when the MSB 4 bit of the register is read as "6". With
this, the support card revision that were displayed as "6.10" is now
corrected to "3.6.10".
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
This supports the system reset via PSCI for ARMv7 SoCs.
Because the system reset is not supported on PSCI 0.1, let's define
CONFIG_ARMV7_PSCI_1_0. (it is supported since PSCI 0.2, but there
is no CONFIG to enable it in U-Boot for now.)
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
|
|
Most of them are my mistakes.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
The page table is maintained by the CPU, hence it is safe to always
align cache flush to a whole cache line size. This allows to use
mmu_page_table_flush for a single page table, e.g. when configure
only small regions through mmu_set_region_dcache_behaviour.
Signed-off-by: Stefan Agner <[email protected]>
Tested-by: Fabio Estevam <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
|
|
Add LPAE support for mmu_set_region_dcache_behaviour. The function
is in use in some LPAE capable board such TI DRA7xx or NXP i.MX 7.
Signed-off-by: Stefan Agner <[email protected]>
|
|
Use a tab not 8 spaces.
Signed-off-by: Tom Rini <[email protected]>
|
|
This series moves the CONFIG_SYS_CACHELINE_SIZE. First, in nearly all
cases we are mirroring the values used by the Linux Kernel here. Also,
so long as (and in this case, it is true) we implement flushes in hunks
that are no larger than the smallest implementation (and given that we
mirror the Linux Kernel, again we are fine) it is OK to align higher.
The biggest changes here are that we always use 64 bytes for CPU_V7 even
if for example the underlying core is only 32 bytes (this mirrors
Linux). Second, we say ARM64 uses 64 bytes not 128 (as found in the
Linux Kernel) as we do not need multi-platform support (to this degree)
and only the Cavium ThunderX 88xx series has a use for such large
alignment.
Cc: Albert Aribaud <[email protected]>
Cc: Marek Vasut <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Prafulla Wadaskar <[email protected]>
Cc: Luka Perkov <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: Nagendra T S <[email protected]>
Cc: Vaibhav Hiremath <[email protected]>
Acked-by: Lokesh Vutla <[email protected]>
Cc: Steve Rae <[email protected]>
Cc: Igor Grinberg <[email protected]>
Cc: Nikita Kiryanov <[email protected]>
Cc: Stefan Agner <[email protected]>
Acked-by: Heiko Schocher <[email protected]>
Cc: Mateusz Kulikowski <[email protected]>
Cc: Peter Griffin <[email protected]>
Acked-by: Paul Kocialkowski <[email protected]>
Cc: Anatolij Gustschin <[email protected]>
Acked-by: "Pali Rohár" <[email protected]>
Cc: Adam Ford <[email protected]>
Cc: Steve Sakoman <[email protected]>
Cc: Grazvydas Ignotas <[email protected]>
Cc: Nishanth Menon <[email protected]>
Cc: Stephen Warren <[email protected]>
Cc: Robert Baldyga <[email protected]>
Cc: Minkyu Kang <[email protected]>
Cc: Thomas Weber <[email protected]>
Cc: Masahiro Yamada <[email protected]>
Cc: David Feng <[email protected]>
Cc: Alison Wang <[email protected]>
Cc: Michal Simek <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: York Sun <[email protected]>
Cc: Shengzhou Liu <[email protected]>
Cc: Mingkai Hu <[email protected]>
Cc: Prabhakar Kushwaha <[email protected]>
Cc: Aneesh Bansal <[email protected]>
Cc: Saksham Jain <[email protected]>
Cc: Qianyu Gong <[email protected]>
Cc: Wang Dongsheng <[email protected]>
Cc: Alex Porosanu <[email protected]>
Cc: Hongbo Zhang <[email protected]>
Cc: tang yuantian <[email protected]>
Cc: Rajesh Bhagat <[email protected]>
Cc: Josh Wu <[email protected]>
Cc: Bo Shen <[email protected]>
Cc: Viresh Kumar <[email protected]>
Cc: Hannes Schmelzer <[email protected]>
Cc: Thomas Chou <[email protected]>
Cc: Joe Hershberger <[email protected]>
Cc: Sam Protsenko <[email protected]>
Cc: Bin Meng <[email protected]>
Cc: Christophe Ricard <[email protected]>
Cc: Anand Moon <[email protected]>
Cc: Beniamino Galvani <[email protected]>
Cc: Carlo Caione <[email protected]>
Cc: huang lin <[email protected]>
Cc: Sjoerd Simons <[email protected]>
Cc: Xu Ziyuan <[email protected]>
Cc: "[email protected]" <[email protected]>
Cc: "Ariel D'Alessandro" <[email protected]>
Cc: Kever Yang <[email protected]>
Cc: Samuel Egli <[email protected]>
Cc: Chin Liang See <[email protected]>
Cc: Dinh Nguyen <[email protected]>
Cc: Hans de Goede <[email protected]>
Cc: Ian Campbell <[email protected]>
Cc: Siarhei Siamashka <[email protected]>
Cc: Boris Brezillon <[email protected]>
Cc: Andre Przywara <[email protected]>
Cc: Bernhard Nortmann <[email protected]>
Cc: Wolfgang Denk <[email protected]>
Cc: Ben Whitten <[email protected]>
Cc: Tom Warren <[email protected]>
Cc: Alexander Graf <[email protected]>
Cc: Sekhar Nori <[email protected]>
Cc: Vitaly Andrianov <[email protected]>
Cc: "Andrew F. Davis" <[email protected]>
Cc: Murali Karicheri <[email protected]>
Cc: Carlos Hernandez <[email protected]>
Cc: Ladislav Michl <[email protected]>
Cc: Ash Charles <[email protected]>
Cc: Mugunthan V N <[email protected]>
Cc: Daniel Allred <[email protected]>
Cc: Gong Qianyu <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Acked-by: Masahiro Yamada <[email protected]>
Acked-by: Chin Liang See <[email protected]>
Tested-by: Stephen Warren <[email protected]>
Acked-by: Paul Kocialkowski <[email protected]>
|
|
The H3 PLL5 used for DRAM barely manages to lock to the required
frequency before DRAM controller starts, sometimes leading to wrong
delay-line calibration results.
This patch changes the PLL tuning parameters to the same values as
boot0 used, which speeds up the locking and fixes the problem.
Signed-off-by: Jens Kuske <[email protected]>
Reviewed-by: Hans de Goede <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|
|
When the backlight's pwm input is connected to a pwm output of the SoC,
actually use pwm to drive the backlight.
The mean reason for doing this is to fix the backlight turning off
for aprox. 1 second while the kernel is booting. This is caused by
the kernel actually using pwm to drive the backlight, so that it
can dim the backlight. First the pwm driver loads and switches the
pinmux for the pin driving the backlight's pwm input to the pwm
controller. Then about 1s later the actual backlight driver loads
and tells the pwm driver to actually update the pwm settings, which
have a power-on-reset value of "off".
An additional advantage is that this allows us to initatiate the
backlight at 80%, which is the kernel default, avoiding a brightness
change while the kernel loads.
Signed-off-by: Hans de Goede <[email protected]>
Reviewed by: Peter Korsgaard <[email protected]>
|
|
Add a defconfig and dts file for the Empire Electronix M712 tablet, this
is a 7" A13 tablet, with micro-usb (otg), headphone and micro-sd slots on
the outside. It uses a Goodix gt811 touchscreen controller, a RTL8188CTV
wifi chip and a DMART06 (1238a4) accelerometer.
The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <[email protected]>
|
|
Sync dts files with the current (Aug 18th 2016) state of Maxime's
linux/sunxi/for-next repo.
Note this commit also updates configs/MSI_Primo81_defconfig,
adding: "# CONFIG_REQUIRE_SERIAL_CONSOLE is not set", this is necessary
because the tablet does not have a reachable uart so the dts sync
drops its serial0 alias.
Signed-off-by: Hans de Goede <[email protected]>
Acked-by: Ian Campbell <[email protected]>
|
|
Add a defconfig and dts file for tablets using the generic inet-q972 PCB.
Tablets with this PCB feature a mini-hdmi output, micro-usb usb-host,
micro-usb usb-otg, 3.5mm headphone jack, a micro sd slot,
(mini) power-barrel and an usb wifi module.
This has been tested on a 9.7" 1024x768 qware qw tb9718-qhd tablet.
The dts files are identical to the ones submitted to the upstream kernel.
Signed-off-by: Hans de Goede <[email protected]>
Acked-by: Ian Campbell <[email protected]>
|
|
|
|
Signed-off-by: Chris Packham <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Ensure appropriate error messages are generated. Previously all errors
indicated that the serdes was already in use. Now appropriate error
messages are given.
Signed-off-by: Chris Packham <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
The NAND interface on the Armada-38x series is similar to that on the
Armada-XP. The key difference is that the NAND ECC clock ratio is
provided via the DFX Server registers instead of the Core Clock.
Signed-off-by: Chris Packham <[email protected]>
Cc: Luka Perkov <[email protected]>
Cc: Dirk Eibach <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
The nvidia,bpmp property is left over from an old BPMP I2C binding, and
shouldn't be present. Remove it from the SoC DT file, and update the
I2C driver not to parse it; the value wasn't used for anything any more
anyway.
Signed-off-by: Stephen Warren <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
The Tegra SDHCI binding dictates that the reseet name for the Tegra SDHCI
clock be "sdhci" not "sdmmc", and that the clock is accessed by index
rather than by name. Fix the Tegra186 DT and MMC driver to honor this.
Signed-off-by: Stephen Warren <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
The Tegra I2C binding dictates that the clock name for the Tegra I2C clock
be "div-clk" not "i2c". Fix the Tegra186 DT and I2C driver to honor this.
Signed-off-by: Stephen Warren <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
[trini: Drop CMD_BOOTI as it's now on by default on ARM64]
Signed-off-by: Tom Rini <[email protected]>
|
|
There is no reason to duplicate code for DRA7xx platforms as there
can be Rail grouping. The maximum voltage detection algorithm can still
be run on other platforms with no Rail grouping and does not harm as
it gives the same result.
Signed-off-by: Lokesh Vutla <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
gpio_en field is introduced to detect if pmic is controlled by GPIO.
Make this field 0 on all TPS659* pmics available on DRA7/OMAP5 based platforms
and remove the #ifndefs.
Reviewed-by: Keerthy <[email protected]>
Signed-off-by: Lokesh Vutla <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
