| Age | Commit message (Collapse) | Author |
|---|
|
This particular chunk of code was not updated, likely due to the order
in which the patches were posted and applied. Fix this missing part.
Fixes: bb25aca13433 ("arm: socfpga: Convert reset manager from struct to defines")
Signed-off-by: Marek Vasut <[email protected]>
Cc: Chin Liang See <[email protected]>
Cc: Dalon Westergreen <[email protected]>
Cc: Dinh Nguyen <[email protected]>
Cc: Ley Foon Tan <[email protected]>
Cc: Simon Goldschmidt <[email protected]>
Cc: Tien Fong Chee <[email protected]>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip
- Support redundant boot for rk3399
- Support binman for rockchip platform
- Update ram driver and add ddr4 support for rk3328
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-uniphier
UniPhier SoC updates for v2020.04 (2nd)
Denali NAND driver changes:
- Set up more registers in denali-spl for SOCFPGA
- Make clocks optional
- Do not assert reset signals in the remove hook
- associate SPARE_AREA_SKIP_BYTES with DT compatible
- switch to UCLASS_MTD
UniPhier platform changes:
- fix a bug in dram_init()
- specify loadaddr for "source" command
|
|
gd->ram_base is not set at all if the end address of the DRAM ch0
exceeds the 4GB limit.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
UCLASS_MTD is a better fit for NAND drivers.
Make NAND_DENALI_DT depend on DM_MTD, which is needed to compile
drivers/mtd/mtd-uclass.c
Also, make ARCH_UNIPHIER select DM_MTD because all the defconfig
of this platform enables NAND_DENALI_DT.
Signed-off-by: Masahiro Yamada <[email protected]>
Reviewed-by: Miquel Raynal <[email protected]>
|
|
Now that the reset controlling of the Denali NAND driver (denali_dt.c)
works for this platform, remove the adhoc reset deassert code.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Add alias for mmc/sdmmc so that we can have a fix mmc number for emmc.
Signed-off-by: Kever Yang <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
update lpddr3 setting for fix init fail about "col error".
Signed-off-by: YouMin Chen <[email protected]>
Signed-off-by: Kever Yang <[email protected]>
|
|
Add rk3328-sdram-ddr4-666.dtsi for support ddr4 init.
Signed-off-by: YouMin Chen <[email protected]>
Signed-off-by: Kever Yang <[email protected]>
|
|
All rockchip platforms support TPL or SPL-based bootloader
in mainline with U-Boot proper as final stage. For each
stage we need to burn the image on to flash with respective
offsets.
This patch creates a single boot image component using
- binman, for arm32 rockchip platforms
- pad_cat, for arm64 rockchip platforms.
This would help users to get rid of burning different
boot stage images.
The new image called 'u-boot-rockchip.bin'
which can burn into flash like:
₹ sudo dd if=u-boot-rockchip.bin of=/dev/sda seek=64
This would support all rockchip platforms, except rk3128
since it doesn't support for SPL yet.
Cc: Matwey V. Kornilov <[email protected]>
Cc: Wadim Egorov <[email protected]>
Signed-off-by: Jagan Teki <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
Add U-Boot specific dtsi file for rk3188 SoC. This
would help to add U-Boot specific dts nodes, properties
which are common across rk3188.
Right now, the file is empty, will add required changes
in future patches.
Signed-off-by: Jagan Teki <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
Add U-Boot specific dtsi file for rk3036 SoC. This
would help to add U-Boot specific dts nodes, properties
which are common across rk3036.
Right now, the file is empty, will add required changes
in future patches.
Signed-off-by: Jagan Teki <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
Add bootcount support for Rockchip rk3399.
The bootcount value is preserved in PMU_SYS_REG0 register,
this would help to support redundent boot.
Once the redundant boot triggers, the altboot command
will look for extlinux-rollback.conf on particular
bootable partition which supposed to be a recovery
partition where redundant boot required.
Reviewed-by: Kever Yang <[email protected]>
Signed-off-by: Jagan Teki <[email protected]>
|
|
Add cpu reset cause in common cpu-info file.
This would help to print the reset cause for
various resets.
Right now it support rk3288, rk3399. rest of rockchip
platforms doesn't have reset cause support ye but this
code is more feasible to extend the same.
Reviewed-by: Kever Yang <[email protected]>
Signed-off-by: Jagan Teki <[email protected]>
|
|
Few of the rockchip family SoC atleast rk3288,
rk3399 are sharing some cru register bits so
adding common code between these SoC families
would require to include both cru include files
that indeed resulting function declarations error.
So, create a common cru include as cru.h then
include the rk3399 arch cru include file and move
the common cru register bit definitions into it.
The rest of rockchip cru files will add it in future.
Reviewed-by: Kever Yang <[email protected]>
Signed-off-by: Jagan Teki <[email protected]>
|
|
Add cpu information for rockchip soc.
This would help to print the SoC family number, with
associated temparature, clock and reason for reset etc.
Reviewed-by: Kever Yang <[email protected]>
Signed-off-by: Jagan Teki <[email protected]>
|
|
Enable winbond SPI flash for ROC-PC-RK3399 board.
Signed-off-by: Jagan Teki <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
Enable winbond SPI flash for ROC-PC-RK3399 board.
Signed-off-by: Jagan Teki <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
Sync the ROC-RK3399-PC device tree changes from Linux
with below commit details:
commit <c36308abe4110e4db362d5e2ae3797834a7b1192> ("arm64: dts:
rockchip: Enable MTD Flash on rk3399-roc-pc")
Signed-off-by: Jagan Teki <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
Some of the devices(for instance, pcie and gnet controller) sitting on
SCB bus falls behind/below the memory range that we currenty have.
This patch updates the memory range to map those devices correctly.
Signed-off-by: Amit Singh Tomar <[email protected]>
Reviewed-by: Andre Przywara <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
Tested-by: Corentin Labbe <[email protected]>
Signed-off-by: Matthias Brugger <[email protected]>
|
|
- Various exynos fixes
|
|
XOM pins provide information for iROM bootloader about the boot device.
Those pins are mapped to lower bits of OP_MODE register (0x10000008),
which is common for all Exynos SoC variants. Set the default MMC device id
to reflect the boot device selected by XOM[7:5] pins (2 for the SD or 0 for
the eMMC).
Signed-off-by: Marek Szyprowski <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-clk
- Various clock fixes and enhancements
|
|
Since frac_pll_init() is only used in this file, change it to 'static'.
This fixes the following sparse warning:
arch/arm/mach-imx/imx8m/clock_imx8mq.c:662:5: warning: no previous
prototype for ‘frac_pll_init’ [-Wmissing-prototypes]
Signed-off-by: Pedro Jardim <[email protected]>
|
|
Function sscg_pll_init() is not used anywhere, so it can simply be deleted.
This was found because of the following sparse
warning:
arch/arm/mach-imx/imx8m/clock_imx8mq.c:702:5: warning: no previous prototype for ‘sscg_pll_init’ [-Wmissing-prototypes]
int sscg_pll_init(u32 pll)
^~~~~~~~~~~~~
Signed-off-by: Pedro Jardim <[email protected]>
|
|
Since do_imx8m_showclocks() is only used inside this file, make it 'static'.
This fixes the following sparse warning:
arch/arm/mach-imx/imx8m/clock_imx8mq.c:836:5: warning: no previous prototype
for ‘do_imx8m_showclocks’ [-Wmissing-prototypes]
int do_imx8m_showclocks(cmd_tbl_t *cmdtp, int flag, int argc,
^~~~~~~~~~~~~~~~~~~
Signed-off-by: Pedro Jardim <[email protected]>
|
|
Function init_usb_clk() is not used anywhere, so it can simply be deleted.
This was detected by the following sparse warning:
arch/arm/mach-imx/imx8m/clock_imx8mq.c:377:6: warning: no previous prototype
for ‘init_usb_clk’ [-Wmissing-prototypes]
void init_usb_clk(void)
^~~~~~~~~~~~
Signed-off-by: Pedro Jardim <[email protected]>
|
|
- Libre Computer ALL-H3-IT/ALL-H5-CC board (Chen-Yu Tsai)
- Allwinner R40 Ethernet, usb phy enablement (Andre Przywara)
- Sunxi auto load from 128KB MMC offset (Andre Przywara)
- Orange Pi Win Ethernet phy enablement (Jernej Skrabec)
|
|
Since commit 067e0b9684d4 ("sunxi: Allow booting from 128KB SD/eMMC offset")
we support having the SPL loaded from either the traditional 8KB SD
card/eMMC offset, or from the alternative location at 128KB. However the
sector to find the U-Boot image was still hard-coded at compile time,
and had to be adjusted for one of the two choices.
Since we can actually override the function to return the sector offset,
we can just check the boot source byte there to select the proper offset
based on from where the SPL was loaded.
This allows the very same binary image to be loaded from either 128KB or
8KB, with the U-Boot proper image always being located just behind the SPL.
Signed-off-by: Andre Przywara <[email protected]>
Acked-by: Jagan Teki <[email protected]>
|
|
The Boot ROM write some boot source ID (SD card, eMMC, SPI, ...) into
a certain location in SRAM, so the SPL can easily determine where to
load U-Boot proper from.
Factor out reading this value, as it will come in handy again shortly.
Signed-off-by: Andre Przywara <[email protected]>
Acked-by: Jagan Teki <[email protected]>
|
|
Updates and fixes for ls1028a, lx2160a, ls1012a, ls1021a, ls2080a,
ls1088a platforms:
- lx2-rev2 pcie support, enetc related updates, layerscape-pcie fixes
|
|
Subsystems such as USB expect dma_map_single() and dma_unmap_single() to
do dcache flush/invalidate operations as required. For example, see
see drivers/usb/gadget/udc/udc-core.c::usb_gadget_map_request().
Currently drivers do this locally, (see drivers/usb/dwc3/ep0.c,
drivers/mtd/nand/raw/denali.c etc..)
Update arch specific dma_map_single() and dma_unmap_single() APIs to do
cache flush/invalidate operations, so that drivers need not implement
them locally.
Signed-off-by: Vignesh Raghavendra <[email protected]>
Reviewed-by: Masahiro Yamada <[email protected]>
Reviewed-by: Rick Chen <[email protected]>
|
|
Using musb-new structure for mt85xx gadget driver.
Add gadget driver dts for mt8518 SoCs.
Signed-off-by: mingming lee <[email protected]>
|
|
Since every Allwinner USB PHY seems to be slightly different from each
other, we need to add the compatible string and the respective data
structure to make it work on the R40/V40 SoC.
Nothing spectacular this time, just one less USB controller than the H3.
Copied from the Linux kernel.
Signed-off-by: Andre Przywara <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
Update the .dts file from the kernel, which carries much more nodes,
some of them we need to enable USB and Ethernet support for the board.
Signed-off-by: Andre Przywara <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
Sync the device tree files and device tree header files from upstream
Linux kernel, as of 2020-01-08. The commit synced to in the sunxi repo
98d25b0b266d Merge branch 'sunxi/dt-for-5.6' into sunxi/for-next
which is also part of next-20200108.
Changes brought in include:
- cleanup of pinmux node names
- addition of Security ID, MBUS, CSI, crypto engine, video codec,
pmu, and thermal sensor device nodes for both SoCs
- addition of deinterlacing engine device node on H3
- cleanup of RTC device node and addition of its clocks
- various board cleanups and improvements
- removal of pinmux node for GPIO lines
- cpufreq / DVFS
- HDMI output
- UART-based Bluetooth
- audio codec
- USB ports
- new boards
Most of the changes don't concern U-boot.
Signed-off-by: Chen-Yu Tsai <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.
Signed-off-by: Simon Glass <[email protected]>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <[email protected]>
|
|
These functions relate to memory init so move them into the init
header.
Signed-off-by: Simon Glass <[email protected]>
|
|
Move this function out of common.h and into a relevant header file.
Signed-off-by: Simon Glass <[email protected]>
|
|
This function is only used on ARM devices. Move it out of the common file
and to a arch-specific header.
Signed-off-by: Simon Glass <[email protected]>
|
|
This function related to timer and most of the timer functions are in
time.h, so move this function there.
Signed-off-by: Simon Glass <[email protected]>
|
|
These three clock functions don't use driver model and should be migrated.
In the meantime, create a new file to hold them.
Signed-off-by: Simon Glass <[email protected]>
|
|
This file is only used by PowerPC so move it to an arch-specific header
file.
Signed-off-by: Simon Glass <[email protected]>
|
|
This is an init-related function so belongs in that file. Move it.
Signed-off-by: Simon Glass <[email protected]>
|
|
This function is only used on ARM devices so does not belong in the global
common header file. Move it to an ARM header.
Signed-off-by: Simon Glass <[email protected]>
|
|
These functions relate to setting up the device tree for booting the OS.
The fdt_support.h header file supports similar functions, so move these
there.
Signed-off-by: Simon Glass <[email protected]>
|
|
This is a network function so let's move it into that header.
Signed-off-by: Simon Glass <[email protected]>
|
|
This is an init function so move it out of the common header. Avoid using
the typedef so that we don't have to include the global_data header file.
Also tidy up the function style in comments while we are here.
Signed-off-by: Simon Glass <[email protected]>
|
|
Add an arch-specific handoff header so that we can use the HANDOFF feature
on arm devices.
Signed-off-by: Michael Trimarchi <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Exports the serdes configuration as an environment variable for LS gen 3
SoCs, so it can be used in u-boot command line. It should particularly
be useful for applying Linux DT overlays for the given serdes
configuration.
This code is called from arch_misc_init and not from the existing
serdes_init function because it depends on U-Boot environment being set
up.
Signed-off-by: Alex Marginean <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
